A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s,=345 MPa) for %3D the C-frame material. Calculate the bending moment about the centroidal axis upto 3 digits after decimal point in kN.m

A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s,=345 MPa) for %3D the C-frame material. Calculate the bending moment about the centroidal axis upto 3 digits after decimal point in kN.m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.1P: A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel...

See similar textbooks

Similar questions

A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s.,= 345 MPa) for the C-frame material. Calculate the location of neutral axis upto 2 digits after decimal point in mm? 18 mm 38 mm 13 kN 1 10 mm A* 25 mm YA -90 mm 10 mm
1. A component in an aircraft flap actuator, shown in Figure 1, can be adequately modelled as a cylindrical bar subjected to a compressive axial force of 8 kN, a bending moment of 55 Nm and a torque of 30 Nm. It is to be manufactured of a 20 mm diameter solid bar of 7075-T6 aluminium alloy. FLAP ACTUATOR (a) (b) (c) POWER SCREW JACK CARRIAGE (ii) FLAPERON BALL NUT FLAP NOSE ROLLER BEAM FITTING CARRIAGE ROLLER a bending stress, and -Flap actuator. Figure 1 At a point on the shaft surface, determine the value of the, (i) compressive stress, FLAP -COLLAPSIBLE DOCK (iii) shear stress. Indicate on a representative element in 2-D Cartesian Coordinates the stresses calculated in (a). Determine the principal stresses at the point.
1. A component in an aircraft flap actuator, shown in Figure 1, can be adequately modelled as a cylindrical bar subjected to a compressive axial force of 8 kN, a bending moment of 55 Nm and a torque of 30 Nm. It is to be manufactured of a 20 mm diameter solid bar of 7075-T6 aluminium alloy. FLAP ACTUATOR (a) (b) (c) (d) (e) POWER SCHEW JACK CARRIAGE -FAPERON BALL NUT FLAP NOSE ROLLER BEAM FITTING CARRIAGE ROLLER -COLLAPSIBLE DOOK Figure 1: Aircraft Flap Actuator At a critical point on the bar surface, determine the value of the, (1) compressive direct stress, (ii) (iii) tensile bending stress, and shear stress. Indicate on a representative element in 2-D cartesian coordinates the stresses calculated in (a). Determine the principal stresses and the maximum shear stress at the point. Sketch the Mohr's stress circle representing the stress system and clearly mark on it the principal stress values calculated in (c) above and the direction (angle) of the maximum principal stress (0₁) with…
A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s.,= 345 MPa) for the C-frame material. Calculate the maximum bending tensile stress in MPa? 18 mm 38 mm 13 kN 25 mm 1 10 mm 90 mm A+ 10 mm
A solid steel shaft of radius b is to be pressed into a wrought iron hub of outer radius c and length L. L is also the length of engagement of the shaft and hub. Calculate (a) the interface pressure in MPa; (b) the force needed for the press fit in kN; and (c) the torque capacity of the assembly in kN-m. Let b = 50mm, c = 100 mm, L= 180 mm, Es = 210 GPa, Eiron = 190 GPa, f = 0.15. Assume that the maximum allowable tangential stress in the assembly is 25 MPa.
(9) A Mercedes Benz gas engine valve spring should not exceed to a cylindrical space of 1¾-in in diameter. The spring index is 6.0 & the maximum load it will have to sustain is l00lb with corresponding deflection of ½-in. The spring is subjected to repeated loading & fatigue must be considered, a low working stress of 40,110psi will be used. Determine: (a) the diameter of wire based on commercial sizes; (b) the number of coils.
Write down the Uniaxial, Bending and Torsional loading rigidity terms, and specify thename of their components.
A helical compression spring is made of no. 16 music wire. The outside coil diameter of the spring is 1.5 in. The ends are Plain end, ground and there are 13 total turns. (a) Estimate the torsional yield strength of the wire. (b) Estimate the static load corresponding to the yield strength. (c) Estimate the scale of the spring. (d) Estimate the deflection that would be caused by the load in part (b). (e) Estimate the solid length of the spring. ( f ) What length should the spring be to ensure that when it is compressed solid and then released, there will be no permanent change in the free length? (g) Given the length found in part ( f ), is buckling a possibility? (h) What is the pitch of the body coil?
3. A close coil helical spring is to have a mean coil diameter to wire diameter ratio of 10:1 to. The stiffness of the spring is to be 20 N/mm. The spring will carry an axial load of 500 N and the maximum shearing stress is not to exceed 80 MPa. Calculate the diameter of wire and coil, number of coils and the deflection under the Load. (G = 84 GPa).
A forged steel bar, 50 mm in diameter, is subjected to a reversed bending stress of 250 MPa. The bar is made of 40 C8 with ultimate strength of 600 MPa. Calculate the endurance limit and life of the bar. Consider 90% reliability.