Design a muff coupling to connect two shafts. The power to be transmitted is 27kW at a shaft speed of 440 rpm. The shaft and the key are made of same material and the allowable shear and the crushing stresses are 37 & 79 N/mm2 respectively. Calculate

Design a muff coupling to connect two shafts. The power to be transmitted is 27kW at a shaft speed of 440 rpm. The shaft and the key are made of same material and the allowable shear and the crushing stresses are 37 & 79 N/mm2 respectively. Calculate

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Design a muff coupling to connect shaft transmitting 40kw at 120rpm .the permissible shear and crushing stresses for the shaft and the key material are 30Mpa and 80Mpa respectively .the material for muff is cast iron with permissible shear stress is 15Mpa .assume that maximum torque transmitted is 25 percent greater than mean torque.
(4) An electric motor purchased by your employer surprisingly arrived without a keyway in the shaft. The motor has power rating of 7.5kW & 1,800rpm & has a shaft of Ø17mm. It will be used to drive a centrifugal pump using cast iron sheave. Design the square key to be used in the assembly based on maximum bearing & shearing stresses of 580MPa & 370MPa, respectively, and factor of safety of 5.
A flanged coupling rotating at 400 rpm have 4 steel bolts evenly tightened around a 100 mm bolt circle. What diameter of bolt should be used if the power transmitted is 26.5 kW and the design shearing stress of the bolt is 12 MPa?
(b)Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also gIven pitch = 8mm and coefficient of friction is 0.15?
A shaft/hub connection transmits a torque C =60N.m. We use a rectangular key (W=14mm x H=9mm) with a length of 30mm for a 45mm diameter shaft. Calculate the force exerted on the key.Calculate the compressive and shear stress.
I want proper solution don't copy from others solution I will report. flange coupling connects two 50 mm diameter lengths of commercial shafting. The coupling flanges are bolted together with four bolts of the same material as the shaft. The bolts are set in clearance holes. The diameter of the bolt circle is 240 mm and the flange thickness is 22 mm, (1) Determine the minimum bolt diameter required to transmit the same torque that the shaft can transmit.
A gear drive is required to transmit a maximum power of 22.5KW, the velocity ratio is 1:2 and the rpm of the pinion is 200 .the approximate center distance between the shaft may be taken as 600mm.the teeth has 20°stub involute profile.the static stress for the gear material ( which is cast iron ) may be taken as 60MPa and face width as 10 times the module.find the module, face width and number of teeth on each gear.Check the design for dynamic and wear loads. The deformation factor in the buckling equation may be taken as 80 and material combination factor for the wear as 1.4
3. Find the power that can be safely transmitted by a flange type shaft coupling, if it has four equally spaced studs all at a radius of 50 mm from the shaft centre. The mean stud diameters are 12.5 mm, and each stud has a maximum safe working shear stress of 86 MPa. The shaft rotates at 3600 rpm.
Q.1 Design a compression coupling for a shaft to transmit 2000 N-m. The allowable shear stress for the shaft and key is 50 MPa and the number of bolts connecting the two halves are 6. The permissible tensile stress for the bolt material is 90 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3.
A 16 in. diameter motor pulley is running at 600 rpm with a 6 in diameter shaft transmitting power to an agricultural locomotive. If the dimensions of the square key is 0.5 x 3 in, what is the maximum force in the pulley’s belt that can be transmitted if the shear stress is limited to 8500 psi and bearing stress limited to 4000 psi?
A rigid coupling with 30 inches of bolt circle diameter transmits a torque of 18,000 lb-in. The coupling material has a yield strength of 90,000 psi. The coupling is fastened by six bolts. Assume design factor of N=3 Calculate the diameter of each bolt.
Parvinbhai