A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s.,= 345 MPa) for the C-frame material. Calculate the maximum bending tensile stress in MPg? 18 mm 38 mm 13 kN 10 mm -90 mm 25 mm A At

A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s.,= 345 MPa) for the C-frame material. Calculate the maximum bending tensile stress in MPg? 18 mm 38 mm 13 kN 10 mm -90 mm 25 mm A At

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.9P: A propeller shaft of solid circular cross section and diameter d is spliced by a collar of the same...

See similar textbooks

Similar questions

Repeat Problem 2.3-18, but assume that the bar is made of copper alloy. Calculate the displacements SBand Scif P = 50 kips, L = 5 ft = 3/5 in., b1= 2.75 in., b2= 3 in., and E = 16,000 ksi.
Repeat Problem 2.3-4, but now include the weight of the bar. Sec Table 1.1 in Appendix I for the weight density of steel.
A stepped bar with a hole (see figure) has widths h = 2.4 in. and c = 1.6 in. The fillets have radii equal to 0.2 in. What is the diameter d max of the largest hole that can be drilled through the bar without reducing the load-carrying capacity?
A propeller shaft of solid circular cross section and diameter d is spliced by a collar of the same material (see figure). The collar is securely bonded to both parts of the shaft. What should be the minimum outer diameter dyof the collar in order that the splice can transmit the same power as the solid shaft?
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
PROBLEM:1 A gas engine valve spring is to have a mean diameter of 55 mm. The maximum load it will have to sustain is 584 N with a corresponding deflection of 7.18 mm. The spring is to be made of tempered wire. Since the material is to be subjected to repeated loading and fatigue must be considered a low working stress of 650 N/mm? will be used. Find the size for wire and number of coils used. Take modulus of rigidity as 0.84 x 105 N/mm? .Assume the spring coil is squared and ground. Take shear stress Concentration factor as 1.15.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
1. A component in an aircraft flap actuator, shown in Figure 1, can be adequately modelled as a cylindrical bar subjected to a compressive axial force of 8 kN, a bending moment of 55 Nm and a torque of 30 Nm. It is to be manufactured of a 20 mm diameter solid bar of 7075-T6 aluminium alloy. FLAP ACTUATOR (a) (b) (c) (d) (e) POWER SCHEW JACK CARRIAGE -FAPERON BALL NUT FLAP NOSE ROLLER BEAM FITTING CARRIAGE ROLLER -COLLAPSIBLE DOOK Figure 1: Aircraft Flap Actuator At a critical point on the bar surface, determine the value of the, (1) compressive direct stress, (ii) (iii) tensile bending stress, and shear stress. Indicate on a representative element in 2-D cartesian coordinates the stresses calculated in (a). Determine the principal stresses and the maximum shear stress at the point. Sketch the Mohr's stress circle representing the stress system and clearly mark on it the principal stress values calculated in (c) above and the direction (angle) of the maximum principal stress (0₁) with…
Calculate the wire diameter of a helical spring using Wahl's factor if the load applied is 130 lb and spring index is 8, if the maximum shearing stress is 50 ksi.
A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s,,= 345 MPa) for %3D the C-frame material. Calculate the bending moment about the centroidal axis upto 3 digits after decimal point in kN.m 18 mm 38 mm 10 mm 13 kN 25 mm 00 mm 10 mm
1. A component in an aircraft flap actuator, shown in Figure 1, can be adequately modelled as a cylindrical bar subjected to a compressive axial force of 8 kN, a bending moment of 55 Nm and a torque of 30 Nm. It is to be manufactured of a 20 mm diameter solid bar of 7075-T6 aluminium alloy. FLAP ACTUATOR (a) (b) (c) POWER SCREW JACK CARRIAGE (ii) FLAPERON BALL NUT FLAP NOSE ROLLER BEAM FITTING CARRIAGE ROLLER a bending stress, and -Flap actuator. Figure 1 At a point on the shaft surface, determine the value of the, (i) compressive stress, FLAP -COLLAPSIBLE DOCK (iii) shear stress. Indicate on a representative element in 2-D Cartesian Coordinates the stresses calculated in (a). Determine the principal stresses at the point.
A solid steel shaft of radius b is to be pressed into a wrought iron hub of outer radius c and length L. L is also the length of engagement of the shaft and hub. Calculate (a) the interface pressure in MPa; (b) the force needed for the press fit in kN; and (c) the torque capacity of the assembly in kN-m. Let b = 50mm, c = 100 mm, L= 180 mm, Es = 210 GPa, Eiron = 190 GPa, f = 0.15. Assume that the maximum allowable tangential stress in the assembly is 25 MPa.