Can you answer the question by explaining step by step and explaining why you used that formula or calculations in details please. Thanks a lot. 2) Consider a two terminal semiconductor diode a) Calculate the thermal voltage of a diode at room temperature about 27oC b) Calculate diode dynamic resistance in case of 13 mA diode current. (Boltzman’s constant is 1.38x10-23 J/K, and magnitude of electron charge is 1,6X10-19 C)

Can you answer the question by explaining step by step and explaining why you used that formula or calculations in details please. Thanks a lot. 2) Consider a two terminal semiconductor diode a) Calculate the thermal voltage of a diode at room temperature about 27oC b) Calculate diode dynamic resistance in case of 13 mA diode current. (Boltzman’s constant is 1.38x10-23 J/K, and magnitude of electron charge is 1,6X10-19 C)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
Consider the circuit shown in Figure 2. The cut-in voltage of each diode is . Let and assume both diodes are conducting. Determine if this is a valid assumption and explain your answer. And calculate the values of IR, ID, Ip2, and V.. Rj =1.7 kQ ww VB =1 V D1 Dz R2D 4 kQ Figure 2
A. In your own words and with the aid of suitable diagrams, describe the following: a) The zener diode and its characteristics. b) Design a limitter circuit using diodes to limit the output voltage to 4.7V during the positive signwave and to -6.7V in the negative signwave. B. Consider the following circuit. Suppose that diode D1 is ideal. a) Give the state of the diode D1: conductive or blocking. Explain. b) Calculate the current flowing through D1. c) Calculate the voltage VR2 across the resistance R2. 1kQ D1 R1 R2 1) ImA 10V 4KQ C. In the circuit shown below the knee current for the ideal Zener diode is 10 mA. Calculate the minimum value of load resistance RL in order to maintain 5 volts across the load resistance RL. 1002 IL 10V V, = 5V A R
There are three diode models namely (i) the exponential, (ii) ideal and (iii) the constant voltage source. a) Please define each model and provide the factors that influence the choice of a diode model when analyzing a circuit ? b) Please provide sketches of the I-V characteristic of each model.
Assuming that the diodes are ideal, determine whether each diode is ON (short circuit) or OFF (open circuit) and find the quantities indicated as V and I on the circuits below. Show guesses and verification work.
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
In your own words and with the aid of suitable diagrams, describe the following: Explain what the barrier potential is and how it is developed in pn junction diode. What is the typical value of the barrier potential for a silicon diode?
1. Determine the diode current (in Ampere) at 90°C for a silicon diode with reverse saturation current of 90 nanoAmpere and an applied forward bias of 0.5 volts. a. The value of k is (put values only) b. The temperature in Kelvin is (put values only, put up to 2 decimal places) c. The diode current (in Ampere) is : (put values only, put up to 6 decimal places)
4. If the diode is open in the circuit, the load voltage is? 5. If the resistor is ungrounded in the circuit, the voltage measured with a DMM between the top of the resistor and ground is closest to? 6. The load voltage measures 12 V in the circuit. The trouble may be? 7. Using the third approximation in the circuit, how low must R, be before the diode's bulk resistance must be considered? + Vs RL 1 k2 12 V Figure
a) What is n-type semiconductor materials? What are the majority and the minority cariers? b) What is p-type semiconductor materials? What are the majority and the minority cariers? c) What is depletion region of a p-n junction diode? d) Describe in your own words the forward-bias and reverse- bias conditions of a p-n junction diode. e) Draw a Diode Symbol and label the anode and the cathode. Si Ge 2 ka f) Find V, in the circuit shown in +20 V 2 k2 15V Fig. Fuad Al-Mannai EENG261 Page 1
Determine the diode current (in Ampere) at 70°C for a silicon diode with reverse saturation current 70 nanoAmpere and an applied forward bias of 0.8 volts. The constant k value is: The Temperature (in Kelvin) is: The Diode current (in Ampere) is: