What should be the value of Vi, if we have a Zener Diode with a breakdown voltage of 6.2 volts and a resistance of 1k ohms and a voltage reading ranging from 7.5 to 7.8 volts at 21ms on the simulation graph. ZenerDiode Vout V1 R1 ´1k 21ms 7 Draft11 Cursor 1 Vivout) Horz: 21.00271ms Vert: 7.7706735V Cursor 2 Horz - N/A- Vert -N/A-- Dif (Cursor2 - Cursor1) Horz: -- N/A- Vert N/A-- Freg - N/A- Slope N/A--

What should be the value of Vi, if we have a Zener Diode with a breakdown voltage of 6.2 volts and a resistance of 1k ohms and a voltage reading ranging from 7.5 to 7.8 volts at 21ms on the simulation graph. ZenerDiode Vout V1 R1 ´1k 21ms 7 Draft11 Cursor 1 Vivout) Horz: 21.00271ms Vert: 7.7706735V Cursor 2 Horz - N/A- Vert -N/A-- Dif (Cursor2 - Cursor1) Horz: -- N/A- Vert N/A-- Freg - N/A- Slope N/A--

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit shown below, the diode cut in voltage is Vy0.7V. Th value of I, varies over the range 0 s l, s 6mA. The Value of R-2.4kn and the value of Ve 4.8V Vo At which value of l, does the diode turn on O a.2.292 mA b. 1.833 mA c. 2.865 mA O d. 1.467 mA If l = 2.1mA, What is the value of Vo O a. 5.04 V O b. 4.03 V O c 6.3 V O d. 3.23 V If l= 1.6mA, What is the value of lo O a. 1.917 mA b. 0 mA O c 0.639 mA O d. 1.278 mA EO o
JAE To sketch the characteristic curve of the diode you need to vary voltages on diode and measure current flowing during forward and reverse bias condition. Fill up the table below using circuit shown and vary battery voltages. Measure voltage and current of diode then sketch the graph. Voltage X axis and Current Y axis. A Battery Diode voltage Voltage 0.1V 0.3V 0.5V 0.7V 1.0V 2.0V 3.0V 10.0V Diode Current Forward Bias Condition +||| V Battery Diode Voltage 0.1V 0.5V 2.0V 5.0v 10v 20V 25V 30V Voltage Note: used any electronics software to perform this activity Reverse Bias Condition Diode Current ELECTRONICS ENGINEERING (ECE) DEPARTMENT SINCE VIT
In reference to the output waveform below and using ideal diode model: Vout +7.5V -3.5V a. Analyze the behavior of the circuit and fill up the table below. Vin Diode state Vout (FB or RB) +6V OV -3V -6V b. Draw the clipper circuit that will produce the given output waveform.
I need short answer, please
Consider the circuit.a. What type of circuit is this?b. What is the total peak secondary voltage?c. Find the peak voltage across each half of the secondary.d. Sketch the voltage waveform across RL.e. What is the peak current through each diode?f. What is the PIV for each diode?
Draw the characterstic r-l for silicon diode in the forward bais and explain it.
What should be the value of Vi, if we have a Zener Diode with a breakdown voltage of 6.2 volts and a resistance of 1k ohms and a voltage reading ranging from 7.5 to 7.8 volts at 21ms on the simulation graph .
Make the described voltage multiplier circuit, determine the voltage charge in each capacitor, and the output voltage of the circuit. Plot the output waveform in proper phase alignment with the input voltage. Indicate the peak values with the support of your solutions. Use silicon diodes in your analysis and an input V=10 Vrms. a) Half-wave voltage doubler b.) Full-wave voltage doubler
Q-3. Draw 1-V characteristics of 5 V silicon zener diode (Vz-5V) and show its parameters V Vz, Izx. Izs, Izm on the curve. Q-4. Determine the range of Road (Rmin, Rmax) that will maintain Vz at 5 volts for the circuit given below. Rs m 1.0kg V1 40 V Pzm=150mw
Design the Clipper-Clamper circuit to perform the output waveform shown in figure below.
Answr all the questions one by one and solve all the unknown values giving all the correct details Let the last digit of the ID = 9
What are the peak voltage values for both half cycles of the output waveform. V=35sin(wt). Use modified ideal diode model (Va=0.7V) for diodes. 5 k2 Z1 Vo Vi 20-V Zeners Z2 O34.30V, -34.30V O35.70V, -35.70V O 17.60V, -17.15V O35V, -35.00V OOv,oV Clear my choice