Below presents a continuous beam with A being fixed and B is pinned and C has a roller.Take: E = 200 GPa1 = 8 x 106mmLoad = 2 kNA5mBUsing the following method:2 KN+ 2m + 2m |-You are tasked to analyze the continuous beam by calculating the:> the displacement on the beam at B and C and> the reaction at the supportsMatrix Structural AnalysisUse the following steps as a guide to analyze the beam:Matrix Structural Analysis✓ Produce Notations✓ Establish the known displacements and known external load✓ Produce Member Stiffness Matrix✓ Displacement and Load✓ Calculating the displacementCalculating the reaction at the support

Answered: Image /qna-images/answer/df34dec3-e278-4a45-a469-104121936024.jpg

Answered: Below presents a continuous beam with A…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h= 430 mm tw= 12 mm d= 110 mm t= 9.6 mm Additionallv: • The area of each pipe is A = 3028 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is I>= 320410000 mm4. If the beam will be subiected to a shear force of V = 110 kN, determine the shear stress at point K, located at yK = 70 mm below the z centroidal axis.
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
Determine the support reaction Rc, in the simply supported beam shown below. Your answer should be in terms of W, L and a. W BY Ro Rx A. Rc-3W OBRC=WaL OC Re WaL OD Rc=-W O E. Rc=3W은 %3D F. Re=w
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
3. The length of 2-mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 1.5 mm exists between the end B of the rigid beam ACB and a contact point E. If E = 200 GPa, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D X 0.25 m 20 kg A 1.5 mm C 0.08 m 0.32 m E
The assembly consists of three titanium (Ti-6A1-4V) rods and a rigid bar AC. The cross-sectional area of each rod is given in the figure. If a force of 60 kip is applied to the ring F, determine the horizontal displacement of point F.
A load of P = 2800 N acts on the machine part shown. The angle between the line of action of Pand the vertical y axis has a value of - 75°. The overall dimensions of the machine part are a= 125 mm, b - 55 mm, and c-75 mm. K B.
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B1= 0.8 m; B2 = 1.0 m; B3= 0.6 m. Determine the axial load acting on bar B3 in kN. 35KN В1 B2 ВЗ ... 10KN 15KN 30KN A 35 20 10 D 5
d. Calculate "P" in KN considering failure on shear on rivets Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
2max 1 max A beam comprises of two metals (1 and 2). Both the metals are in contact as shown in figure. If a moment M, is applied, what is the value of 0₁/0... It is given that both the metals will bend separately about their own neutral axis. Also draw bending strain and bending stress diagram. Mo Mo at th Jicc E₁, I, E2, 12 d₁ d₂
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa Aluminum L=2m A=500mm 2m 2m E-72Mра P=20KN
Four forces are applied to the machine component ABDE as shown. Replace these forces with an equivalent force-couple system at A.

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Below presents a continuous beam with A being fixed and B is pinned and C has a roller. Take: E = 200 GPa 1 = 8 x 10 mm* Load = 2 kN 5m 2 KN + 2m + 2 m ▸ the displacement on the beam at B and C and the reaction at the supports F You are tasked to analyze the continuous beam by calculating the: