A Channel Cóx13 is used as a tension member. The holes are for 5/8 inch in diameter of bolts. Using A36 steel with Fy=36 ksi and Fu=58 ksi. The gross area of C6x13 is 3.81 in2 and Assume U =0.85 Using LRFD what is the design strength based on Tensile Rupture/Fracture 4 @ 2" a 1 1/2 Ob 3" Oc 1 1/2 " I d e C6 x 13 Round your answer to 3 decimal places.
Q: what should be the area of the stand pipe for the head to drop from 700cm to 360cm in 7 mins
A: FALLING HEAD PERMEABILITY TEST:
Q: Determine the Deflection at the midspan of AB. Use the Any Geometric Method (once for DIM, once for ...
A:
Q: A 50-yr flood typhoon occurred in Metro Manila, started from 12:00AM of Dec 14 to 12:00PM of Dec16. ...
A: According to Horton, the infiltration rate of soil is maximum at the initial time of precipitation a...
Q: Situation 1 - a. A soil sample has specific gravity of 2.7 and unit weight at zero air voids 15.08k...
A: Given that, specific gravity, G = 2.7 unit weight at zero air voids, γd = 15.08 kN/m3 The void rati...
Q: what is the status of contract which it is impossible to perform in civil engineering?
A: We have to determine the status of the contract or what is to be called if it is impossible to perfo...
Q: What is your realization about smart fabrics?
A: Solution:- Smart textiles applications are able to sense and respond to changes in their environment...
Q: Q. In a tri-axial test for a normally consolidated soil, the normal stress at failure is equal to 45...
A: Given, At failure plane,normal stress, σ =450 kPashear stress, τ=350 kPa
Q: Question 1. Determine the vertical deflection under the load and point D of the beam shown in the fi...
A:
Q: 2.4 The section through a long cofferdam is shown in Figure 2.24, the coefficient of permeability of...
A: “Since you have asked multiple question, we will solve the first question for you. If you want any ...
Q: Compute the Concrete mix proportion for a 1ftx1ftx1ft concrete box fc'=21MPA slump=75-100mm Nominal ...
A: Reference : ACI - 318 All tables are taken from ACI - 318 mix design code Table : Relation between c...
Q: sult of the particle-size analysis of a soil are as follows: Sieve No. % Passing 10 40 100 80
A: iAs Passing through 200 = 58>35%Silt-clay -materialiiLL=30≤40PI=10≤10Belongs to A-4
Q: 2. In order to evaluate the suitability of non-potable water available at the job site for mixing co...
A:
Q: Problem 20 k G y 10k E 15 ft F 10k russ is subjected to the following forces as pwn. Determine: 10 f...
A: To find the support reactions and resultant force-
Q: A concrete beam of rectangular cross-section of 200 mm x 400 mm is pre-stressed with a force 400 kN ...
A:
Q: 4m Oil (0.90) 3.75 mm Mercury (13.57) This vertical pipeline with attached gage and manometer contai...
A: Given data in question Vertical pipe Specific gravity Mercury To find out Pressure at A in bars
Q: Please help me answer the problem with a solution and box the final answer. Thank you for helping me...
A:
Q: A stainless-steel rod 16mm in diameter and 300mm long is put under a tensile load of 250 kN. Assumin...
A: Given data Initial diameter of the rod(Di) = 16 mm Then Area (Ai) = (π/4)*Di2 = 201.062 mm2 Init...
Q: A snow load transfers the forces as shown in Fig. for Q. No. 01 to the upper joints of a Pratt roof ...
A:
Q: Sketch the cross-sectional picture of a W8x67 sitting on top of a W16x26 (the vertical centerlines a...
A:
Q: 1bomm
A:
Q: Illustrate and discuss briefly the five distinct features of a hydrograph.
A:
Q: smart fabrics/textile
A: Smart textiles are intelligent textile structures or fabrics that can sense and react to environment...
Q: A beam, with a simple span of 10m and overhang of 2m at the left support, is subjected to a uniforml...
A: We will draw ILD for each cases
Q: 2400 lb 200 lb/ft 1.5 EI EI 30 10
A: Given data:
Q: ACTIVIJ', 200N Me 0.20 30N sの3e REA'O: a, T, ¿ Tz ム。
A:
Q: In the given loaded beam determine the resultant force, R and its location from the point A as it in...
A:
Q: evapotranspiration rate
A:
Q: 30. The proposed embankment fill requires 8000m³of compacted soil. The void ratio of the compacted f...
A:
Q: Sketch the cross-sectional picture of a W8x67 sitting on top of a W16x26 (the vertical centerlines a...
A:
Q: A sand layer having the cross section area as shown has been determined to exist for 350m length of ...
A: We knowQ=kiAi=hydraulic gradient =ΔHL=140-20110=211Area=thickness×Length =1.5×350so,
Q: A wooden log is to be used as a footbridge to span a gap. The log is required to support a concentra...
A:
Q: 10,000 lb Cylinder Plunger AA2 = 10 IN A=500 in? 15" Oil (0.78)
A:
Q: What personal and technical abilities are the most important for the engineer who is engaging in the...
A: The engineer should have following personal and technical abilities.
Q: Determine the reactions at all supports and the force transmitted through the hinge at C for the giv...
A: To find reaction at support
Q: elevation
A:
Q: Two automobiles A and B shown below are approaching each other in adjacent highway lanes. At t = 0, ...
A: Determine (a) the uniform accelerations of A and B, (b) when the vehicles pass each other, (c) the s...
Q: From the table below, compute the catchment volume from the total data of precipitation, runoff, gro...
A: Solution: To compute the catchment volume from the given water; A simplified equation for the water ...
Q: Assume you are observing traffic in a single lane of a highway at a specific location. You measure t...
A: Appreciate if there is detailed work with explanation for ease of understanding. THANK YOU !
Q: 1. Assume 3K1=K2=1.5K3=2K4 K1=3.5x10-2 (cm/s) Calculate the equivalent coefficient of permeability. ...
A:
Q: Figuré 4: 1.2M 0.6M HINGE 4000 Kg OIL (S=0.6)
A: Cross section area of piston at A, AA =700cm2Cross section area of piston at B, AB =120cm2Specific g...
Q: A contract can be terminated during the construction of a project. There are a variety of reasons fo...
A: To Explain: Three types of termination of contract which impact the cycle of project and consequenc...
Q: The back fill material for a vibroflotation project has the following grain sizes. D10 0.11mm D20 0....
A:
Q: 5. A steel punch can be worked to a compressive stress of 800 MPa. Find the least diameter of hole w...
A: To determine least diameter of the hole that can be punched for the given steel plate. Given, Allo...
Q: A simply supported one way reinforced concrete floor slab has a span of 4 m. It carries a service li...
A:
Q: It is the regular inspection and review of the progress of the project Profiling ...
A: Profiling: Project profiling is the the process of working out the scope and characteristics of a pr...
Q: A beam is loaded as shown in the figure SE001. Determine the maximum shear.
A: To find maximum shear
Q: A Grade 40 (40 ksi) 2 pcs-1" Ø cable is, used as tension rods, is placed 2 ft from the ends of the R...
A:
Q: IA 3' Air 2" Oil B 2 3' C
A: Gauge pressure at A, PA =17psi =17lbin2Gauge pressuee at B =Gauge pressure at C -2.2 psi⇒PB =Pc -2.2...
Q: 3. A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A mak...
A: A member subjected to pull is given and it has been asked to determine normal and shear stress throu...
Q: Problem 1. Find the reactions in the beam loaded as shown in the figure. Check answers. 4 kN/M 40 kN...
A:
Step by step
Solved in 3 steps with 2 images
- A double-angle shape is shown in the figure. The steel is A36, and the holes are for 2-inch-diameter bolts. Assume that A₂ = 0.75An. Ae 1 2 Determine the design tensile strength for LRFD. Determine the allowable strength for ASD. CIVIL ENGINEERING - STEEL DESIGN AL Section 2L5 x 3 x 516 LLBBA double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 215 x 3 x %6 LLBB Determine the design tensile strength for LRFD. Select one: а. 66 b. 156 c. 78 d. 132A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0.a) Determine the design tensile strength of the section based on yielding of the gross area.b) Determine the critical net area of the connection shown.
- 3. A plate with width of 300mm and thickness of 20mm is to be connected to two plates of the same width with half the thickness by 24mm diameter bolts, as shown. The rivet holes have a diameter of 2mm larger than the rivet diameter. The plate is A36 steel with yield strength F,-248MPa and ultimate strength F,-400MPa. a. Determine the design strength of the section. b. Determine the allowable strength of the section 24mm 30mmThe tension member shown is an angle L150 x 90 x 10, of A36 steel, with Fy= 250 MPa and Fu= 400 MPa, and is subjected to a service DL= 150 KN and a service LL= 150 KN The bolts are 20 mm o. Use ASD. 40mm 40mn 40mm 50mm ... Compute the allowable strength based on yielding in KN.0 Compute the nominal strength based on fracture in KN.0 Check the adequacy of the section.0The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
- The given angle bar L125x75x12 with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm diameter bolts as shown in the figure. Using A36 steel with Fy = 248 MPa and Fu = 400 MPa, determine the following: 2. Determine the nominal tensile strength of the 12 mm thick, A36 angle bar shown based on: a. Gross yielding b. Tensile rupture Bolts used for the connection are 20 mm in diameter. O O O O O O O Effective net area of the tension member if the shear lag factor is 0.80. Select the correct response: 1,516.1 1,354.4 1,431.2 1,221.6Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block shearDetermine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
- A PL 38 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy = 36ksi, Fu = 58ksi). a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area PL % x 6 3/8" 6" Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2 Blank 1 Add your answer Blank 2 Add your answerThe tension member is a PL 12 x 6. It is connected to a 38-inch-thick gusset plate with 7/8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16" Use: Consider deformation at the bolt hole 3" PL ... PL ½x 6 12" 24" 24" 12" a. What is the minimum spacing as per AISC code provisions Round your answer to 3 decimal places.A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.