v(0)= 100 sin(10) at te0v(0= 200 sin(107) at t>0ACA coil has been connected to an AC source for a long time and at t-0 the voltage sourcehas changed from v()= 100 sin(100) to v:(t)= 200 sin(10/). If the reactance andresistance of the coil is 40 and 30 respectively, then, the maximum steady state current ofthe coil is

Answered: Image /qna-images/answer/5f2ca3d2-468f-4ebe-bef9-ddd2387672d7.jpg

v0- 100 sin(10) at tKO v(0F 200 sin(100) att>0 A coil has been connected to an AC source for a long time and at t-0 the voltage source has changed from v(t)= 100 sin(100) to v:(t)= 200 sin(101). If the reactance and resistance of the coil is 40 and 30 respectively, then, the maximum steady state current of the coil is

v0- 100 sin(10) at tKO v(0F 200 sin(100) att>0 A coil has been connected to an AC source for a long time and at t-0 the voltage source has changed from v(t)= 100 sin(100) to v:(t)= 200 sin(101). If the reactance and resistance of the coil is 40 and 30 respectively, then, the maximum steady state current of the coil is

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.27P: An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8...

See similar textbooks

Similar questions

An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
An AC voltage source and a resistor are connected in series to make up a simple AC circuit. If the source voltage is given by AV = AVmax sin(27ft) and the source frequency is 19.0 Hz, at what time t will the current flowing in this circuit be 61.0% of the peak current? 5.922 X Note that the voltage in this AC circuit is a sine function. Did you use the correct units for the argument of the sine function? ms
Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of using a single 14 V dc voltage source.
A capacitor "C", an inductor "L" and a switch "S" are connected in series. When the switch is open, the plate to the left of the capacitor has charge "Qo". The switch is closed the load and current vary sinusoidally with time. Represent graphically the load "Qo" and the intensity of current "I" as a function of time "t", and explain why the current leads the load by a phase difference of 90°.
The ripple factor for pure dc is Answer:
An alternating current is given by the expression i = 200 sin (314t + T/6) amperes. The maximum value is and the frequency of the current is
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
A 230 V, 50 Hz a.c. supply is applied to a coil of 0.06 H inductance and 2.5 resistance connected in series with a 6.8 F capacitor. Calculate impedance and power consumption and power factor. Now ,In above a.c. circuit, A inductor of 0.2H is connected in parallel with the power supply, find new power factor and power consumption.
1. What impedance vector 0 – j22 represents:A. A pure resistance.B. A pure inductance.C. A pure capacitance.D. An inductance combined with a resistance.
Problem Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V dc voltage source.
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
A sinusoidal alternating voltage has an r.m.s. value of200 V and a frequency of 50 Hz. It crosses the zero axis in apositive direction when t = 0. Determine (i) the time when volt-age first reaches the instantaneous value of 200 V and (ii) thetime when voltage after passing through its maximum positivevalue reaches the value of 141.4 V.