The splice plates shown in Figure 2 are ½-inch-thick. How many 7/8-inch-diameter, Group B bolts are required? The given load consists of 30% dead load and 70% live load. A36 steel is used. Threads are not excluded from the shear plane. 90 k Figure 2 ¾ in. 90 k

The splice plates shown in Figure 2 are ½-inch-thick. How many 7/8-inch-diameter, Group B bolts are required? The given load consists of 30% dead load and 70% live load. A36 steel is used. Threads are not excluded from the shear plane. 90 k Figure 2 ¾ in. 90 k

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter7: Simple Connections

Section: Chapter Questions

Problem 7.4.3P

See similar textbooks

Related questions

Q: oblem What is the perimeter in feet of exposed wall for the entire house provided? NOTE 1: The wall…

A: To find:The perimeter in feet of exposed wall for the entire house.The perimeter of the wall:The…

Q: A 12 kN 9 kN/m |C -1.5 m 1.5 m-1.5 m 1.5 m B

Q: . Polar moment of inertia (Ip), in cm4, of a rectangular section having width, and depth, d = 6 cm…

Q: A simply supported beam with spans of LAB = 8 ft and LBc = 24 ft supports loads of w = 4.5 kips/ft…

A: Maximum shear stress and Maximum bending stress in the beam.

Q: 40 cm I 30 cm 50 cm 3. Using the shape shown in the figure, for a design moment of 7500 N.m, what…

Q: S W P 5m B 3 m fixed I. Problem Solving: Solve the following situations as completely as possible,…

Q: Problem 5 Classify each of the following trusses as statically determinate, statically…

A: To find whether the given truss is statically determinate or indeterminate and its degree.

Q: Q: Water is flowing through a soil as shown in the figure. Pressure head at C (i.e. uc) is 8m.…

Q: a field vane shear test, a 150-mm long and 75-mm wide vane is pressed into a soft clay at the…

A: given T=50 NmH=150 mmD=75 mmassuming one end shear

Q: Hi can you please help with the Truss exercise

Q: Design a concrete lined channel of trapezoidal section to carry a discharge of 250 cumecs at a…

Q: V two-wa Q3 The time for 65% consolidation of a 19-mm clay specimen (drained at top and bottom) in…

A: Given data-Case 1%Consolidation (%U) = 65%Height of clay layer = 19 mmDouble drainage condition…

Q: с B 4 m FIGURE Q2(a) A 2m

Q: Figure shows a clean sand having a permeability of 0.075 cm/s and a void ratio of 0.62 placed in a…

Q: The ratio of the deflection of the free end of 1 a cantilever due to an isolated load at 3rd and 2|3…

Q: Determine the shape of the simply supported fully stressed beam that supports a linearly varying…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub- parts for…

Q: Determine the stress in a fiber (in psi) located 1inch from the top of the beam and 4 feet from the…

Q: Handwritten answers only pls. For this one compute support reactions and drive a shear and moment…

A: Determine the support reaction and draw shear force and bending moment diagram of the beam. Note: As…

Q: Refer to the figure below: Determine the deflection (delta) in mm at point B. Use E = 200 GPa and I…

A: E = 200 GPaI = 2100 mm4 Determine the vertical reaction at the hinge support and deflection at…

Q: (i) A multistory building with a basement is to be constructed. Top 4 m consists of loose silt,…

Q: A granular soil has a saturated unit weight of 20 kN/m² and an effective angle of shearing…

A: A granular soil having,

Q: Ily. The buckling stress (in N/mm2) of the vertical bar is

Q: 3. The given triangular AB gate is hinged at A. Determine the weight of the gate that is required to…

Q: prin... x 2/3 EJ D KDH DO Q.1) A section of cantilever sheet-pile wall is given in the figure below.…

Q: (c) Determine the length of X and Y for the rectangular plate as shown in FIGURE Q1(b) if the area…

A: Area of rectangular plate, A = 2 m2.Perimeter of rectangular plate, P=2X+2Y = 500 cmIt is asked to…

Q: Owrate of 30000 m³/day and influent BOD of 250 mg/L. The first and composed of three and two…

A: two stage trickling filterin first stage there are 3 filters and in second stage there is two…

Q: 1. Problem Solving: Solve the following situations as completely as possible, use any method that…

A: Note: As per Bartleby guidelines only first three subparts will be discussed in this solution. We…

Q: Design a square pile group to carry 400 kN in clay with an unconfined compression strength of 60kN…

A: Given:To Determine:Design of square pile group from above data

Q: A soil profile consists of a sand layer 2m thick, whose top is the ground surface, and a clay layer…

A: We know that the consolidation settlement at any time is given by U = *100U = Degree of…

Q: If block A is moving downward at 6 ft/s while block C is moving down at 18 ft/s, determine the speed…

Q: Problem 3 Determine the support reactions of the beam loaded as shown below then draw the shear and…

Q: A rectangular channel has a width "B" and manning's coefficient "n. For a discharge of Q and energy…

A: Write down the formula how to calculate yo Sketching the profile type of the given GVF

Q: 6) The simply supported beam with given cross-section supports the loads as shown. Determine the…

A: Flexural Stressfb < 120Mpa in tensionfb = 140 Mpa in CompressionShearing Stress

Q: Q: Water is flowing through an inclined aquifer (a=15°) as shown in the following figure. The depth…

Q: Subject: Fundamentals of Deformable Bodies Question 1.) Find the vertical support reaction at A and…

Q: By assuming a linear speed-density relationship, the mean free speed on a highway facility lane…

A: The speed-density Relationship is;

Q: Q- A transition curve is to be provided for a circular railway curve 236 m radius. The gauge is 12m…

A: A transition curve to be provided for a circular railway curve.Radius of circular railway curve…

Q: 2. For each structure shown, compute the reactions and draw shear and bending moment diagrams.…

A: Given:Required :Support reactions and shear force diagram and bending moment diagram

Q: The reduced bearing of 20 m long line is S30° E the latitude of the line is A 17.32 m north B 10 m…

A: Given;Length = 20 mAngle () = S30E

Q: The reduced bearing of 20 m long line is S30° E the latitude of the line is A 17.32 m north B с…

A: Length of the line L=20 mBearing S 30o ELatitude of the line = ?

Q: Can you adjust the answers I think the external loads don't take one equation out of consideration…

A: The solutions of a,b,c provided by expert is wrong.I am providing the good solution for you.See my…

Q: Specific Gravity and Absorption of Coarse Aggregates What are the possible discussion of…

A: There are two types of aggregates, they are fine aggregate and coarse aggregate. Coarse aggregate…

Q: An area of a field is 250 square centimeters from a shrunk map having shrunk factor of a 0.9.…

Q: Find the maximum moment of the given load train at point n on the beam given in the figure?

A: We have to find out the maximum bending moment at section n.

Q: Q.1) A section of cantilever sheet-pile wall is given in the figure below. Considering both passive…

Q: After how many days will you supply water to soil in order to ensure sufficient irrigation of the…

Q: What are the key principles of neutrality and impartiality in mediation and arbitration?

A: Neutrality and impartiality are two fundamental principles in the fields of mediation and…

Q: A rectangular channel carries a uniform flow with a Froude number of 2.83. The ratio of critical…

A: Froude number= 2.83Find ratio of critical depth to normal depth of this flow.?

Q: Problem 3) For the beam shown in Figure 3C, using the moment area theorems determine: a) The slope…

Q: A soil is composed of solid spherical grains of identical specific gravity and diameter between…

A: Solid spherical grains-Diameter of larger grain Diameter of smaller grain Terminal velocity of…

Question

The splice plates shown in Figure 2 are 1/2-inch-thick.
How many 7/8-inch-diameter, Group B bolts are required? The given load consists of 30% dead
load and 70% live load. A36 steel is used. Threads are not excluded from the shear plane.
90 k
Figure 2
¾ in.
90 k

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Calculate the Nominal bolt area

VIEW

Step 2: Calculate the nominal strength of bolt

VIEW

Step 3: Calculate the Bolt strength and Factored load

VIEW

Step 4: Calculate the number of bolts

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 12 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58 ksi. The connection is with 9/8-inch-diameter bolts. -→| 20 |einetein | 21 | 6 spaces @2" t = 1/2 in. Compute the nominal strength based on the net section. (Express your answer to three significant figures.) P₁ = kips
For the splice connection shown in the figure, a. Check all spacing and edge-distance requirements. (For 1-in diameter bolts minimum edge distance is 1.25 in. AISC Table J3.4) b. Compute the design strength based on shear and bearing. (Use LRFD) The plates are PL 1/2" x 7" steel ASTM A36 (Fy = 36 ksi, Fu = 58 ksi) and the bolts are 1-in diameter A325X (Fnv = 60 ksi) in standard holes.
Determine the maximum factored LRFD tensile force capacity in tension only (no block shear). The angle is ASTM A36 steel. X = 0.7 Y = 3.8 Z=1/2 Round your answer to 2 decimal places. Your Answer: Incorrect The answer is 77.15 ± 1%. 1/2" X" bolts 1½" Gusset plate -L3 X 3 X Z Tu I
Compute the tensile capacity for the ½ inch thick plate shown. The bolts are ¾ inch diameter high strength bolts. The steel is A36. 24" -P, 1 3"
4. Determine the design strength of the connection shown in the Figure below. Thebolts are 25 mm diameter A490 bolts with the threads not in the plane of shear.A36 steel is used (Fy = 250 MPa, Fu = 400 MPa).a. Compute the shear strength for all bolts.b. Compute the bearing strength for the tension member on all bolts.c. Compute the bearing strength for the gusset plate on all bolts.d. Compute the tensile strength of the tension member.e. Compute the design strength of the connection.
3. Determine Rn based on bolt limit states. Slip critical connection is used for design and Grade 10.9 M22 Bolts with Class A surface. Check minimum edge distance and spacing with TSSDC 2016. All members are $355. There is no filler between plates and Du=1.0. Fy= 355 MPa; Fu=510 MPa; E=200000 MPa. All units are in mm. $R.=? 100 100 O 60 Geset Plate 75 Plate Gusset Plate $R.=? *20*201 Plate
The butt connection shows 8-22 mm diameter bolts spaced as shown below. P- 50 100 50 50 100 50 16 mm +HHHH 40 80 40 12 mm Steel strength and stresses are: Yield strength, Fy = 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Based on the gross area of the plate. Based on the net area of the plate. Based on block shear strength. Bolt hole diameter = 25 mm Calculate the allowable tensile load, P, under the following conditions:
A992 steel is used for the tension member shown. The bolts are ¾ inch in diameter. The connection is to a ⅜ inch thick gusset plate. A. Determine the nominal strength based on the gross area. B. Determine the nominal strength based on the effective net area.
Find the available strength of the S-shape shown in the figure. The holes are for 3/4-inch- diameter bolts. Use A36 steel. Use LRFD Use ASD (1 (2) 3½" I S15 × 50 $23/4" CIVIL ENGINEERING- STEEL DESIGN 1½" 12" e b С d Answer VUZMGL
EXAMPLE #2: Compute the block shear design strength of the tension member shown in the figure. The holes are for 7/8- inch bolts and A36 steel is used (Fy 36 ksi, Fu = 58ksi) Assime Ubs* 10 L3½ x 3% x %, A36 3" 3" 76-in, bolts
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for block shear in kip? Express your answer in two decimal places. 1/2" thick Gusset Plate 3/8" thick 2" 3" 2" 2" 3" 3" 2"
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.