Q1 The screw of the shaft straightener exerts a load of 3000Kg. The screw-type is square threaded of outside diameter (7.5cm) and (6mm) pitch. Take the height of the nut (150mm). Determine 1) Force required at the rim of 30cm diameter hand wheel, assuming a coefficient of friction is 0.12. 2) The maximum compressive stress in the screw, bearing pressure on the thread, and shearing stress in the thread. 3) Efficiency of the straightener. Nut- 150 Hand wheel Screw 100- 150- 400 All dimensions in mm

Q1 The screw of the shaft straightener exerts a load of 3000Kg. The screw-type is square threaded of outside diameter (7.5cm) and (6mm) pitch. Take the height of the nut (150mm). Determine 1) Force required at the rim of 30cm diameter hand wheel, assuming a coefficient of friction is 0.12. 2) The maximum compressive stress in the screw, bearing pressure on the thread, and shearing stress in the thread. 3) Efficiency of the straightener. Nut- 150 Hand wheel Screw 100- 150- 400 All dimensions in mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 m apart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coeffi- cient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be trans- mitted. [Ans. 2.39 kW]
A cylinder is moving a 6000 Ib load up a 20° slope as shown in the figure below. The friction coefficient between the sloping surface and the load is 0.4. The internal cylinder friction is negligible. The piston area is 3 in² and the rod area is 2in?. Provide and answer for both A and B below. A. What cap end pressure (in psi) is required to accelerate the load from O ft/min to 25 ft/min in 0.5 inches? B. What cap end pressure is required (in psi) to move the load up the slope at a constant velocity of 25 ft/min? W Angle
4.As shown in the figure, a square threaded screw is used in a vise to exert a pressure of 2 tons. If the screw is double-threaded and has a pitch of 0.25 m and a mean radius of 1.5 inch, determine the torque that must be applied at B to create this pressure. Assume the coefficient of friction to be 0.15. P
Steel frame with thickness of 10mm, width 80mm and inner diameter of 1500.0mm being heated and shrinkable on steel wheel diameter 1500.5mm. If the coefficient of static friction is 0.30, what is the torque required to roll the tire with respect to the wheel? Neglecting the deformation of the wheel. Use E = 200 GPa.
Q3/ Decide if the copper wire made of ( 4 mm) in diameter is fail or not when it used for pulling a body of 5.6 KN weight on horizontal plain having (0.35) coefficient of friction, suppose that the allowable tensile stress for the copper material is 200 N/mm^2? Answer d=3.53mm
Two equal gear wheel of 360 mm p.c.d and 6 module are in mesh if the pressure angle 20 determine the maximum addendum necessary if there are always to be at least two pairs of teeth in contact . if the gear wheels rorates at 110 r.p.m and 6 kw is being transmetted find the normal force between the teeth assuming that the total force is dividing equally between the two pairs of teeth Neglect the frection. (Ans 6.8mm , 1.54KN .)
An ACME-thread power screw is considered. The coefficient of friction of the thread is mu. The external load on the screw is F. d = 1.75; % (in) major diameter | = 0.25; % (in) screw lead mu = 0.2; % coefficient of friction for thread F = 2000; % (lb) external load on the screw Find: 2.4 the moment required for lowering the load (Ib in)
A square thread jackscrew has a 2 threads per inch. It is to lift 15tons. The friction radius of the collar is 1 in. The coefficient offriction between the threads of the screw and base is 0.15, thatbetween the screw and the collar is 0.13. Determine:a. The diameter of the root of the screw if theallowable stress in compression is 6 000 psi.b. The torque required to turn the screw.c. The pull required at the end of a 5 ft bar raises theload.d. The twisting moment exerted at the root of thethreads.e. The power output of the screw if it is turning at 60rpm.f. The power input of the screw.g. The efficiency of the screw and collar
An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 mapart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted
Q2) design a nut. and screw jack (normal series) manufactured from a high grad materials and workmanship from to lift a load of 80 kN through a height of 400mm. The nominal diameter of the screws 46. The elastic strength of screw materiai in tension and compression is 200 MPa and in shear 120 MPa. The elastic limits of the nut are 100 MPa in tension, 90 MPa in compression and 80 MPa in shear. The bearing pressure between the nut and the screw is not to exceed 18 N/mm2. Design and draw the screw jack. The design should include the design of screw, nut, handle and cup. Assume the S.F is equal to 2.
Hoop stress is limited to (2.4)MPa and density of flywheel material is (7504) Kg/m3
4.) A flat belt makes contact with an 16 in. diameter pulley through half its circumference. If the coefficient of friction is 0.45 , and a torque of300ft−bsis to be transmitted, calculate the belt tensions. (please type answer not write by hend)