An angle section ISA 120 x 100 x 10 is shown in the figure. The bolts used are of diameter 20 mm. Find the block shear strength of the section if the minimum end distance and distance between the bolts provided is shown in the figure. [Use Fe410 grade of steel] 33 mm 50 mm 50 mm O----- O--..... 50 mm 70 mm

An angle section ISA 120 x 100 x 10 is shown in the figure. The bolts used are of diameter 20 mm. Find the block shear strength of the section if the minimum end distance and distance between the bolts provided is shown in the figure. [Use Fe410 grade of steel] 33 mm 50 mm 50 mm O----- O--..... 50 mm 70 mm

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter28: Structural Components Of Framed Construction

Section: Chapter Questions

Problem 28.34Q

See similar textbooks

Similar questions

Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem The butt connection shows 8-22 mm dia. A325 bolts spaced as follows: S1 = 40 mm S3 = 50 mm t1 = 16 mm S2 = 80 mm S4 = 100 mm t2 = 12 mm Steel strength and stresses are: Fy = 248 MPa Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Bolt Hole diameter = 25 mm Questions: Calculate the allowable tensile load T, under the following conditions. a) Based on the gross area of the plate b) Based on the net area of the plate c) Based on block shear strength
Design the size and length of Fillet weld for the lap joint shown below, Use SMAW E70XX process, plates are A-36 steel? 90k LL 40k DL R-X7 5" Gusset P 8 90k LL 40k DL
4. As shown below, the splicing joint of a beam was made with bearing type high-strength bolts. The loads transferred through the joint is V=3000KN, M=90KN.m. The bolts are of grade 10.9, nominal diameter 22mm, effective area Ae=2.45cm2;f=310N/ mm?; f-500N/mm²; End plates made of Q235B steel, thickness 22mm, fe-470N/mm?. Check the strength of this bolt connection. -24mm 35 130 35 80 V 1 og1 081 1 081
A bearing type connection is shown in Figure 3.19. The diameter of A 325 bolts is 22 mm and the A572 Grade 50 plate material has a width of 150 mm and thickness of 16 mm. Assume diameter hole to be 24 mm. Bolt threads are excluded from the shear plane. Allowable stress of A 325 bolts: Fv = 207 MPa Fp = 1.5 Fu (to prevent excessive hole deformation) Allowable stresses of A572 Grade 50 plate material: Fy = 345 MPa Fu = 450 MPa a. Compute the tensile capacity due to the failure of the plates. b. Compute the tensile capacity due to the failure of the bolts.
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
The diagonal at the left to the connection is a double angle 90 mm x 90 mm x 8 mm, with area of 2700 mm?, bolted to the 8 mm thick gusset plate. Bolt diameter = 16 mm Bolt hole diameter = 18 mm Bolt bearing capacity, Fp = 480 MPa Bolt shear strength, Fv = 68 MPa Steel plate strength and stresses are as follows: Yield strength, Fy 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 0.60 Fy Allowable tensile stress on the net area = %3D 0.50 Fu Allowable shear stress on the net area = 0.30 Fu Bolt bearing capacity, Fp = 1.2 Fy Calculate the allowable tensile load, P(kN) under the following conditions: %3D
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
The butt connection shows 8-22 mm diameter bolts spaced as shown below. P- 50 100 50 50 100 50 16 mm +HHHH 40 80 40 12 mm Steel strength and stresses are: Yield strength, Fy = 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Based on the gross area of the plate. Based on the net area of the plate. Based on block shear strength. Bolt hole diameter = 25 mm Calculate the allowable tensile load, P, under the following conditions:
Q21 In the connection shown in Figure below, the bolts are %in diameter, and A36 steel is used for all components. Compute the design Strength of the connection. 12" 12" 22"
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 100x100x10mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu=483.33 MPa. Fv = 0.30 Fu Questions: a) Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. b) Determine the length of side fillet weld required at the heel. c) Determine the length of side fillet weld required at the toe.
Prepare an excel file and to find a) area of the bolt, b) Average Shear Stress Bolt c) Bearing Area Stress and d) allowable stress. Applied force range – 500 to 1000 N (in step of 100 N) Bolt diameter range – 10 to 25 mm (in step of 5 mm) Plate thickness – 10 mm Consider ultimate tensile strength as 460 N/mm2. And consider factor of safety as 1.5.
What is the safe load "P" that can be transmitted by the fillet-weld joint shown in figure below if allowable shear stress in the fillet weld is 108 MPa and F.O.S. for load is 1.5? P4 www 60mm 777 50mm 8mm P