6. An annealed copper strip 9 in. (228 mm) wide and 1.00 in. (25 mm) thick is rolled to a thickness of 0.80 in. (20 mm) in one pass. The roll radius is 12 in. (300 mm), and the rolls rotate at 100 rpm. Please note that the annealed copper has a true stress of about 12,000psi in the unstrained condition and the true stress reaches to 40,000psi at the end of rolling operation. Calculate the roll force and the power required in this operation. Note that the annealed copper has a true stress of about 12,000 psi in the unstrained condition, and at a true strain of 0.223, the true stress is 40,000 psi.

6. An annealed copper strip 9 in. (228 mm) wide and 1.00 in. (25 mm) thick is rolled to a thickness of 0.80 in. (20 mm) in one pass. The roll radius is 12 in. (300 mm), and the rolls rotate at 100 rpm. Please note that the annealed copper has a true stress of about 12,000psi in the unstrained condition and the true stress reaches to 40,000psi at the end of rolling operation. Calculate the roll force and the power required in this operation. Note that the annealed copper has a true stress of about 12,000 psi in the unstrained condition, and at a true strain of 0.223, the true stress is 40,000 psi.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROBLEM 3-18 GIVEN: A tension test was performed on a magnesium alloy specimen having a diameter 0.5 in. and gage length of 2 in. The resulting stress-strain diagram is shown in the figure. or (ksi) 4(0) 25 15 0.008 REQUIRED: If the specimen is stressed to 30 ksi and unloaded, determine the permanent elongation of the specimen.
A tensile load of 330,000 N is applied to a copper pipe with maximum allowable stress of 110 MPa. What should be the thickness of the pipe? 0 9.78 mm O 11.56 mm O 12.35 mm O 10.55 mm
A 1 foot plate with a 0.25-inch thickness has a width of 2.4 inch and a hole at the middle with a diameter of 2 inch. The material has an ultimate strength of 132 ksi and a yield strength of 84 ksi. A repeated 52N tensile load is applied along its neutral axis in the direction of its length at a temperature of 90 degree fahrenheit. The surface finish is Ground. The reliability of the material is targeted at 99.99%. Calculate: The Theoretical Stress Concentration Factor The Fatigue Stress Concentration Factor The Factor of Safety for the Goodman Criterion The Factor of Safety for the Soderberg Criterion The Factor of Safety for the Gerber Criterion The Factor of Safety for the ASME-Elliptic Criterion.
An aluminum pipe must not stretch more than 0.05in when it issubjected to a tensile load. Knowing that E=10.1x10^6psi and that the maximum allowable normal stress is 14ksi, determine (a) the maximum allowable length of the pipe, and (b) the required area of the pipe if the tensile load is 127.5kips.
In a standard tensile test, an aluminum rod of 20-mm diameter is subjected to a tension force of P- 30 kN. Knowing that E- 70 GPa, and the change in diameter of the rod- 0.00955 mm, determine the poissons' ratio v. 20n diateter gage length-150 0.33 O 0.6 0.29 O 0.35
A steel specimen is tested in tension. The specimen is 25 mm wide by 12.5 mm thick in the test region. By monitoring the load dial of the testing machine, it was found that the specimen yielded at a load of 160 kN and fractured at 214 kN. a. Determine the tensile stress at yield and at fracture. b. If the original gauge length was 100 mm, estimate the gauge length when the specimen is stressed to 1/2 the yield stress.
A steel specimen is tested in tension. The specimen is 1 in. wide by 0.5 in. thick in the test region. By monitoring the load dial of the testing machine, it was found that the specimen yielded at a load of 36 kips and fractured at 48 kips.a. Determine the tensile stress at yield and at fracture.b. If the original gauge length was 4 in., estimate the gauge length when the specimen is stressed to 1/2 the yield stress.
Hardness 6.54 (a) A 10-mm-diameter Brinell hardness indenter O produced an indentation 2.50 mm in diameter in a steel alloy when a load of 1000 kg was used. Compute the HB of this material. (b) What will be the diameter of an indentation to yield a hardness of 300 HB when a 500-kg load is used?
Zhpe Outine lece Select 834 Anange Oick Create wnd Shane Adobe PO Adite A SydesO upe iects tere Ding teting 1. (a) A tension test was performed on a magnesium alloy specimen having a diameter 12 mm and gauge 50 mm. The resulting stress-strain diagram is shown figure. Determine the approximate modulus of elastic and the yield strength of the alloy using the 0.2% offset method. (MPa) 280 245 (b) A tension test was performed on a magnesium specimen having a diameter 12 mm and gauge 1ength of 50 mm. The resulting stress-strain diagram is shown in the figure. If the specimen is stressed to 210 MPa and unloaded, determine the permanent elongation of the 210 175 140 specimen 105 70 35 (me 0.002 0.004 0.006 0.008 0.010 ANates
Question 7: Given a 1050 HR steel, estimate (a) the rotating-beam endurance limit at 106 cycles. (b) the endurance strength of a polished rotating-beam specimen corresponding to 104 cycles to failure (c) the expected life of a polished rotating-beam specimen under a completely reversed stress of 55 kpsi.
(Solid Mechanics) A setup for single-edge-notch-bending (SENB) tests is shown below. Support rollers provide frictionless contact with the specimen, while a load is applied at the middle of the top surface of specimen. The thickness of the specimen is 10 mm and the height W 10mm. The properties for this ductile alloy are E = 70 GPa, v=0.3, σᵧ = 400 MPa, Kᵢ? = 25 MPa.m¹/². (1) Ignore any crack or defects in the material, what is the maximum static force that the specimen could carry before failure? (2) A cyclic load of low amplitude 2.8 kN is applied. Because of the cyclic load a defect is nucleated on the edge and grows into a fatigue crack of 2 mm length shown in the right. If the cycling is interrupted, what is the maximum static tensile force that the specimen could carry? (3) With more cycles, the fatigue crack keeps growing. Estimate the critical crack length (a range is fine) at which the plate will fail from the low-amplitude cyclic load 2.8 kN only. (maximum two iterations are…
a) What is the stress in the bronze rod (in MPa)?b) What is the stress in the steel rod (in MPa)?