A mini motorcycle is driven by a combustion engine with mechanical transmission. The 12Hp motor spins at a speed of 1150 rpm. The motorcycle runs at a linear speed of 45 km/h on 12-inch wheels. Preliminary center to center distance is 13”. This type of motorcycle requires two strands (conical double sleeve assembly) and is subjected to hard shocks.   a) Calculate the effective power. b) Choice of chain and sprocket. (Standard part number, see catalog) c) Calculate the speed ratio.

Q: The flywheel in Figure.3 has moment of inertia of 33.5 ??. ?2 rotates at 365 rpm. A second flywheel…

A: Given: The moment of inertia of flywheel 1, I1 = 33.5 kg.m2 The moment of inertia of flywheel 1, I2…

Q: When engineers design belt drives and band brakes, they engineer them to withstand the frictional…

A: GivenmA=49kgμA=0.300μB=0.320d=0.250m

Q: Problem 4. For the belt drive shown below calculate the contact angle 0, if: D = 100 mm; d 3 30 тm;…

A:

Q: What is the no of teeth in driven sprocket? Select a suitable roller chain.What is it's label?…

A: Given: P=15 kW Driven speed =1400 rpm Driving speed =350 rpm center distance is nearly 40 times the…

Q: Q1 A two-stroke engine with loop scavenging should be designed to open the exhaust ports at 65°…

A: A two-stroke (or two-stroke cycle) engine is an internal combustion engine that completes one power…

Q: Calculate the capacity ol a bucket conveyor. The parameters are as follows.Belt speed 2.5 m/sec,…

A:

Q: A linear actuator having a in single-thread Acme screw is used to raise a load of 1600 lb. A plain…

A: Given:The diameter of the thread, The value of the load, The mean diameter of the thrust collar, The…

Q: Q1/A 6-in-wide polyamide F-1 flat belt is used to connect a 2-in-diameter pulley to drive a larger…

A: This question is related to the flat belts.The expression of angle of contact of the pulley.Here, C…

Q: mechanism like this one, if it is known the length of O2A (link 2) is 5 cm (link 3) is 4 cm (link 3)…

A:

Q: dimensions Q+ Design a can with following Angle of Ascot =150 degree, Angle ofDuell ho", Angle of…

A:

Q: 5. For the flat spring shown below (Ball feed device), with L = 65mm, t = 0.8 mm and b = 6 mm.…

A:

Q: Figure 1. The maximum extension of spring (ymax = 8.3 mm), the dynamic load varies from 250 N at the…

A:

Q: Refer to hoist system arrangement as in Figure Q1(b) and specifications details in Table Q1(b).…

A:

Q: A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum.  The 48V…

A: GIven data: The diameter of the drum is d=10 in The weight attached to the cable is Ft=500 lb The…

Q: Design a flat rubber belt that needs to transmit 100kW for a system consists of two pulleys of…

A:

Q: A nylon-core flat belt has an elastomeric envelope, is 250 mm wide and transmits 50 kW at a belt…

A:

Q: 3)Design a V – Belt drive to the following specifications Power transmitted = 75kw Speed of driving…

A:

Q: A vehicle engine is producing a brake power of 56 kW with a torque of 132.2 Nm. The final drive…

A:

Q: Give the suitable dimensions of a leather open flat-belt system according to the standards having…

A: Belt drives are used to transfer power from one shaft to another using pulleys that rotate at the…

Q: A 60 hp air pump blower in 18hr/day service running at a speed of 500 rpm is driven by means of a…

A: Write the correction factor for 18 hr/day service. fa=1.3

Q: elect a suitable chain for transmission, as follows:

A: Given: N1=1000 rpm N2=400 rpm P=12 kW minimum center distance=800 mm  Solicitation with moderate…

Q: Q10:- An epicyclic train of wheel is arranged as shown in the Fig. below. How many revolutions does…

A:

Q: A simple flat belt drive system shown in the figure has a driving pulley diameter 220mm and runs at…

A:

Q: A belt conveyor transports 18 tonnes per hr at 20°. Calculate the hp requirement to lift the load…

A:

Q: A belt conveyor transports 18 tonnes per hr at 20°. Calculate the total length to be sufficient to…

A: V-belt pulleys (likewise called vee belt bundles) are gadgets which send power between axles by the…

Q: 1) Find the equivalent spring, N/mm 2) Find the force, F Kl: =7 K5. =11 k K2 =8 X=10 mm К3 -9 K4 =10…

A: GIVEN DATA - A SPRING SYSTEM GIVEN WE HAVE TO FIND BOTH POINT 1 & 2

Q: Chain 8A having a pitch of 12.7 mm is used to connect 5 KW, 1400 rpm motor to a drilling machine.…

A:

Q: A belt conveyor transports 18 tonnes per hr at 20°. Determine the speed reducer power factor to lift…

A: Given Datam=18T/hrN=1750rpmS=33.5mV=61m/min

Q: For the Finishing Mill of a hot strip mill, the input shaft of several different gearboxes are each…

A: The objective of the question is to analyze the capabilities of a gearbox in a hot strip mill. This…

Q: 6-4

A: Step 1:Solutions :To figure out which forklift to suggest utilizing the IRR strategy, we really want…

Q: A shaft acting as simple supported beam is having a static deflection of 2.72 mm under a flywheel.…

A: As per given question  Deflections =2.72mm We have to find  critical speed in rad/sec

Q: . Determine: the diameter of shaft

A: Given: P= 20 kW N=750 rpm T1/T2=2.5 WA=300 N WB=250 Nshear stress=70 MPa kt=2 km=1.5 DB=1000 mm…

Q: 5. What do you understand by 'fluctuation of energy' and 'maximum fluctuation of energy'. 6. Define…

A:

Q: Design a helical extension spring to hold the roller follower against the cam as shown in Figure 1.…

A: Given dataMaximum extension of the spring ymax = 8.3mmVariation i dynamic force 250N to 400NDiameter…

Q: A chain drive is desired to couple a gearmotor with a bucket elevator. The 40 hp. gearmotor will…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.