2. The pressure of a hydraulic working cylinder is intensified by using a pressure intensifier. The intensifier have area A₁ against the pump pressure pp and area A2 against the load pressure PL. a) Calculate the pressure ratio A₁/A2 needed to lift the mass m=20000kg, when the pump pressure pp=280bar and work force resisting the piston motion Fw=100kN. The piston diameter D=80mm. pp is approximated to be constant. Losses, including the directional valve loss, are neglected. JA₂ PL m b) What is the lifting speed of the mass, if the pump flow Qp is 120 l/min.

2. The pressure of a hydraulic working cylinder is intensified by using a pressure intensifier. The intensifier have area A₁ against the pump pressure pp and area A2 against the load pressure PL. a) Calculate the pressure ratio A₁/A2 needed to lift the mass m=20000kg, when the pump pressure pp=280bar and work force resisting the piston motion Fw=100kN. The piston diameter D=80mm. pp is approximated to be constant. Losses, including the directional valve loss, are neglected. JA₂ PL m b) What is the lifting speed of the mass, if the pump flow Qp is 120 l/min.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

m 이 D Pi D h
There are two double-acting pneumatic actuators, the extension of each one is executed in 5 seconds at 80 psi and recoil in 4 seconds at 30 psi, the travel of both is 12 inches, the diameter of the piston is dp = 4 "and of the rod dv = 1"a) Determine the compression ratios. The local atmospheric pressure is 79kpa = (11.5 psi)b) Determine the air consumption in cubic feet per minute of free air PCMc) Determine the average air consumption for each.d) Propose the regulation values of the pressure switch, system pressure and safety valve
The piston shown in figure is held in equilibrium by thepressure of the gas flowing through the pipe. The pressurespI = 350 kPa, pII = 130 kPa, and pressure of the gas pIII =210 kPa. Find the mass of the piston. Ans: 80.1 kg Hints: Consider a free body diagram of the piston andidentify the different forces the piston is subjected to get theweight of the piston. The weight of the piston isnumerically equal to its mass since g is not given meaningat standard gravity
. The hydraulic system of a backhoe is used to lift a load asshown in Figure 11.45. (a) Calculate the force F the slavecylinder must exert to support the 400-kg load and the 150-kgbrace and shovel. (b) What is the pressure in the hydraulicfluid if the slave cylinder is 2.50 cm in diameter? (c) Whatforce would you have to exert on a lever with a mechanicaladvantage of 5.00 acting on a master cylinder 0.800 cm indiameter to create this pressure?
80 min 200 mm 11. The figure shows a high-pressure hand pump used for boosting oil pressure in a hydraulic line. When the handle is in equilibrium at theta=15 deg under the action of a force P-120 N, determine the oil pressure p which acts on the 46 mm diameter piston. (Pressure on the top of the piston is atmospheric). 200 mm piston. Ans: P=0.27 MPa mm
Problem No.4 g exerts no force on the piston when it is at the bottom of the yinder and for the state shown the pressure is 400kPa with volume rise 2 em. ma the newv pressure and spring constant? 1000L-Im |Page2
1.The engine has a given capacity of 60kw, calculate the power requirement in a hydraulic system tool , to know that the engine is capable to support the hydraulic system if a pump delivers 110 liters per minute and the pressure is 227bar.2.If the area of A1 = 0.05 m˄2 and the area of A2 = 1.5 m˄2 , external input force F1 = 50 N, then the external output force F2 ?
Ex. 5. A weight lies on a piston with a radius r₂ = 1.0m. Determine the for- ce F₁ applied to the piston with radius r₁ = 20 cm if the hydraulic jack is in a balance. The jack is filled by an oil with po = 850 kg/m³. A mass of we- ight is m 1000 kg. Neglect the mass of the pistons. (Ans. F₁ = 392.4 N) = F₁ 0.3 m m oil
As a junior field engineer, you have been asked to assist a contractor in resolving the following problem. A 4.9 kW motor and gear drive rated at 175 rpm has been shipped with the four impeller blades listed below. The baffled rapid mix tank to which one of the impellers will be installed is 3.0 m² in volume (1.56 m diameter and 1.56 m depth). Assume water temperature of 10C, G= 1000s, water density = 1000 kg/m³, and motor power to water power transfer efficiency of 80%. Impeller options: A. Axial flow, 3 blades, diameter = 0.48 m, N₁-1.0 B. Axial flow, 3 blades, diameter = 0.61 m, Np=1.0 C. Radial flow, 6 blades, diameter = 0.48 m, Np=6.3 D. Radial flow, 6 blades, diameter = 0.61 m, Np 6.3 Answer the following: 3. What is the rotational speed (n) in rps? b. What is the power required in kW for impeller option A? What is the power required in kW for impeller option C? C. d. What is the power transferred to the water from the selected motor in kW? e. Which impeller should be used?…
Fundamental Problem
Please write in clear handwriting za oparation 3. Problem: Detemine the gauge pressure PM at the upper part of one of the two interconnected vessels when a force of P=200 N acts on the piston in the other vessel, di=150 mm, d;=450 mm, d;=200 mm, h=700 mm.
•:) A SPHE RICAL BALLoON IS FILLED WITH HELIUM to A MAXIMUM DIAMETER OF 3¢4 AT A 6AGE PRESSURE OF 8.18 in Ha and 28 TEMPERATURE - FIND THE MASS OF THE HELIVM loNTA INED INSIDE THE BALLOON.