Draw the sectional front view (front section) and draw the orthographic projection (sideand top view) frothe figure Shown below

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A:

Q: How to solve the floor area and total floor area?

A: Floor Area is the the size or area of the floor in a structure or room.

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A: A truss is given as shown in the figure above and it has been asked in the question to determine the…

Q: A road is being designed for a speed of 110 km/hr on a horizontal curve with a super elevation of…

A: Given data- speed V=110 km/hrsuper elevation e=8%side friction f=0.10To Find-Minimum radius R

Q: If the all-red time required for pedestrian crossing at a two-phase signal is 12 s and the average…

A: given- 2 phase signal-red time=12 saverage normal flow for A qA=525average normal flow for B…

Q: A turbine receives water from a large reservoir and discharges the water into the atmosphere, if…

A:

Q: A tube well is constructed in a confined aquifer. The discharge of the tube well is 10 L/s, where…

A: Required :- Diameter of the well, dw

Q: 11-15. Determine the moment at B, then draw the moment diagram for each member of the frame. Assume…

A:

Q: Q3) Determine the depth and width at average and minimum flow and dimensions the weir plate of…

A:

Q: the distinct plane of oil-water contact and gas-oil contact?

A: For field development and estimation it is necessary to know the positions of fluid contacts. It is…

Q: A double-acting reciprocating pump having 2 a piston area of 0.1m² has a stroke 0.30 2 m long. The…

A: given- piston area A=0.1 m2stroke L=0.3 mdischarge Q=2.4 m2/min=2.4 60 m3/sN=45 rpmH=hs+hd=10 m

Q: Problem Set - 2: The simply supported steel beam is loaded by the 20 kN-m couple as shown in the…

A:

Q: The probability that the annual maximum flood discharge will exceed 25000 m³/s, at least once in…

A:

Q: A car moving down a sag curve having sloped of -3% and +2%. The head lamp is 0.80m above the road…

A:

Q: 1. In the structure below, members BF and AE are connected with a pin at D. Find the minimum…

A:

Q: 6- A cable, of uniform weight per unit length (w=1 kN/m), is suspended between two points A and B…

A:

Q: 12-18. Determine the moments at each joint of the frame, then draw the moment diagram for member…

A:

Q: extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 540 mm.…

A:

Q: A symmetrical parabolic curve passes through point A whose elevation is 23 23m at a distance of 54…

A: Correction in question:- As the elevation of PC is given as 22.56 m Hence, elevation of point A can…

Q: What is the Comparison or contrast of waste management of Solid and Liquid waste in the United…

A: Comparision involves definition  Classification  Functional Elements of solid waste management…

Q: A beam is simply supported on a span of 10 m. The beam supports a load of 15 kN/m on its entire…

A: Given Data  A simply supported span is given with the following data  Span length is 10 m  A…

Q: Design the most economical W14 column to carry a load of 1650k if Lx = 24' and Ly = 16'. Flx-pin…

A: Design of column W14 column P=1650 kN Lx=24'=609.6 mm Ly=16'=406.4 Fy=50ksi

Q: 4) Determine the minimum allowable height h of the beam shown in the figure if the bending stress is…

A: Given data  b = 80 mm  Allowable bending stress = 20 MPa

Q: A concentrated load of P acts on a simply supported beam of span L at a from the left support. The…

A: Given: A simply supported beamspan of beam is L,Load P is acting at L3 from the left support,

Q: Calculate the hydraulic conductivity of the soil in cm/sec. Determine the seepage velocity, in…

A:

Q: A propped cantilever beam having a span of 6 m is loaded with a uniformly distributed load of 12kN/m…

A: Disclaimer ''Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Problem Sets - 3: The cast iron inverted T-section supports two concentrated loads of magnitude P as…

A:

Q: 3. A rigid frame is subjected to a uniformly distributed load as shown in Fig. 3. 1) Find the…

A:

Q: 8. Design rectangular sections for the beams, loads, and p values shown. Beam weights are not…

A:

Q: What are the various measures of dispersion?

A:

Q: A 10 il load is uniformly cated by an aluminum alloy pipe with an outside diameter of 10 cm and…

A:

Q: Probl Compute gage pressure at the center of pipe. For solution use: (a)British Unit, (b)Standard…

A: To Determine Gauge pressure in the centre of the pipe. a) In British unit ( psi ) b) In SI unit (…

Q: The probability that the annual maximum flood discharge will exceed 25000 m³/s, at least once in…

A:

Q: Determine the seepage velocity, in cm/min, if the porosity of soil is 0.30

A:

Q: 4- For the beam shown in the figure (L=4m, EI=6000KN.m²). Using the differential equation El day dx4…

A: Given Data:L=4MW=90kNEI=6000kN.m2

Q: Q:Aura locand in the 18 a line if the bebine efficiency is 90%, what is the output brepower of the…

A:

Q: O and contains air at

A: we have to find out pressure at point A.

Q: 3. A project to extend irrigation canals into an area that was recently cleared of mahogany trees…

A:

Q: A floor sheathing is supported by 75 mm x 250 mm wooden joists of unknown spacing. The joist has an…

A: GIVEN DATA:-⇒Length of joist (L)= 3.75m⇒Floor load (w) = 4.75 kpa⇒Allowable bending stress (σallow)=…

Q: Problem Set - 3: For the overhanging beam shown, (a) derive the equation of the elastic curve; and…

A:

Q: 2. In the structure below, the vertical bar A has a modulus of elasticity of 210 GPa, a length of…

A:

Q: Consider a thin, flat, uniform, homogeneous rectangular plate of sides 1200 x 1500 mm, and mass 5…

A: Given Rectangular Plate of, Length, L = 1200 mm Breadth, B = 1500 mm Mass, M = 5 Kg

Q: Consider the timber beam shown below. The beam is made out of southern yellow pine, with an…

A: Given :

Q: Que in the far ellacy 90% what is the en gre utpote tatinete CH Don Lat La Com D GEOM Odon 14:02…

A:

Q: A cantilever type gate hinged at Q is shown in the figure. P and R are the centres of gravity of the…

A:

Q: Ex) Using The method of dimensions, derive an expression for rate of flow (CP) of liquid Through a…

A:

Q: Question Flow Using the Gap Method The single door shown in Figure 3.3 has the following dimensions:…

A:

Q: Q4: The pump is adding 7500W fluid power to the flow (toward J) in fig.(2). Find the flow in each…

A:

Q: For the truss shown: (a) Identify all zero force members (b) Determine the force in members AE and…

A:

Q: A plate 0.025 mm distant from a fixed plate moves at 60 cm/s and requires a force of 0.2 kgf/m² to…

A: given- distnace H=0.025 mm=0.0025 cmvelocity v=60 cm/sforce F=0.2 kgf/m2