a 6uF capacitor with an initial potential difference of 17V is discharged through a resistor when a switch between is closed at t = 0. Att = 2s, the potential difference across the capacitor is 4v. what is the resistance of the resistor kohms (1 kohms = 10*3ohm)?

a 6uF capacitor with an initial potential difference of 17V is discharged through a resistor when a switch between is closed at t = 0. Att = 2s, the potential difference across the capacitor is 4v. what is the resistance of the resistor kohms (1 kohms = 10*3ohm)?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 3RQ: A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted...

See similar textbooks

Related questions

Q: A conductor of length = 1 m with a current = 60 A is placed perpendicularly to the field lines in a…

A: The magnitude of electromagnetic force on the wire is, Fmag=36.0NExplanation:Step 1:Step 2:

Q: A magnetic core with an air gap is shown below. For a relative permeability is 3500, and the space…

A: In this question we need to find the reluctance of air gap.

Q: Vi (+ R₁ R₂ (=R.) W ww R -0% Find the transfer function Vo/v; for the network

A: Please see the explanation Explanation:Step 1:

Q: 4.34 An 8 × 1 multiplexer has inputs A, B, and C connected to the selection inputs S2, S1, and S 0,…

A: According to the question, an 8 × 1 multiplexer has inputs A, B, and C connected to the selection…

Q: b) Suppose the signal x(t) = 2 cos(4000лt) is instantaneously sampled at the rate of 3000 samples…

A: Sampled output is 2cos(2000πt)Explanation:Step 1: The signal we have is x(t) =…

Q: . A systematic cyclic cod with generator Polynomial g(x) = x²+ x³+ 1 is used to protect data grouped…

A: According to the question,a) Using the encoder logic circuit, find the transmitted word for data…

Q: Q3// A//Determine the logic function performed by the CMOS digital circuit of Fig: -VOD B-

A: Explanation:CMOS consists of NMOS and PMOS devices in series.NMOS is ON for logic 1PMOS is on for…

Q: o H.W: An angle modulated signal has the form: u(t) = 100 cos[2лft + 4 sin 2000лt] where fc 10 MHz.…

A: The angle-modulated signal has the form: u(t) = 100cos[2πfct + 4sin(2000πt)] Where fc = 10 MHz…

Q: A BJT Current Mirror is shown below. The nominal current transfer ratio is 1, and the transistors…

A: a) 75.806 uAb) 0.589%Explanation:Step 1:Step 2:

Q: 7.27 At 2 GHz, the conductivity of meat is on the order of 1 (S/m). When a material is placed inside…

Q: Consider the circuit shown on the figure below (Figure 1). Suppose that Ri 12 11. Ry 2811, Rs 11 12…

A: The given circuit is drawn below:

Q: 1.) What are at least the 2 goals or concern of an electrical engineer in the transmission (or…

A: 1) What are at least the 2 goals or concern of an electrical engineer in the transmission (or…

Q: Given the Vth = 5V and the Rth = 650.3 ohms, what would the new output voltage be if you added a 500…

A: The objective of this question is to find the new output voltage when a 500 ohm load resistor is…

Q: a) I (0-) equals b) I at infinty time equals A c) The time constant t equals d) at t=5ms equals A A…

A: Since you have posted the questions with multiple subparts. so we are supposed to answer 3…

Q: Find R: eq If three resistors of 2, 4, and 60 connected in series.

A: When resistors are connected in series, they form a single path for the current to flow through, one…

Q: 6. A (9,3) cyclic code has the generator polynomial g(x) = 1+ x²+x6. a) Use the encoder circuit to…

A: Output code word for information word is[101],Verify the answer (a) by using long division.discuss…

Q: The switch in the circuit in Fig 5 has been closed f a long time and is opened at t = 0. Find i(t)…

Q: Calculate the valve coefficient (Cv) of a standard globe control valve using the following…

A: The solution explained in detail.The final solution will be Cv=232.1634Explanation:Please follow the…

Q: A conductor of length 0.5 m is moving with the speed of 8 m/s in a perpendicular magnetic flux…

Q: - 7. Show the result of sin(wt – 30°) + cos(wt + 10°) in cosine format. With the use of phasor. a)…

A: Given that,The objective is to find the result of in cosine format.

Q: Q3\ Draw the symbols of the following electronic devices. 1- coil, 2- Zener diode, 3- npn…

A: Draw the symbols of the following electronic devices1- coil, 2- Zener diode,3- npn transistor, 4-…

Q: VIÐ) R₁ www R3 R2 C₁ Ry HH L₁ чи R5 ww 42 ง m чи www L C3

Q: * Determine i(t) in the network shown 5+10u(t) V 102 402 www ww m 2 H F We first find the initial…

Q: 8. Find vo(t) in the circuit below, where R = 34 . 60 sin 200t V +1 50 Ω R ww HH 50 μF + 0.1 H v(t)

A: The circuit diagram,

Q: Needs Complete typed solution with 100 % accuracy.

A: The objective of the question is to find the Fourier series expansion of the given signal f(x) = x +…

Q: For the circuit shown in Fig. 8(c), find the collector current IC and VCE Use beta = 50 and VBE=0.7V

A: In the given question we need to calculate the Q point of the following circuit.

Q: 3. The following figure shows the circuit for a full-wave bridge rectifier. Assume the diodes are…

A: Since you have posted the questions with multiple subparts. So we are supposed to answer 1st 3…

Q: Q6) Calculate the gain of a parabolic antenna of 100% illumination and having a 30° radiation…

Q: Solve the circuit by nodes (LCK) and find the function IR(s)/I(s) Please solve the system showing…

Q: x(t) Consider a periodic signal of the form Σp(t-4n) where p(t) = [[0,1](t). Find an explicit…

A: A periodic signal is given by⇒x(t)=∑n=−∞∞p(t−4n) .Where p(t)=I[0,1](t).The impulse response of the…

Q: Si 0.7v lov = R = 1 K~ which Birde is 0V he 0.3v ON for ол ble Circuit and why ?

A: Given:a circuit,we need to find:which diode will turn ON and why?

Q: Calculate the Y22 parameter (in Siemens up to two significant digit) of the below circuit if R-57.…

A: In this question, we need to determine the admittance parameters Y22 .

Q: 8. Consider the (7,3) systematic cyclic code with g(x) = x²+ x³+ a) Code table & min. Hamming…

A: According to the question, consider the (7,3) systematic cyclic code with g(x) = x4 + x3 + x2 + 1.…

Q: Determine Vo and Ip for the circuit in the Figure below +20 V Si Si V www 4.7 Q

A: Refer to the given figure, the diodes are silicon type diodes. Therefore,The forward voltage drop…

Q: 3 V Given R1 = 6k, R2 = 4k, address following questions/tasks: (1) Which diode is forward biased, D1…

A: The circuit diagram,

Q: 1. For circuit-1, (Values of all the Resistors are in Ohms). a. Determine the equivalent resistance,…

A: Given:a circuit, we need to find:a) equivalent resistance of the circuit.b) Current through each…

Q: 4 For the circuit shown in the given figure, V, 8020 V. Determine the load impedance Z for maximum…

A: Determine the load impedence of maximum power transfer and determine the maximum power absorb by…

Q: Problem 5.1: Calculate the voltage at V relative to ground in the following circuit. Assume the…

A: In this question, we need to determine the value of voltage V w.r.t to ground.

Q: * 7.3 The electric field phasor of a uniform plane wave is given by E = ŷ 10ej0.2z (V/m). If the…

Q: Find approximate values for Ic and Vce in the circuits below if T = 25° C, Beth = 200 +12V b) c)

A: In the given question we need to calculate the Q point .

Q: 2. An 12 volt battery is connected to a configuration of resistors as shown. 12V ↑ 1= R₁= le R₂=2-2…

A: According to question, we need calculate equivalent resistance and each resistor current and…

Q: 3) In the PNP transistor circuit shown, find all the transistor currents and voltages (IC, IB, IE,…

A: Details solution is given below Explanation:Step 1:

Q: G(s) = (s+5) (s²+5s+7)(s²+2s+5)

A: Given: H(s) = 1 G(s) = (s+5) / ((s^2+5s+7) * (s^2+2s+5))(s2+5s+7)→Poles: −2.5+1.658i,−2.5−1.658i…

Q: Question: What is the primary function of a diode in an electrical circuit? A) To regulate voltage…

A: Option A is wrong because the Zener diode is used to regulate the voltage, but the normal PN…

Q: I want to know how to solve equation 1 into equation 2.

A: The step by step explanation of simplifying the equation 1 to get the equation 2 needs to be…

Q: 10 Ω For the circuit shown, find V1 & V2. W 10/0° + +j2012 WWW V₂ 150 13 -j5Q

A: In this question, we need to determine the voltages V1 and V2 as shown in the circuit. We solve this…

Q: IL(0-) = IA, determine IL (t) for t (greater than equal to)0s using the Initial & Final…

A: see the attached answer. Page no are written on top right corner to avoid confusion Explanation:Step…

Q: Problem 1: u(t) Input force State-space representation z₁(t) zz(t) T m1 TE b₁ b₂ m2 mrr m k₂ k₁ 1)…

A: This is a physic question

Q: The rydberg formula is a concept only found in your OpenStax book, It is convered in sections 6.1…

Q: = 7.9 Three vertical N/2 dipoles are mounted 3λ apart in the same horizontal line and are fed with…

A: According to the question, three vertical λ/2 dipoles are mounted 3λ apart in the same horizontal…

Concept explainers

Capacitor

The capacitor is an element used to store electrical energy in the electrical field. A capacitor is a form of passive energy.

Question

a 6uF capacitor with an initial potential difference of 17V
is discharged through a resistor when a switch between
is closed at t
= 0. Att 2s, the potential difference
=
across the capacitor is 4v. what is the resistance of the
resistor kohms (1kohms = 10^3ohm)?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Summarize the given data.

VIEW

Step 2: Determine the resistor value.

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 10 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
List the five capacitor replacement rules.
A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?
Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
Energy stored in capacitor. Answer it in 30 mins. Draw/sketc the problem thank you. Write the basic equation before the soln. Thank you
Please explain this question properly A capacitor has a reactance of 40 when operated on a 50 Hz supply. Determine the value of its capacitance. In a series R–L circuit the p.d. across the resistance R is 12V and the p.d. across the inductance L is 5V. Find the supply voltage and the phase angle between current and voltage
The plates of a parallel-plate capacitor are square and have the length of one side. 20 cm and the distance between the plates is 0.5 cm. The material between the plates is air.What is the capacitance of a parallel plate capacitor in farads?
An initially uncharged parallel plate capacitor is connected to a circuit containing a battery with emf -15V and a resistor, R = 8.5MN as shown in the figure to below. The capacitor whose plates have an area of A = 3.1mm² are separated by a distance of d = 3.4mm and one third of the capacitor is filled with a dielectric material, K₁= 1.1 and the rest (two thirds) is filled with another dielectric material, K₂=4.5. At t=0 the switch is closed. 7.1 seconds after the switch is closed the electric field within the first dielectric material (₁) is observed to be 15 x 10³ N/C. Find the potential difference across the capacitor at this instant (t = 7.1 s) in terms of permitivity of free space €0? Express your answer using zero decimal place. R S K₁ K₂
A 10-9.F capacitor (1 nanofarad) is charged to 50 V and then disconnected. One can model the charge leakage of the capacitor with a RC circuit with no voltage source and the resistance of the air between the capacitor plates. On a cold dry day, the resistance of the air gap is 3× 1018 2, on a humid day, the resistance is 6 × 10° 2. How long will it take the capacitor voltage to dissipate to half its original value on each day? ... On the dry day, it will take seconds.
Determine the total capacitance, total charge, individual voltage drop and charges across each capacitor. Use two decimal places for your answer. Put your answer for the individual voltage and charge for each capacitor in a table for faster checking. Thank you! Here are the values for the capacitors: C1 = 55 C6 = 50 C2 = 25 C7 = 17 C3 = 49 C8 = 44 C4 = 22 C9 = 53 C5 = 45 C10 = 44
At 0-, no currrent flows through the capacitors because they are open, how did you combine the capacitors for the voltage divider since it is the capacitance value and not reactance, is it right? Can we just combine the capacitance value? Please explain. I did not understand..