ion 11.43 A balanced A-connected load has an impedance of60+j45 0/o. The load is fed through a line havingan impedance of 0.8 + j0.6 /p. The phase voltageat the terminals of the load is 480 V. The phase se-quence is positive. Use VAB as the reference.a) Calculate the three phase currents of the load.b) Calculate the three line currents.c) Calculate the three line voltages at the sendingend of the line.

A balanced A-connected load has an impedance of 60 + j45 /6. The load is fed through a line having an impedance of 0.8 + j0.6 0/6. The phase voltage at the terminals of the load is 480 V. The phase se- quence is positive. Use V a) Calculate the three phase currents of the load. AB as the reference. b) Calculate the three line currents. c) Calculate the three line voltages at the sending end of the line.

A balanced A-connected load has an impedance of 60 + j45 /6. The load is fed through a line having an impedance of 0.8 + j0.6 0/6. The phase voltage at the terminals of the load is 480 V. The phase se- quence is positive. Use V a) Calculate the three phase currents of the load. AB as the reference. b) Calculate the three line currents. c) Calculate the three line voltages at the sending end of the line.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.23P: A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the...

See similar textbooks

Similar questions

A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the positive terminal of the source. Determine the real and reactive power and state whether the source is delivering or absorbing each.
In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the line-to-neutral voltages are always equal to zero. (a) False (b) True
In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the complex power for the L2 load?
8. The total power supplied to a balance delta load is found in the same way as for a balance wye load. True False Either Neither 12. A load of 20 + j35 ohms is connected across a 220 V, 60 Hz supply. Find the reactive power of the load in var. 595 2420 1042 1382 13. A type of DC source where the characteristic output voltage has perfect unidirectional waveform and is based on electrochemical principle. Generator Inverter Converter Battery 14. Calculate the Rf of a circuit whose impedance is 20+j35 and current of 2A. 0.86 0.91 0.50 0.71 15. What capacitor shall be installed in parallel with a circuit to achieve a unity power factor if the reactive power of a circuit is 200VARS and the voltage is 100V. 80.45 microfarad 53.05 microfarad It's already in unity 62.45 microfarad
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
2. A single-phase a.c. distributor AB is fed from end A and has a total impedance of (0-2 + j 03) ohm. At the far end, the voltage V = 240 V and the current is 100 A at a p.f. of 0-8 lagging. At the mid-point M, a current of 100 A is tapped at a p.f. of 0-6 lagging with reference to the voltage Vy at the mid-point. Calculate the supply voltage V, and phase angle between V, and Vg- [292 V, 2-6°] a loade
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
2. A voltage applied to a load is V=208420°V and current through load is I=10 &-10° A. Find the following [SO 1] o complex power consumed by load • Is the load inductive or capacitive? o the power factor of the load o the reactive power consumed or generated by the load. o Does the load consume or supply reactive power? 3. A single phase motor draws 20 kVA at 0.70 lagging power factor from a 120 V source. The PUD desires to improve the power factor to 0.9 lagging by connecting a shunt capacitor bank across the terminals of the motor. Determine the size of the capacitor bank in VARS. Calculate the following: [SO 1] a) What are the initial load current, real and reactive powers of the load? b) What are the real and reactive power after adding the capacitor bank? c) What is the kVAr rating of the capacitor bank? (3) d) What is the load current? di) How is the load current affected by the load reactive power?
Three Impedances each of (8 - j24)2 are connected in mesh across a three-phase 420V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip) Line current real power reactive power
5. The figure below shows two star connected loads with three phase power. The voltage source is 120Z0°. The loads are Z₁ = 10 + j4 № and Z₂ = 2 +j3 №. The cables are negligible. Calculate: a) the line and phase current. b) the real power from the source. c) the reactive power of the circuit. Is V N Z₁ Z₁ Z₁ Z₂ Z₂ N N Z₂
If a A-connected load has a balanced impedance ZA 94 - 17° 2 and a voltage = = / VBC = 265 82° V rms, what is the magnitude of the current Ia (in A rms)? C V cn Van a Answer: n Von b Ia Ib 20 B IAB IBC ZA ZA ICA C