A bent pipe is attached to a wall with brackets as shown. A force of F= 210 lb is applied to the end of the tube with direction indicated by the dimensions in the figure. Determine the support reactions at the brackets B, C, and D. Model these brackets as journal bearings (only force reactions perpendicular to the axis of the tube) and neglect couple moment reactions. Assume the distance between the supports at B and C and the tube bends nearby are negligible such that the support at C is directly above the support at D and the dimension g gives the distance between supports B and C. Enter your answers in Cartesian components.

A bent pipe is attached to a wall with brackets as shown. A force of F= 210 lb is applied to the end of the tube with direction indicated by the dimensions in the figure. Determine the support reactions at the brackets B, C, and D. Model these brackets as journal bearings (only force reactions perpendicular to the axis of the tube) and neglect couple moment reactions. Assume the distance between the supports at B and C and the tube bends nearby are negligible such that the support at C is directly above the support at D and the dimension g gives the distance between supports B and C. Enter your answers in Cartesian components.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid bar AB, pinned at end A, is supported by a wire CD and loaded by a force P end B as shown in figure. The wire is made of high- strength steel having modulus of elasticity E= 210 GPa. The diameter of the wire is 5mm. Determine the maximum load P that could be applied so that the vetical displacemt at B will not be more than 6 mm?
The shaft is made from a solid steel section AB and a tubular portion made of steel having a brass core. It is fixed at a rigid support at A and a torque T=50lb-ft is applied at C. Gsteel= 11,500 ksi Gbrass= 5,600 ksi What is the angle of twist at C? What is the maximum shear stress in the steel and brass? What is the maximum shear strain in the steel and brass?
/ The assembly consists of two 10-mm diameter steel rods AB and BC, and a rigid bar B. After applying the loads shown, determine: (1) The maximum normal stress developed in each rod. (2) The horizontal displacement of end C with respect to the fixed support at A. (3) Suppose that only rod BC is exposed to change in temperature, what would be the change that keeps point C in the original position. Use Est = 200GPA, xst= 12(10)-6 600 mm 400 mm 50 kN 40 kN B C 50 kN
W A L A Test beam Strain gauge (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. b Section A-A Strain gauge 1 Strain gauge 3 Strain gauge 2 B (b) Location of Huggenberger strain gauges a D Referring to the above figure, calculate the location of the centroid, the second moments and product of area for the cross-section if; • D = 67 mm • B = 41 mm • t = 2.41 mm. From these, calculate the position and orientation of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis). Also calculate the directions of the principal second moments of area. Next, graph as scale diagram of the cross-section and plot the neutral axis on that diagram in the correct location and indicate the direction of deflection for the same conditions
The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T 50 lb.ft is applied to it at C, determine the rotation angle that occurs at C relative to A and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst = 11500 ksi, Gbr 5600 Ksi. %3D %3D 3 ft 2 ft 0.5 in. 1 in. T = 50 lb ft
The shaft is made from a solid steel section AB and a tubular portion made of steel and having a brass core. If it is fixed to a rigid support at A, and a torque of T = 50 lb.ft is applied to it at C, determine the rotation angle that occurs at C relative to A and compute the maximum shear stress and maximum shear strain in the brass and steel. Take Gst = 11500 ksi, Gbr 5600 Ksi. %3D 3 ft 2 ft 0.5 in. 1 in. T 50 Ib-ft
Determine the magnitude of the pin force at A. Assume W = 845 Ib, a = 3.0 ft, b = 2.0 ft, r = 9 in. a a C В A W D Answer: A = i Ib
Determine the magnitude of the pin force at A. Assume W = 875 Ib, a = 2.8 ft, b = 2.1 ft, r = 8 in. C B W Answer: A = i Ib
Find the value of roller support reaction
W A Test beam A Strain gauge (a) Unsymmetrical cantilever beam with weight applied at the free end and at the "shear centre", so that there is no torsion induced. Section A-A Strain gauge 1 b Strain gauge 3 Strain gauge 2 B (b) Location of Huggenberger strain gauges a Referring to the above figure, calculate the location of the centroid, the second moments and product of area for the cross-section if; • D = 67 mm B = 41 mm t = 2.41 mm. From these, calculate the position and orientation of neutral axis for pure bending in the vertical plane (i.e. bending about a horizontal axis). Also calculate the directions of the principal second moments of area. Next, graph as scale diagram of the cross-section and plot the neutral axis on that diagram in the correct location and indicate the direction of deflection for the same conditions
The wooden strut is subjected to the loading shown. Draw the state of stress at point C on an infinite small element. The strut is supported by a bolt (pin) at point B and a roller support at point A. 50N S0N 40N 40 N -60 100 mm 50 mm 25 mm 200 mm 200 mm'200 mm'200 mm 100 mm 100 mm
Two identical metal sheets are formed into tubes with circular and square cross sections shown. If the same torque is applied to each tube, determine the ratios (a) Tcircle/Tsquare of the shear stresses; and (b) Ocircle/Osquare of the angles of twist. QE 2 it