2. A 3-phase 4-wire balanced power system with a positive sequence is supplied to a balanced 3-phase load connectedto a Y type with an impedance per phase (Z5) o12 + j16 N The impedance in the transmission line isi 0.02 Q.and resistance The neutral wire is 0.05 Q The line voltage at the load is 2200 V. Find the following values.2.1 Line currentI, IBnd ec2.2 Voltage V Vanbnen2.3 Complex power (S) supplied by the power supply

Answered: Image /qna-images/answer/e5f9116c-340d-478a-b6c8-da2e54069bbb.jpg

A 3-phase 4-wire balanced power system with a positive sequence is supplied to a balanced 3-phase load connected to a Y type with an impedance per phase (Z5) o12 + j16 2 The impedance in the transmission line is 0.02 Q and resistance The neutral wire is 0.05 Q The line voltage at the load is 2200 V. Find the following values. 2.1 Line currentI, IRnd ec 2.2 Voltage V Vn an' 2.3 Complex power (S) supplied by the power supply

A 3-phase 4-wire balanced power system with a positive sequence is supplied to a balanced 3-phase load connected to a Y type with an impedance per phase (Z5) o12 + j16 2 The impedance in the transmission line is 0.02 Q and resistance The neutral wire is 0.05 Q The line voltage at the load is 2200 V. Find the following values. 2.1 Line currentI, IRnd ec 2.2 Voltage V Vn an' 2.3 Complex power (S) supplied by the power supply

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Ztoad 500 236.87° ohm , and the transmission line's impedance is Zine = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Zload = 500 236.87° ohm, and the transmission line's impedance is Zline = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
1. Calculate the line currents for phase a, b and c.2. Calculate the line-to-neutral voltages at the load for phase a, b and c.3. Draw the phasor diagram of the source line-to-neutral voltages and line currents.
Q. 2a) The impedance Zi and Z2 are connected in parallel across 200 V, 50 HZ single phase ac supply. Zi carries 2 A at 0.8 lag p.f. If the total current is 5 A at 0.985 lagging p.f. Determine - 1. Value of Z, and Z2 2. Total power and power consumed by Z2.
4) A balanced delta connected load of ...+j18 ohm per phase is connected at the end of a three phase line as shown in figure. The line impedance is 1+j2 ohm per phase. The line is supplied from a three-phase source with a lie- to-line voltage of 207.85 V rms. Taking Van as reference, determine the following: a) Current in phase a. b) Total complex power supplied from the source. c) Magnitude of the line-to-line voltage at the load terminal. (Please determine the impedance value within the specified limits: 16-26 V. By considering the impedance value you determined yourself, solve the question.) ao- |V₂| bo Co- 1 +j2 Ω = 207.85 V www Figure a Jum ...+j18 n b
2. A single-phase are distributor AB is fed from end A and has a total impedance of (0.3-0.3) ohm. At the far end, the voltage V-240V and the current is 100A at a p.f. of 0, 8 lagging. At the mid-point M. a current of 100 A is tapped at a p... of 0.6 lagging with reference to the voltage V_{M} at the midi-point. Calculate the supply voltage V Lambda j sending current I_{N} and the phase angle between V_{A} and V_{E}
A balanced delta connected load of 15 + J18 Q per phase is connected at the end of a three-phase line as shown in Figure 2.25. The line impedance is 14-j2 Q per phase. The line is supplied from a three-phase source with a line-to-line voltage of 207.85 V rms. Taking Van as reference, determine the following: (a) Current in phase a. (b) Total complex power supplied from the source. (c) Magnitude of the line-to-line voltage at the load terminal. 1+j2N wwwm VL = 207.85 V bo Co- FIGURE 2.25 Circuit for Problem 2.13. b a 15+j18 N
(b) A symmetrical delta-connected 415V three-phase supply is feed to an asymmetrical delta- connected load as shown in Figure Q2(b). Assume that it is a RYB sequence. The impedances of the load are ZrY = 50 + j50 N , ZYB = 150 + j0 N and ZBr = 50 –j50 N. jos (i) Determine and draw the phasor diagram of phase currents in the load. (ii) Determine and draw the phasor diagram of line currents in the system.
AC Power and Power Factor 1. Two loads are connected in parallel across a 13,200-volt line. Load A draws 200kW at 0.6 p.f. (lagging), load B takes 200kVA at 0.8 p.f. (lagging). Find the reactive, apparent and true power and the line current.
1. Given the circuit below, the phase voltages are given by Van = 20040° Vrms. The source impedance is 5 + j7 per phase and the wire impedance is 8 +j10 per phase. Let the load impedance be Zy = 50 ohms. Find: Van Vin Ven a. II, and Ic b. c. VAN, VBN, and VCN, and VAB, VBC, and VCA Z₂ Z₂ Z₂ Zw Zw Zw B C le N
Figure Q2(a) shows a positive sequence three phase circuits. Given a line-to-line voltage at generator, ERY = 415230°V. With assumption that all load impedance are balanced, Zn=Zyb=Zbr= 15 + jl8 2, determine all phase currents at each load and line currents. Include the phasor diagram for all currents in your analysis. R Zry Zyt Figure Q2(a) If the transmission line in three phase circuit at Figure Q2(a) has a impedance of 1+j20 for each phase, determine the phase voltages for each load with using an appropriate analysis. Use phase voltage at generator, ERN as a reference. Then determine the total apparent power, active power and reactive power supplied by the generator.