A bar with a right angle bend is supported by a collar A on smooth square rod, and by a roller at B. The forces and geometry are as shown in the figure and parameter table. Determine all the support reactions. Define all vector quantities to be positive in the positive coordinate axes directions. F₁ Az = Ay B₂ = parameter value 3 1.5 1.5 600 250 300 (MA) z - F₂ (MA)y= (MA) z= C L₁ L2 L3 F₁ F2 F3 B N N N units m m m N N N N-m N•m N•m A @ 080 BY NO SA 2021 Cathy Zupke

A bar with a right angle bend is supported by a collar A on smooth square rod, and by a roller at B. The forces and geometry are as shown in the figure and parameter table. Determine all the support reactions. Define all vector quantities to be positive in the positive coordinate axes directions. F₁ Az = Ay B₂ = parameter value 3 1.5 1.5 600 250 300 (MA) z - F₂ (MA)y= (MA) z= C L₁ L2 L3 F₁ F2 F3 B N N N units m m m N N N N-m N•m N•m A @ 080 BY NO SA 2021 Cathy Zupke

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The uniform wire is bent into the shape shown and held by the frictionless pin at O. Determine the angle 0 (0 ≤ 0≤ 180°) which will allow the wire to hang in the orientation shown. Assume a = 1.5r, b = 2.1r. Answer: 0 = a b b
Below presents a continuous beam with A being fixed and B is pinned and C has a roller. Take: E = 200 GPa 1 = 8 x 106mm Load = 2 kN A 5m B Using the following method: 2 KN + 2m + 2m |- You are tasked to analyze the continuous beam by calculating the: > the displacement on the beam at B and C and > the reaction at the supports Matrix Structural Analysis Use the following steps as a guide to analyze the beam: Matrix Structural Analysis ✓ Produce Notations ✓ Establish the known displacements and known external load ✓ Produce Member Stiffness Matrix ✓ Displacement and Load ✓ Calculating the displacement Calculating the reaction at the support
A rectangular tetrahedron has six sides of length 9 cm. If a force of 600 N is applied along edge BC as As shown, determine the moment of the 600-N force about edge OA. A B 600 N
3. Rigid member ABD is connected to elastic member CDE as shown. For the given loading, what are the vertical displacements of points A and E? A 20KN dimensions in meters B rigid I ст 0.4 E 0.2 5kN E=7oGPa A=100mm²
As shown in the figure, rod AB is steel and rod BC is an aluminum, are hinged to rigid suppots which are pinned together at B to carry a vertical load P=20kN. Each rod has a cross-sectional area of 400mm^2 and Es=200000Mpa and Ea=70000Mpa. Compute for the deformation of steel and aluminum and for the horizontal and vertical displacements of point B.
A beam of length /= 1m, which is clamped at both ends, is modelled using four flexural elements. The first modeshape of the beam is described by: 2 0.544 3.045 1.000 0.000 0.544 - 3.045 Note that Y₁ = ₁=Y₁ = =0 due to the boundary conditions. Recalling that displacement of a flexural element is given by: 0 y=S₁₂(x) y₂ +S₂(x) @ + S₂(x) y₂ + S₂(x) O 1 1 1/2 2 where the shape functions are given by: 2 $, (x) = 1 - 3 ( - ) ²+ ² ( ² ) ³* +2 x3 $₂(x)=x- 2 + ² + + ²2 L L² x $₂(x) = ³ ( 7 ) * - 2 ( ² ) ³ +2 x3 5(x) = -1/ 2 + + 20 S₂(x) L L² Find the displacement of the first modeshape at position x=//8. Express your answer to three decimal places and do not include units in your answer.
3.) Rigid bar BC is supported by aluminum rod (1) and bronze rod (2), as shown in the figure. If the maximum force the aluminum rod can take is 30040 N and the maximum force the bronze can take is 31190 N, determine the maximum force P that can be applied to the rigid bar BC to remain in equilibrium. Assume that L = 1100 mm and a = 500 mm. [Answer: P = 57.2 kN] Hint: You should effectively solve for 2 different values of P by imposing one restriction at a time and solving for P based on each one. Then determine which of the two possibilities for P would actually satisfy both restrictions. A (1) (2) B C
X=75MPa Y=90MPa S=40MPa D=-10 Note: If the angle D is positive, then the shear stress is in the direction shown on the unit element figure; if it is a minus sign, then the shear stress is in theopposite direction shown on the unit element figure.
Problem 5.2 The rigid bar shown is pinned at A and supported by two steel rods, each having a diameter of 1 in. The system is subjected to a load P = 2 kip (note: kip refers to kilopound). If the bar is assumed to be rigid (meaning that it does not bend due to the loading) and is initially vertical, determine: A) The force in each bar when P is applied B) The displacement of end B when P is applied a = 1 ft, b= 1 ft D -b 2b B E AG Check your work: FEF = 1.26 kips a a a a P
3. A force P is applied to the rigid lever arm ABC as shown. The arm rotates counterclockwise about pin A through an angle of 0.06°. Calculate the normal strain developed in wire BD. Answer: EnD = 0.0014 mm/ mm 300 mm B 400 mm
. Consider the following wooden T-beam on its side. It consists of two wooden parts glued together. Assume the glue nas a perfect bond. The densities of the two wooden parts differ and are indicated on the figure. The figure is not to scale. y Pq = 900 kg/m %3D 17 mm P2 = 740 kg/m? 20 mm 150 тm Determine the a-coordinate I of the center of mass of the T-beam. 90 mm
T·r T (from torsion) = Tr4 J ="- (Solid rod) F Onormal = A o (from bending) M•y - (Solid rod) The solid rod shown in the figure below has diameter of 1.25 in. If it is subjected to the force of 60 lb, determine the state of stress at point A using the principle of superposition. Neglect the weight of the rod, and the stress due to the I %3D I 4 transverse shear force. 60 lb k-10 in.- 15 in. Front View -20 in. В