The rigid bar shown is pinned at A and supported by two steel rods, each having a diameter of 1 in. The system is subjected to a load P = 2 kip (note: kip refers to kilopound). If the bar is assumed to be rigid (meaning that it does not bend due to the loading) and is initially vertical, determine: A) The force in each bar when P is applied B) The displacement of end B when P is applied a = 1 ft, b = 1 ft F D 2b b B E P

The rigid bar shown is pinned at A and supported by two steel rods, each having a diameter of 1 in. The system is subjected to a load P = 2 kip (note: kip refers to kilopound). If the bar is assumed to be rigid (meaning that it does not bend due to the loading) and is initially vertical, determine: A) The force in each bar when P is applied B) The displacement of end B when P is applied a = 1 ft, b = 1 ft F D 2b b B E P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

8.10 This is steel, consisting of 9 rods that are articulated together in the nodes. There is a fixed bearing in A and a roller bearing in B. The steel is loaded with a point load, P, in the middle. The maximum permissible normal stress is oy = 200 MPa. Cross section: s9 S8 54 53 55 s1 S7 d = 40 mm S2 S6 1m 1m 1 m 1 m a) Calculate the rod forces. Express the answers with P, and state whether they are stretched or pressed. Is there any zero spells? b) Determine how large the load P can be without material breakage or buckling the spells. 3 m
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 519 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 633 mm2. For the 36 kN force shown, determine the deflection of B (mm) *deflection should have a negative sign if compression and positive if tension. Also, your final answer should have two decimal places
The rigid beam is supported by three suspender bars. Bars AB and EF are made of aluminum (Eal = 70 GPa) and bar CD is made of steel (Est = 200 GPa). If each bar has a cross-sectional area of 450 mm² and P = 50 kN, determine the following for each bar: a) Stresses (in MPa) b) Elongation (in mm) al B st D al 0.75 m 0.75 m 0.75 m 0.75 m 2P F 2 m E
A rigid bar AB, pinned at end A, is supported by a wire CD and loaded by a force P end B as shown in figure. The wire is made of high- strength steel having modulus of elasticity E= 210 GPa. The diameter of the wire is 5mm. Determine the maximum load P that could be applied so that the vetical displacemt at B will not be more than 6 mm?
Rigid bar ACB is supported with a pin at A and an elastic steel rod at C. The elastic rod has a diameter of 26 mm and modulus of elasticity E = 200 GPa. The bar is subjected to a uniform load q on span AC and a point load at B. Elastic rod Rigid bar A q = 7 kN/m -2.5 m- mm I C 0.75 m -0.75 m- = 14 KN B Ⓡ Calculate the change in length of the elastic rod (in mm). (Use the deformation sign convention.) mm What is the vertical displacement at point B (in mm)? (Assume the positive direction is upward. Use the statics sign convention.)
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. C D I-KE -1.2 m-1.2 m 1.2 m B
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial load acting on bar Bị in kN. 35KN В1 B2 ВЗ ... 10KN 15KN 30KN Determine the axial load acting on bar B2 in kN. Determine the axial load acting on bar B3 in kN. Determine the axial stress of bar B1 in MPa. Determine the axial stress of bar B2 in MPa. Determine the axial stress of bar B3 in MPa. Determine the total deformation of the bars B1, B2 and B3 in mm. Determine the deformation of the bar B in mm. Determine the deformation of the bar B2 in mm. Determine the deformation of the bar Bz in mm. 35 А 35 B 20 10
The rigid beam is supported by three suspender bars. Bars AB and EF are made of aluminum (Eal = 70 GPa) and bar CD is made of steel (Est = 200 GPa). If each bar has a cross-sectional area of 450 mm² and P = 50 kN, determine the following for each bar: a) Stresses (in MPa) b) Elongation (in mm) al B st D C al 0.75 m 0.75 m 0.75 m 0.75 m 2P F 2 m E 1/1
The beam has a rectangular cross section and is subjected to the loading shown. Determine the components of stress ox, oy, and Txy at point B. 800 N B 1000 N 15 mm 20 mm 20 mm 15 mm 100 mm 10 mm
#3A. The rigid bar AB, attached to two vertical rods as shown, is horizontal before the load P is applied. Determine the vertical movement of P if its magnitude is 50 kN. Aluminum L= 3 m A = 500 mm² E = 70 GPa 3.5 m P B Steel L = 4 m A = 300 mm² E = 200 GPa 2.5 m #3B. A steel rod is stretched between two rigid walls and carries a tensile load of 5000 N at 20°C. If the allowable stress is not to exceed 130 MPa at -20°C, what is the minimum diameter of the rod? Assume a=11.7µm/(m °C) and E=200 GPa. C
The rigid bar AB of negligible weight is supported by a pin at O. When the two steel rods are attached to the ends of the bar, there is a gap A = 4 mm between the lower end of the left rod and its pin support at C. %3D Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm? for rod BD. Use E = 200 GPa for steel. A В 0.75 m 1.5 m > 2 m D