4 VIV50 45 40 35 3025 2015 105 0distance [cm]Zo= 602ZLA 60 lossless line terminated by load Zz has a voltage wave as shown in the figure above.Find the standing wave ratios, the load reflection coefficient I' (magnitude and phase,,), and the load ZL--Use numbers when answering, rounding to the tenths in the format 0.0-Input your answer in the specified units for each parameterS= type your answer...[degrees]|T|=type your answer...Or=type your answer...ZL=type your answer...+j type your answer...[N]

Please go through the below attachments for a detailed explanation. If you have any queries, please…

Answered: 4 V IV 50 45 40 35 30 25 20 15 10 5 0…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem 13.6P

See similar textbooks

Similar questions

7- DC Chopper with output voltage of 120V and input voltage of 80V and output power of 240W. Assume lossless chopper. The average inductance current IL is * 2.6 A 3.0A 4.3A 8- taking into account obtained duty cycle from previous task, the needed : capacitor for realizing 1% ripples at frequency of 10kHz is? * ?? 55.56 uF O 13. 34 uF 92.44 uF
The corresponding R function for teh PMF is __________.
A 702 high-frequency lossless line is used at a frequency where 2 = 80cm with a load of 140+j91 2 a. Calculate the reflection coefficient and the SWR b. Determine the distance to the first voltage minimum from the load c. Determine the distance to the first voltage maximum from the load d. Calculate the impedance at the point where maximum voltages occur
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
30) In a lightly loaded long distance EHV lines, line loading is and has a power factor: (A) Capacitive, lagging. (B) Capacitive, leading (C) Inductive, lagging (D) Inductive, leading. please contact me in whatsapp +962782974574
Ideally, a dc load line is a straight line drawn on collector characteristic curves between which of the following? Please select one: a. Q Point and shear b. Q Point and saturation c. V_CE (interrupt) and I_C (sat) d. I_b = 0 and I_B = I_C/ß_DC
8. A transmission line has a characteristic impedance of 500 and a resistance of 0.1 02/m. If the line is distortion less, the attenuation constant (in Np/m) is (a) 500 (b) 5 (c) 0.014 (d) 0.002
5. Two cascaded lossless transmission lines are terminated by Z₁-2502, as shown below.. a) Calculate the reflection coefficient and the standing wave ratio at the load, i.e., the CC' terminal. b) Determine the characteristic impedance of the quarter-wavelength transformer, Zol, to match the cascaded line to a 6492 generator. B A- A'. Zol 11= 2/4 B' Zo2=75 92 12=32/4 C C ZL=2592
b) A 6052 characteristic impedance transmission line is fed by a DC source of 100V with an internal resistance of 4002. The line is 200m long and has a dielectric constant of 2.25. The load impedance is 12002. Calculate: i. The load reflection coefficient. ii. The source reflection coefficient. iii. What is the voltage at the source terminals just before AND just after 2us?
One circuit of a single-phase transmission line is composed of three solid 0.12" radius wires. The return circuit is composed of two 0.15" radius wires. Find the inductance of the complete line in mH/mi. The distance between wires are 40" horizontally and 25" vertically. A. 2.54 mH/mi B. 2.478 mH/mi C. 2.488 mH/mi D. 2.567 mH/mi Provide Clear Explaination
The capacitance of a single phase two-wire transmission line depends on: Select one: a. All the above O b. the material of cables c. the radius of cables d. the distance between the cables O e. None of above
The 50 ohm transmission line isterminated with an unknown load. The magnitude of the reflection coefficient is R=0.5.Thedistancebetween the voltage maximum and the load is0.15 lambda. What is the imaginary partof the load impedance?

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning