A continuous conveyor with 140 m in length uses a belt with a width of 30" to transport a material with a specific weight of 2.3 t/m ³, with 100% pieces of 4 inches in diameter, the sides being tilted to 30° and with an accommodation angle of the load of 20° in continuous working regime (16 hours). Data: Use of 3 rollers and engine rotation: 600 rpm. Determine: TOUT TE a) b) c) d) e) f) Load capacity; Recommended operating speed; Selection of the roller series; bearing strength (use tapered bearings, service life 40,000 h); Spacing between rollers; Drive power

A continuous conveyor with 140 m in length uses a belt with a width of 30" to transport a material with a specific weight of 2.3 t/m ³, with 100% pieces of 4 inches in diameter, the sides being tilted to 30° and with an accommodation angle of the load of 20° in continuous working regime (16 hours). Data: Use of 3 rollers and engine rotation: 600 rpm. Determine: TOUT TE a) b) c) d) e) f) Load capacity; Recommended operating speed; Selection of the roller series; bearing strength (use tapered bearings, service life 40,000 h); Spacing between rollers; Drive power

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the principal data for a 10.7 m horizontal screw conveyor for 2.7 tonnes coal per hr, about 60 rpm. Worm gear speed reducer, 1750-rpm motor.
A belt conveyor transports 18 tonnes per hr at 20°. Determine the unit weight of belt material in kg/ply-cm width-m to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
Problem: A pump is driven by an electric motor through an open type flat belt drive. Determine the belt specificationsfor the following data.Motor pulley diameter= 400 mmPump pulley diameter = 800 mmCoefficient of friction for motor pulley = 0.30Coefficient of friction for pump pulley = 0.35Center distance between the pulleys=2000 mmRotational speed of the motor=2000 rpmPower transmission = 40kWdensity of belt material = 1000 kg/m3 width of the belt=240mmthickness of the belt = 5mm
Q2 Select a suitable chain drive to transmit 50 kW from an electric motor to a line shaft. The motor shaft r.p.m. are 1200, line shaft r.p.m. are 250 and approximate center distance is 600 mm. Assume service is 10hr/day, 6 days per week.
Q1: A simple flat belt drive system shown in the figure has a driving pulley diameter 220mm and runs at 800 r.p.m. clockwise; the diameter of driven pulley is 360mm. The contact angle is 210°. The belt wide is 20mm and 8mm thick. The belt mass per unit length is 0.5 kg/m and the maximum stress in the belt is 8 MN/m. If the coefficient of friction between the belt and pulley is 0.25; take the centrifugal force in to account and determine: 1. Redraw the figure and show (The Tight and Slack sides, tension and centrifugal forces directions at this two sides and the contact angles) 2. The speed of the belt on the driving pulley 3. The tension forces on the belt in the Tight and Slack sides 4. Power transmitted in the system 5. The generated Torque in the dri ing pulley Driven Pulley Driving Pulley
Q: Figure (1) shows a schematic drawing of a countershaft which is part of the conveyor system and supports two belt pulleys (A & B). The belt tensions are parallel for pulley B and inclincd with angle 45° for pulley A. The pulley A reccives a power from a motor and then delivers to conveyor belt through pulley B. All dimensions are in mm. Required: Design the shaft as shown in figure (1) at points O, A, B & E. Pulley B Material Discharge Material Fead Pulley A Conveyor System -Tail Pulley Gear box- Sepport Belt Motor Drive balt 300 310.5 N 400 46.5 N 150 Figure (1) 250 dia.- 300 dia. 50 N Pulley A Pulley B 270 N Page 1 of 1
(Q2) A pump is driven by an electric motor using an open type flat belt. Determine the width and length of belt for the following data: Power transmission = 15kW Rotational speed of the motor=1,440 rpm Motor pulley diameter = 250 mm Pump pulley diameter = 500 mm Coefficient of friction for motor pulley = 0.26 Coefficient of friction for pump pulley 0.22 Center distance between the pulleys = 1,200 mm Thickness of the belt = 5 mm Density of belt material = 1,000 kg/m? Allowable stress for the belt material = 2 MPa
Calculation for drive system and rack/spur gear of a crane. System needs to able to climb an incline of 12.457 beam tilt from horizontal With a payload weight of 27,500 lbs. using a 2 hp motor, 1725 rpm, 60 hz Gear reducer with 8.5 output rpm, ratio 204.75 Drive speed of 2.238 in/s Tooth force of 5931.798 lbf Rack - 20 PA, 2.5" face width, 1.5" thickness, 6' length, diametral pitch 5 in, 1018 steel Spur gear - 2.5" face width, diametral pitch 5 in, 20 PA, 30 teeth, 6.4 OD, 6 PD, 1144 steel Will this system work? If not, what material/gear reducer will work? Also, what is the max angle a 10 ft-lb electrical brake can statically hold a 27,500 lbs payload?
A pump is driven by an electric motor through a open type flat belt drive.Motor pulley diameter (DS) = 300 mm, Pump pulley diameter (DL) = 600 mm. The Center distance between the pulleys=1000 mm. Find the length of the belt in inches
A belt conveyor transports 18 tonnes per hr at 20°. Calculate the height in m to lift the load vertically up sufficient to give 33.5 m inclined belt length. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
Compute the theoretical capacity of a 8 inches diameter screw conveyor loaded at 45% of the full load. The screw shaft diameter is 2 inches with a screw pitch of 4 inches. The speed of the conveyor is 80 rpm.
A mini motorcycle is driven by a combustion engine with mechanical transmission. The 12Hp motor spins at a speed of 1150 rpm. The motorcycle runs at a linear speed of 45 km/h on 12-inch wheels. Preliminary center to center distance is 13”. This type of motorcycle requires two strands (conical double sleeve assembly) and is subjected to hard shocks. a) Calculate the effective power.b) Choice of chain and sprocket. (Standard part number, see catalog)c) Calculate the speed ratio. https://pdf.directindustry.com/pdf/martin-sprocket-gear/general-catalog/9091-246439.html