1. Compute the block shear strength of the tension member shown in the figure. The holes are for 22- mm-diameter bolts, and A36 steel is used. a. Use LRFD. b. Use ASD. L3½ x 3½ x %, A36 50mm O o o 75mm 75 mm 22-mm dia bolts 38 mm

1. Compute the block shear strength of the tension member shown in the figure. The holes are for 22- mm-diameter bolts, and A36 steel is used. a. Use LRFD. b. Use ASD. L3½ x 3½ x %, A36 50mm O o o 75mm 75 mm 22-mm dia bolts 38 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4. An A992 WF steel section is used for the tension member shown in the figure. The bolts are 20mm…

A: A992 WF steel section, bolts are 20mm in diameter The WF section is to be connected to a 12mm-thick…

Q: snip

A: Calculate the gross area due to yielding. Ag=bt =5×12 =2.5 in2 Calculate the nominal…

Q: The bolted type connection will be used to assemble the given steel members. If PArmax = 8.36 t;…

Q: The plate shown is 8 in wide and 1/2 in thick. The bolts are 7/8 in. The smallest net area (An) of…

A: Given:- width of plate =8 inthickness of plate =1/2 inBolts diameter size = 7/8 inA36 plateTo…

Q: The angle shown below is A992 steel joined to a 3/4 in thick gusset plate (not shown) with 3 bolts.…

A: Consider the given data The bolts are group A bolts with thread not excluded from the shear plane,…

Q: The vertical steel bar is connected with two A307 bolts (diameter = 7/8 inch) in standard round…

A: The values given in the question are as follows: Diameter of bolt(d)=7/8 in or 0.875 in bolt grade…

Q: A 1 ⁄2 × 5-inch plate of A588 steel is used as a tension member. It is connected to a gusset plate…

A: Given: 1⁄2 × 5-inch plate of A588 steel. ⇒Width, b=12in⇒Thickness, t=5 in Diameter of bolts = 5⁄8…

Q: The T-shape shown in the figure is used as a tension member. Given that the gross area Ag = 2556…

A: T- shape member properties:Gross area, Ag = 2556 m2Thickness of web, tw = 10 mmGross depth, D = 220…

Q: Select an S shape for the tension member shown in Figure. The member shown will be connected between…

Q: Check the bolted section of the given gusset plate connection assuming that the connection is done…

Q: lines of M20 bolts shown in the figure, determine the pitch (s) in mm that will give it a net area…

Q: A double-angle shape is shown in Figure 3.5. The steel is A36, and the holes are for…

A: Double angle section is shown in the figure above. Grade A36 steel is used. Diameter of bolts= 1/2…

Q: 3. Determine Rn based on bolt limit states. Slip critical connection is used for design and Grade…

A: sub critical connection Grade- 10.9 M22 Bolts- Class A surface Minimum edge distance and spacing -…

Q: The bolt group shown in Figure P consists of 3⁄4inchdiameter, Group A bearingtype bolts in single…

A: Solution Given Data Diameter= 3/4 inch

Q: The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear…

A: Given: Diameter of bolt= 1 inch ( Group A ) Diameter of bolt hole= d0 =116+1=1.06 inch Plate…

Q: 2.) Compute the tensile capacity for the ½ inch thick plate shown. The bolts are inch diameter high…

Q: An angle section ISA 120 x 100 x 10 is shown in the figure. The bolts used are of diameter 20 mm.…

A: Given data, For ISA 120x100x10 Diameter=20 mm Steel grade is Fe410

Q: The splice plates shown in Figure 2 are ½-inch-thick. How many 7/8-inch-diameter, Group B bolts are…

A: Nominal bolt area is given by

Q: Find the ava shown in the liameter bolts Use LRFI Use ASD 1 2) 3½" I

Q: A single-angle tension member, an L4×4×3/8, liameter bolts as shown in the attached figure is…

A: L4x4x3/8 d= 7/8 in do= 1 in

Q: 4. An A992 WF steel section is used for the tension member shown in the figure. The bolts are 20mm…

A: Section W14x68bolt diameter, db = 20 mmA992 grade of steel:fy = 345 MPafu = 450 MPaTo find:a. The…

Q: The tension member shown is an L150 × 87.5 × 8. The bolts are 19 mm in diameter. If A36 steel is…

Q: olt (threads are not excluded from shear planes) that could resist the loads without failing. Assume…

Q: Problem 6: Assume that the pieces making up the connection are adequate, and very stiff such that…

A: Service load, T=620 kNFrom the given service load, 25% is dead load and 75% is live loadGiven bolt…

Q: The tension member shown in figure below is a PL ½ x 8 of A36 steel. The member is connected to a…

Q: The block shear strength of the tension member as shown in figure is (round off to two decimal…

A: For given tension member,grade of plate Fe410Angle specification: -ISA 80 x 50x 8 mmBolt…

Q: A 620×230 UB 125 tension member of S355 steel is connected through both flanges by 30 mm bolts (in…

A: Properties of 620x230 UB 125 w = Weight of beam = 125 kgD = Total depth of beam = 620 mmbf = Width…

Q: Question 1: Select an S shape for the tension member shown in Figure (1). The member shown will be…

A: Since the total design load (300 kips) is less than the nominal capacity (466.18 kips), the selected…

Q: A Channel Cóx13 is used as a tension member. The holes are for 5/8 inch in diameter of bolts. Using…

Q: Find ØR, considering bolt limit states only. (S275 Steel, fy = 2804 kgf/cm², fu = 4385 kgf/cm²,…

A: fy = 2804kgf/cm2 = 2804 * 9.81/100 N/mm2 = 275N/mm2 fu = 4385kgf/cm2 = 4385 * 9.81/100 N/mm2 =…

Q: Q1. Design the bolted connection. When a bracket is bolted to the flange of a column using a bracket…

A: Consider the free body diagram of given bracket connection with column flange as shown below.Bracket…

Q: a. Determine the ultimate tensile strength of the tension member (channel) based on its gross area.…

A: For channel fu = 450MPa fy = 345MPa

Q: Use ASD to determine the width of the 5/8 inch thick A36 plate subjected to tension as shown below.…

A: ASD5/8 inch thick A36 platedead load, PD=85 kiplive load ,PL=80 kipTwo rows of 5/8 inch standard…

Q: In the connection shown in the figure, the bolts are 3/4 inch in diameter, and A50 steel is used for…

A: The given data is shown below: Diameter of bolt=34-inchA50 steel

Q: miscellaneous channel MC 300 x 67 is bolted as shown on the figure 2.20 by a 0 mm diam. bolts. A 36…

A: Area of section, Depth, Thickness of web, Flange thickness, Width of flange, To find: (a)…

Q: er shown in the accompanying illustration consists of two C12 x 25s (A36 steel) connected to a 25 mm…

Q: The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with…

A: The given connection with dimensions as follows :

Q: (a) Check if the given connection follows the code provisions on spacing and edge distance limits.…

A: Answer (1) Check for Maximum and minimum spacing Minimum spacing As per AISC Manual 14 edition…

Q: Determine the design strength of an UNP300 with four lines if 20 mm diameter bolts in standard…

A: Given- diameter of bolts=20mmFu=370MpaFy=240MpaFor UNP 300B=100mtf=16mmAN=0.949m2/m

Q: The splice plates shown in Figure 2 are 1/2-inch-thick. How many %-inch-diameter, Group B bolts are…

A: Nominal bolt area is 'Ab'

Q: The tension member shown is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter.…

A: Member =58×10 Steel A36 → Fy=36 ksi → Fu=58 ksi Bolts are 78 in. diameter.

Q: Question 17 2L5x3x7mm tension momber is connocted to a gussot plate by 16-mm-diameter bolts as shown…

A: Solution: Given: Section: 2 L5x3x1/4 LLB d = 5 in = 127 mm bw = 3 in = 76.2 t = 1/4 in = 6.35 mm…

Question

1. Compute the block shear strength of the tension member shown in the figure. The holes are for 22-
mm-diameter bolts, and A36 steel is used.
a. Use LRFD.
b. Use ASD.
L3½ x 3½ x %, A36
50mm
O o o
75mm 75 mm
22-mm dia.bolts
38 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Expert Sir , Please solve my question Thanks in advance..
For the bolted tension member is shown in the figure. Determine the effective area, Ae. Given, x = 1.68 inch, Ag = 5.75 inch?. (4)- S/8" A325N bolts L6 x 6 x 1/2 -Tu 3" 3" 3"
See image below. Five M16 8.8/s bolts are used in the connection between a beam and a column. Both sides of the cleat plate are welded to column using fillet weld (Manual metal arc AS4855 B- E43XX) with size of 6 mm. The design force transferred from beam to column is 250 kN. The cleat plate has thickness of 12 mm, fy = 300 MPa, and fu- 360 MPa. Determine the unit stress sustained by the weld (in MPa, keep 1 decimal place). 8.8/5 -360UB56.7 300 Plus 360 So 7°
Please answer all the questions with a complete solution. thank you.
For the cross section shown, calculate the tensile capacity of the steel plate. Assume that the bolt hole is 1/16 inch larger than bolt diameter. Plate 1/2" x 11" .T 7/8" dia. bolt, typ. ASTM A325N
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
PLEASE ANSWER ALL OF THIS QUESTION ASAP!!!
Problem 1: A butt joint shown in Figure ST – 127 using A325 bolts with a diameter of 16 mm with threads excluded in a shear plane. The plate used is A36 steel with Fy = 400 MPa. Use LRFD. Hole diameter is 3 mm larger than the bolt diameter. 1. Compute the design strength Pu of the connection based on bearing of the plate. Hint: The inner plate will govern. No need of checking the outer plate. 2. Compute the design strength Pu of the connection based on bolt shear. Hint: the bolt is in double shear. As is times 2 for every bolt. |32 84 84 12.5 mm T/2 T/2 22 mm 12.5 mm T/2- T/2 + T 180 mm Figure ST - 127
Load and resistance Factor design-tension members Q- Look into the block shear failure mode on the angle L4X4X linked to the 1-inch gusset plate with three 1-inch diameter bolts. Steel A36 is the substance.
The block shear strength of the tension member as shown in figure is (round off to two decimal places). Assume grade of plate Fe410. 45 mm 35 mm 50 mm 100 mm ISA 80 x 50 x 8 mm (M20 bolt of grade 4.6 is used) KN
column section =ISEB500 bracket plate thickness=11mm p=450KN E=270mm p=5mm bolt size =M20