") FOR THE GIVEN SECTION. (DImensions ore in mm ) a) Determnine the location of neutral as from the bottom of the bcom porallel to x - ais b) what 1s the moment 6F inertia about the neutral C) what the maxmum bunding Is stress M= so K m ? d) what is he mayim um shior stress if V = 25 KeN ?

Q: Using Mohr's cirlce method Determine: a) Average normal stress. Au b) Maximum and minimum stress. c)…

A:

Q: Inercise:- a A cylindrical rod 100 mm 12 mm diameter of long with is subjected to a 30000 N. Assumiy…

A: To choose the suitable material that satisfies the given elongation and reduction in diameter…

Q: Q.1/The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is…

A:

Q: Problem 3 in the steel structure shown, a 6-mm-diamter pin is used at D and 10-mm-diameter pins are…

A:

Q: If the beam is subjeded to a shear Compute the maximum shor stress b- Compute the shear stress 40 mm…

A: I = 200310312-170250312I = 275.16×106 mm4V = 40 kNQ = VAy¯Ib, whereV = Shear ForceA = Area above the…

Q: Assume that two 8-mm-diameter bolt joins the plates that are each 175 mm wide. The allowable…

A: Given, 2-8 mm diameter bolt width of plate= 175 mm Allowable bearing stress for plate=120 MPa…

Q: A solid shaft of circular cross-section is subjected to torque 7 which produces a maximum shear…

A:

Q: please someone answer this with complete solution thank you

A:

Q: 2- A 8teel podis streteke between fwo pugid walls ard carries a tensile Coad f GO0ON a C. If the…

A:

Q: For the element shown in figure. Calculate 1) Principle sthesses 2) Maximum in-plane shear stress 3)…

A:

Q: Q.1//The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is…

A: to find stress in each rod

Q: A belt i under van arcial thrust of 9.6 kN logether uwith va tranevowe force of 4.8 KN. 34 factor of…

A:

Q: 8.129 The rectangular plate is subjected to the pressure P Po-cos 2b Determine the resultant force…

A: It is required to calculate the resultant force of pressure and co-ordinates of point of…

Q: The pin-connected structure shown consists of a rigid bar ABCD and two axial members. Bar (1) is…

A:

Q: Find all reactions. Use Consistent deformation method.

A: It is asked to determine support reactions using Consistent deformation method. Given EI=constant

Q: Hw . the Cross- Sectiomal dimensions of a beam are Shown below. If the makimunm allowable berehing…

A:

Q: R14-9. The 60 strain ronette is mounted on a beam. The following readings are obtained for each…

A: Given: The 60 strain rosette is mounted on a beam. The following readings are obtained for each…

Q: 14-119. The smooth rigid-body cavity is filled with liquid G061-T6 aluminum. When cooled it is (0.3…

A: Given: The change in temperature is 110oC.

Q: Compute the displacements of the plate t = -20 Nm uoing a single quad ekmeent a 2m I(0,1) 4 (2,1)…

A: Cross section dimension at right end b(width) = 1m d(depth) = 0.5m

Q: * Detenmine the equation of the elantic ccerrves for the beams ohow in the following figune dere to…

A: Intensity of VDL at fixed support,  = 2WLSo, at x-x section, w' = 2WL2L - xWe know that, the…

Q: Q1// The compound wooden beam is connected together by a bolt at B. Assuming that the connections at…

A:

Q: beam AB supporting two concentrated loads P has a rectangular cross section of width b = 100 mm and…

A: The answer is found to be P=8.250 KN For explanation please refer to the attached solution, thanks

Q: Why the stress to the (X) or to the (Y) added partial differintial stress ?

A: ● Solution:-  As we know components of stress in stressed body generally vary from point to point…

Q: EX:- Analyze by the ConSistent defor mation.method the beaum Shown and than Draw S-F D and B-MD EI…

A: DS=re-2=3-2=1above beam is indeterminate to first degree then  considering reaction RB  as…

Q: cmonl *9-56. The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and…

A:

Q: A timber beam 150 mm wide by 250 mm deep is

A:

Q: 40 MPa 35 MPa 60 MPa

A:

Q: What shape Sheau foue woment is bending and caspectad

A: Assume the length of beam has 2 m. Taking moment at A, ∑MA=0Cy2-5222-125×123×1+1=0Cy=7.08 kN

Q: For the beam below find the normal stress at sections in point (B) and (C) 75 kN 35 kN 45 kN 85kN…

A: T oFind :-  normal stress at B and C in sections of the beam

Q: Dreive the equafion of f€]+the elasticity matrix EE]= 大サ (1++) (1-27) 1-2Y by, the finite element…

A:

Q: Evercise:- A cylindrical rod 100 mm diameter of 12 mm long with is subjected to a 30000 N. Assuming…

A: Given,Initial length of the rod, say L = 100 mmInitial diameter of the rod, say D = 12 mmTensile…

Q: Determine stress

A: Given data Load =P=30 KN Area=A=20 mm 2  Determine stress =?

Q: 3- Determine: 4m a) The stresses in the bars shown after a temperature rise of 96°C. Brone har…

A: Compressive Stress: when a load (P) is acting on the bar having cross-sectional area (A)which…

Q: E al = 70Gpa  E cu = 75 Gpa  fınd the max stress in both of tow materials in the picture

A: The composite structure is construct of more than one material this will increase the strength and…

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land.  Zoning is done or can be understood with the help of a site plan.