A 232-lb block is resting on a rough horizontal surface for which the coefficient of friction is 0.3. Determine the force P required to cause motion to impend if applied to the block downward at 39 degrees with the horizontal. P

Q: Calculate the bearing of a line joining the SW corner of the NE ¼, of the NE ¼ of Section 29 and the…

A: To find the bearing of a line joining the SW corner of the NE ¼, of the NE ¼ of Section 29 and the…

Q: Complete the following set of profile level notes and show the customary arithmetic check.

A: To complete set of profile level

Q: 90 Engineering Drawing الفصل الثالث شكل رقم 13 R20 40 35 55 9. 30

A: Providing Here the View for Front View, Top View and Left Side Views.

Q: 1/2x10ft

A: We are given: 1/2×10 ft   The given expression is equivalent to computing half the length of 10 f.

Q: x; ]] a» a» dz || X2 a3 a a33

A: For calculation assume,

Q: Line A B C 9. Fill in ONLY the seven (7) grayed blanks in the following form. Dep. Corrected…

A: Solution: Convert to whole circle bearing: Line Bearing Whole circle bearing AB N 57o 34' E 57o…

Q: Can you help me figure out the different symbols and how many of them are there and put them in…

A: Single Pole Switch Duplex Outlet Quadruplex Outlet Electrical Outlet Fan Outlet Wall Mounted…

Q: Draw the sectional front view (front section) and draw the orthographic projection (sideand top…

A: Asked: To draw the orthographic projection views of the given object.   The orthographic projection…

Q: (x+yc )dx - (xc ) dy こ0

A:

Q: Compute the DMD of Line 1-2

A: Answer : DMD ( Double Meridian Distance) of line 1-2 is     -30.

Q: Show the quadrants of a circle and within the circle show  S 30° W

A:

Q: complete the following set of profile level notes and show the customary arithmetic check.

A: Height of instrument method:HI=Elv+BMElvi+1=HIi-FS or ISExampleHI at BM-a:HI=234.51+1.24=235.75Elv…

Q: ONS B.S. H.I. F.S. LF.S. ELEVATIONS -a 1.24 234.51m 1.11 3.40 4.6 2.8 3.6 2.4 3.21 2.46 1.2 3.2 2.8…

A: Given profile levelling HI = elevation +   BS elevation = HI - FS or IFS given elevation of BM a =…

Q: GIVEN: = 43.6°, AB = 55.2m, Hi = 1.4m REQUIRED: H 38.66m 38.97m 39.47m 39.97 A Ø Hi H B

A: Given data:- The given angle, φ=43.6° The Length of AB is, 55.2 m The value of Hi, =1.4 m

Q: Consider the commercial steel pipe shown in (Figure 1). Determine the flow of methane at T = 68°F in…

A: Pressure Drop (ΔP) = 5 * 10^(-3) psiLength of the pipe (L) = 2600 ftDiameter of the pipe (D) = 1…

Q: ARSWer ls With reference to the units systems, One full circle equals 400 Grades 180 15 30 2 TT

A: One Full Circle equals to 400 GRADES  And also 2π radians and 360°

Q: A C L- (2) B "1-12- -L/2→ C x

A:

Q: RITING ITLED d. What is the difference in elevation between TP15 and TP30? (Ans.) e. What is the…

A:

Q: Determine the length of the dividing line which will divide the lot into two equal areas which is…

A:

Q: ") FOR THE GIVEN SECTION. (DImensions ore in mm ) a) Determnine the location of neutral as from the…

A:

Q: convert 284.366 decimal angle into degrees, minutes, and second.

A: Givend=284.3661Degree=60'1'=60''so1degree=3600''

Q: Assignm R= Station 18+26 18+00 17+00 16+00 15+68 3: For Arc 0 Deflection Angle (DMS) 0°0'0" Chord…

A: Horizontal Curve :  In order to transition between two tangent strips of road, a horizontal curve is…

Q: Complete the following set of profile level notes and show the customary arithmetic check.

A: Formula: Height of instrument methodHIi=Elevi+BSiElvi+1=HIi-FS or BSi+1example:at Station…

Q: For the two lane highway below, determine the distance required to transition pavement cross-slope…

A: Given Data:   Normal  cross slope is G=2%= 0.02   Super elevation is e=8%=0.08   Design speed is…

Q: Question #8 Determine the centerline length_(wall is 200 mm thick) 31500 8200 10250 19200 006E 000Z

A: NOTE : as per our guidelines we are supposed to answer only one question, kindly repost the another…

Q: LINES Line 1-2 Line 2-3 Line 3-4 Line 4-1 BEARINGS N 78° 07" E $10° 26' E $ 81°53' W N 10°05' W…

A:

Q: Q1: determaine the coordinates of the centeroid of the shaded area 20 40 50 20 40 30 140

A: The polar coordinate system is a method to calculate points in the system location by proper…

Q: Kindly solve this question under Measurement and Specifications for Civil Engineers.

A: Based on the information provided and the Contract Specifications, here's the takeoff for the…

Q: Find the area of each. Then put in square feet and square yards

A: Explanation(') means foot(") means inches1 square foot = 0.111 square yard1) Area of red rectangle =…

Q: Convert 36° 19' to decimal degree form.

A: Given data: θ=36∘19'

Q: How did you get -7.5x2+0.417x3 for M1? Thank you for answering.

A: The triangular load can be assumed to be superposition of a downward uniform load and upward…

Q: -20 +0.50 20/3

A:

Q: 9. Using cantilever method, determine the maximum absolute axial force in the column in kN due to…

A: Given data in question  Lateral loading Dimensions  Cantiler method  To find out  Axial forces in…

Q: 1. Calculate the total area of the given plan. Assume that all the dimensions are given in meter.…

A: Given plan

Q: х у The value of |2y + z y [2z + x [2x + y z is

A:

Q: St BS 0+00 3.54 0+10/ 0+20 1 1 1 1 I 2.994 2.044 0.171 00249 1.497 IS 3.269 2.966 Fs 1.845 1.840…

A:

Q: 11. Which IS codes gives details about elevators? A. O IS 27752 B. O IS 38665 C. O IS 14665 D. O IS…

A: IS code that gives details about elevators

Q: sanitary engineering  solve by hardy Cross method  k=8*f*L/pi*g*D^5 f=0.02 g=9.81 pi=e.14

A: Given data in question  Length of pipe  Diameter of pipe Constant value of f Acceleration due to…

Q: If Ax B = = A.B then the angle between A and B will be %3D a) п b) π/2 ) π/3 TE e) None of the above…

A: To find angle between A and B

Q: calculate R1,R2,R3

A:

Transportation Planning Process

A transport planning process is the process of defining future policies, objectives, investments, action plans and spatial planning projects to meet future transportation-related needs. As is being done today, it is a collaborative process that incorporates the views of a wide range of stakeholders including various central and local government agencies, state-owned enterprises and the private sector. Transport planners, planning organizations or federal agencies use a multidisciplinary approach to analyze a variety of alternatives and impact on the transportation system to contribute to profitable outcomes.