You are asked to study the distribution of shear stress and the angular deflection in solid and hollow circular shafts and give a report based following calculations. A shaft 50 mm diameter and 0.7m long is subjected to a torque of 1350 calculate the shear stress and the angle of twist. Take G= 90 GPa. Repeat the previous problem considering the shaft is hollow with an internal diameter of 30 mm.

You are asked to study the distribution of shear stress and the angular deflection in solid and hollow circular shafts and give a report based following calculations. A shaft 50 mm diameter and 0.7m long is subjected to a torque of 1350 calculate the shear stress and the angle of twist. Take G= 90 GPa. Repeat the previous problem considering the shaft is hollow with an internal diameter of 30 mm.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Similar questions

What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A steel shaft is transmitting 55 hp at 1200 rpm. The nature of the load and the type of service of the shaft is such that the allowance shearing stress based on the pure tension is 4000 psi. (MAXIMUM TORSIONAL STRESS AND ANGLE OF TWIST FOR A SOLID SHAFT) Calculate the diameter of the shaft to the nearest commercial size of the shafting. 2.Calculate the torsional deflection of the shaft in degree for one foot length of the shaft.
What is the minimum diameter of a solid steel shaft that will not twist through more than 3 in a 6 m length when subjected to a torque of 12 kN-m? (b) what maximum stress is developed in the shaft? Use G-83 GPa. Remember the angle of twist (0) calculated using the equations is in radians. Incorrect solution will be downvoted
1. A solid circular shaft transmits 75 kW power at 200 rpm. Calculate the diameter of the shaft and the maximum shear stress acting on it, if the twist in the shaft is not exceeding 1° in 2 m length of the shaft. Take modulus of rigidity as 102 GPa.
Two designs for a shaft are being considered. Both have an outside diameter of 60 m and are 800 mm long. One is solid but the other is hollow with an internal diameter of 40 mm. Both are made from steel (G=70 GPa). Compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of T N. m. Use the last THREE digit of your ID Number for the missing Torque (T). 575
2. Solve the following problem Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Critically evaluate and compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque ofT 171N.m the missing Torque 171(T).
A hollow shaft must transmit 1400 kW at 180 rpm. The outside diameter must be 1.6 times the inside diameter. The maximum torque is 30% more than the mean torque. Calculate: 1. The diameters of the hollow shaft if the allowable stress is 200 MPa. 2. The diameter of the solid shaft if the allowable stress is 200 MPa.
Compute the torsional shear stress in a circular shaftwith a diameter of 50 mm that is subjected to a torqueof 800 Nm
A uniform shaft of diameter 30 mm is subject to a 60 N of tangential force. Calculate the shear stress induced in the shaft.
Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of 796 N. m.