An ideal gas flows isentropically through a converging-diverging nozzle. At a section in the converging portion of the nozzle, and A₁ = 0.1 m², p₁ = 600 kPa(abs), T₁ = 20°C, and Ma₁ = 0.6. For section (2) in the diverging part of the nozzle, determine (a)A2, (b)p2, and (c)T₂ if Ma2 = 2.8 and the gas is air.

An ideal gas flows isentropically through a converging-diverging nozzle. At a section in the converging portion of the nozzle, and A₁ = 0.1 m², p₁ = 600 kPa(abs), T₁ = 20°C, and Ma₁ = 0.6. For section (2) in the diverging part of the nozzle, determine (a)A2, (b)p2, and (c)T₂ if Ma2 = 2.8 and the gas is air.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The converging-diverging nozzle(as shown in the figure given below) expands and accelerates dry air to supersonic speeds at the exit where p2 = 8 kPa and T₂ = 240 K. At the throat, p₁ = 284 kPa, T₁= 665 K, and V₁ = 495 m/s. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Air- D₁ = 1 cm Kg/s D₂ = 2.5 cm Determine the mass flow for a steady compressible flow of an ideal gas.
A large vessel contains compressed air at To = 350 K and Po = 2 bar. A converging-diverging nozzle is attached to the vessel to discharge air. The throat area of the nozzle is 200 cm2. At the exit, the pressure is 20 kPa and the flow is supersonic. Answer the followings:
A sample of steam is at a pressure of 300 kPa (x=0.75). Solve for its entropy.
Homework 2: Ten kilograms per second of air is flowing in an adiabatic system. At one section the pressure is 2.0 x 10° N/m², the temperature is 650°C, and the area is 50 cm?. At a downstream section M2 = 1.2. (a) Sketch the general shape of the system. (b) Find A2 if the flow is frictionless. (c) Find A2 if there is an entropy change between these two sections of 42 J/kg-K.
3. Show that for an isothermal compressible flow, 1 др рд =-V.V
(b) Air flows through a cylindrical duct at a rate of 2.3 kg/s. Friction between air and the duct and friction within air can be neglected. The diameter of the duct is 10cm and the air temperature and pressure at the inlet are T₁ 450 K and P₁ = 200 kPa. If the Mach number at the exit is Ma2 determine the rate of heat transfer and the pressure difference across the duct. The constant pressure specific heat of air is cp = 1.005 kJ/kg-K. The gas constant of air is R = 0.287 kJ/kg-K and assume k = 1.4. -
100% High pressure water and compressed air are delivered to some operating rooms. Bored one day, with no patients around, you take the cap off the nozzle to see what would happen. Water flows through the vertical pipe and nozzle and then exhausts into the air as shown in the diagram. The water pressure in the pipe at position 1 is 3 atm. The pressure when the water discharges to the air is 1 atm. Position 2 identifies the nozzle, 0.75 m above position 1, where the water flow has been constricted from an 8-cm diameter pipe to a 3-cm diameter nozzle. Assume that the free jet remains a stream of water with a 3-cm diameter. Assume no friction losses. Free jet -3 cm diameter 0.75 m a) Determine the mass flow rate of water through pipe at position 1 in kg/s. 3 atm 8 cm diameter b) Determine the height, h, the water jet can rise. c) Calculate the friction factor inside the 8-cm pipe and determine if the assumptions of negligible friction losses was reasonable. Water AR d 128 PM 10/3/2021…
Four pounds of air gain 0.491 Btu/°R of entropy during a nonflow isothermal process. If p1 = 120 psia and V2 = 42.5 ft³, find (a) V1 (ft³) and T1 (°R), (b) Wn (Btu), and (c) Q (Btu). And draw the P-V and T-S diagrams
Problem (6.1) Steam at 1.8 MPa and 275 °C expands through a convergent- divergent nozzle to 0.1 MPa. If there is 10 % loss in energy between the throat and the nozzle exit and the vapor flow rate is 0.5 kg/s, determine the cross- sectional area of the throat and the nozzle exit.
Air is flowing in a convergent nozzle. At a particular location within the nozzle the pressure is 280 kPa, the stream temperature is 345 K. and the velocity is 150 m/s. If the cross-sectional area at this location is 9.29 x 103 m², find: (a) The Mach number at this location, (b) The stagnation temperature and pressure. (c) The area, pressure, and temperature at the exit where M-1.0. (d) The mass rate of flow for the nozzle. Indicate any assumptions you may make and the source of data used in the solution.
Consider the two flows through identical nozzles sketched below. If the reservoir pressures and temperature are the same for the two flows, calculate the ratio of the mass flow rates at the exits of the nozzles, m,/m, . Me >d0 At Ae/At=4 M-1 Me
2. Carbon dioxide gas (CO2) flows adiabatically along a duct. At station 1 the static pressure P₁=120 kPa and the static temperature T1= 120 oC. At station 2 further along the duct the static pressurep2=75 kPa and the velocity C 2= 150 m/s.Determine (1) the Mach number M 2 (2) the stagnation pressure poz (3) stagnationtemperature Toz (4) the Mach number M 1 For CO 2 take R = 188 J/(kg K) and K = 1.30.