420 ohm 30 V Voltage 1,(max) = 80 mA 0.6 V 2.2 kohm Vp-out Vp-in Zener Current Answer the following question according to the above. Remember Kirchhoff's laws when making your calculations in this question. According to the given graph, how many volts is the voltage value on this Zener Diode when it is on reverse supply?

420 ohm 30 V Voltage 1,(max) = 80 mA 0.6 V 2.2 kohm Vp-out Vp-in Zener Current Answer the following question according to the above. Remember Kirchhoff's laws when making your calculations in this question. According to the given graph, how many volts is the voltage value on this Zener Diode when it is on reverse supply?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
C. In the circuit shown below the knee current for the ideal Zener diode is 10 mA Calculate the minimum value of load resistance RL in order to maintain 5 volts across the load resistance RL 2. WW-
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to tó. D1 D2 D3 22) tl: D. & D.. 23) t2: D. & D.. 24) t3: D. & D.. 25) t4: D. & D.. D4 D5 D6 26) t5: D. &D. 27) t6: D.AN A & D....... Vm cot t6
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
Calculate the voltage and current of the diode in the figure for each of the diode's models. In each case, determine the voltage across the resistor. Additionally, in each case, determine the diode's power. Assume that Rb is ten ohms.
Q1/Consider the circuit in Figure with a transformer of 10:1 transformation ratio and the diodes are silicon. a) What type of circuit is this? (b) What is the total peak secondary voltage? (c) Find the voltage value across the resistor (d) Sketch the voltage waveform across RL (e) What is the PIV for each diode? D3 D 120 V Pisez) Vpouo D D 10 kn lleee
How is Zener diode connected into a circuit? What determines the voltage at which a Zener diode break down? What considerations go into determining the power dissipation rating of a Zener diode? Draw a label the schematic symbol used to represent a Zener diode What determines the maximum Zener current of a Zener diode? What is the difference between the maximum Zener current and the reverse current for a Zener diode? What does a positive Zener voltage temperature coefficient signify? What does a negative Zener voltage temperature coefficient signify? How can a Zener diode be temperature compensated?
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
For the rectifier in the figure below, state the conduction sequence of the diodes for periods t1 to t6.1. t1: D...... & D.......2. t2: D...... & D.......3. t3: D...... & D.......4. t4: D...... & D.......5. t5: D...... & D.......6. t6: D...... & D......