This is in Electronics and devices. Solve the problem below with a complete solution. 3. The following figure shows the circuit for a full-wave bridge rectifier. Assume the diodes areNOT ideal.D1v, 10 sin(2x601) (±D2D4D3R(a) What is Vo when -2V< V₁ <2Vy? What is the state of D1, D2, D3, and D4 (ON or OFF)?(b) What is Vo when V₁ ≥ 2Vr? What is the state of D1, D2, D3, and D4 (ON or OFF)?(c) What is Vo when V₁ ≤ -2VY? What is the state of D1, D2, D3, and D4 (ON or OFF)?(d) Sketch Vo with respect to time.(e) If the diodes used were ideal, what is the DC value of the rectified output?(f) If the diodes used were ideal, what is the RMS value of the rectified output?

Since you have posted the questions with multiple subparts. So we are supposed to answer 1st 3…

3. The following figure shows the circuit for a full-wave bridge rectifier. Assume the diodes are NOT ideal. v, 10 sin(2x601) + D1 -✓ D2 D4 D3 R V (a) What is Vo when -2VY < V₁ <2VY? What is the state of D1, D2, D3, and D4 (ON or OFF)? (b) What is Vo when V₁ ≥ 2VY? What is the state of D1, D2, D3, and D4 (ON or OFF)? (c) What is Vo when V₁ <-2VY? What is the state of D1, D2, D3, and D4 (ON or OFF)?

3. The following figure shows the circuit for a full-wave bridge rectifier. Assume the diodes are NOT ideal. v, 10 sin(2x601) + D1 -✓ D2 D4 D3 R V (a) What is Vo when -2VY < V₁ <2VY? What is the state of D1, D2, D3, and D4 (ON or OFF)? (b) What is Vo when V₁ ≥ 2VY? What is the state of D1, D2, D3, and D4 (ON or OFF)? (c) What is Vo when V₁ <-2VY? What is the state of D1, D2, D3, and D4 (ON or OFF)?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
A diode circuit is given in the below figure, in which two diodes are connected in series and their saturation currents are Is1 =10-¹6 A and Is2 =10-¹4 A. If the applied source voltage is 1 V, calculate the currents IDI and ID2 and the voltage across each diode VDI and VD2. IDI Ī Vpl + D₂ VD2
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
For the circuit shown in the Figure, if the diodes are silicon diodes with VD(on)=0.7 V, and VIn=50 sin wt V, V1 =7 V and V2 =13 V, then the value of VOUT (p-p) is: R1 D, D2 VIN VOUT vi E v2= Ca. 19.4 V Ob. 17.4 V Cc. 15.4 V Cd. 21.4 V
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to tó. D1 D2 D3 22) tl: D. & D.. 23) t2: D. & D.. 24) t3: D. & D.. 25) t4: D. & D.. D4 D5 D6 26) t5: D. &D. 27) t6: D.AN A & D....... Vm cot t6
How do I calculate the dynamic resistance of a zener diode with the following set of values given please? The circuit in figure is the circuit in question I am trying to solve this for please. Vin(DC) = 10V vin(ac) = 0.05sin(wt) Vz(voltage of diode) = 4.5V R1 = 1000 ohms
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
Calculate the currents passing through the diodes D1 and D4 in the circuit given below. (All diodes are silicon).
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
2. Figure A.1 shows I-V characteristics of two diodes, namely A and B. Diode A has higher dynamic resistance than diode B. UTM &UT ID 4 5UTM 3TM UTM UTM &UTM 5 UTM & UTM UTM 3 UTM 03 TM 6 UT 0.68 (a) UTM VD Figure A.1 State one possible reason why the diodes have different knee voltage values. UTM OM & UTM 3 UTM & TM (b) Based on Figure A.1, identify the knee voltage of UTM" TM 5 UTde BE UTM