Machine Tool Practices (10th Edition)
10th Edition
ISBN: 9780132912655
Author: Richard R. Kibbe, Roland O. Meyer, Warren T. White, John E. Neely, Jon Stenerson, Kelly Curran
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter B.4, Problem 8ST
What are the coarseness designations for needle files?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
What is compound indexing?
Type of gear ?Type of tolerance ?
What is the geometric term that applies to V-groove?
Chapter B Solutions
Machine Tool Practices (10th Edition)
Ch. B.1 - Why is it important to know how to use the arbor...Ch. B.1 - What kinds of arbor presses are made? What makes...Ch. B.1 - List several uses of the arbor press.Ch. B.1 - A newly machined steel shaft with an interference...Ch. B.1 - The ram of an arbor press is loose in its guide...Ch. B.1 - When a bushing is pushed into a bore that is...Ch. B.1 - Prob. 7STCh. B.1 - What difference is there in the way a press fit is...Ch. B.1 - Prior to installing a bushing with the arbor...Ch. B.1 - Name five ways to avoid tool breakage and other...
Ch. B.2 - Prob. 1STCh. B.2 - Name two types of bench visesCh. B.2 - Prob. 3STCh. B.2 - Prob. 4STCh. B.2 - How can the finished surface of a part be...Ch. B.2 - Name three things that should never be done to a...Ch. B.2 - How should a vise be Lubricated?Ch. B.2 - Prob. 8STCh. B.2 - Prob. 9STCh. B.2 - Prob. 10STCh. B.2 - Prob. 11STCh. B.2 - What advantage does the lever-jawed wrench offer...Ch. B.2 - Prob. 13STCh. B.2 - Some objects should never be struck with a hard...Ch. B.2 - A machine has a capscrew that needs to be...Ch. B.2 - Why should pipe wrenches never be used on bolts,...Ch. B.2 - What are the two important things to remember...Ch. B.3 - What is the kerf?Ch. B.3 - What is the set on a saw blade?Ch. B.3 - What is the pitch of the hacksaw blade?Ch. B.3 - What determines the selection of a saw blade for a...Ch. B.3 - Hand hacksaw blades fall into two basic...Ch. B.3 - What speed should be used in hand hacksawing?Ch. B.3 - Give four causes that make saw blades dull.Ch. B.3 - Give two reasons why hacksaw blades break.Ch. B.3 - A new hacksaw blade should not be used in a cut...Ch. B.3 - What dangers exist when a hacksaw blade breaks...Ch. B.4 - Prob. 1STCh. B.4 - What are the four different cuts found on files?Ch. B.4 - Name four coarseness designations for files.Ch. B.4 - Which of the two kinds of files-single cut or...Ch. B.4 - Why are the faces of most files slightly convex?Ch. B.4 - What difference exists between a mill file and an...Ch. B.4 - In what way does an American pattern file differ...Ch. B.4 - What are the coarseness designations for needle...Ch. B.4 - Why should files be stored so do not touch each...Ch. B.4 - Prob. 10STCh. B.4 - What causes a file to get dull?Ch. B.4 - Why should a handle be used on a file?Ch. B.4 - Prob. 13STCh. B.4 - Prob. 14STCh. B.4 - How does the hardness of a workpiece affect the...Ch. B.4 - Prob. 16STCh. B.4 - Should pressure be applied to a file on the return...Ch. B.4 - Why is a round file rotated while it is being...Ch. B.5 - Prob. 1STCh. B.5 - What is the purpose of a starting taper on a...Ch. B.5 - What is the advantage of a spiral flute reamer...Ch. B.5 - How does the shank diameter of a hand reamer...Ch. B.5 - Prob. 5STCh. B.5 - Prob. 6STCh. B.5 - What is the purpose of cutting fluid in reaming?Ch. B.5 - Prob. 8STCh. B.5 - How much reaming allowance is left for hand...Ch. B.5 - If you were repairing the lathe tailstock taper,...Ch. B.6 - What type of tap is used to produce threads that...Ch. B.6 - Prob. 2STCh. B.6 - Prob. 3STCh. B.6 - When is a spiral fluted tap used?Ch. B.6 - How are thread-forming taps different from...Ch. B.6 - How are taper pipe taps identified?Ch. B.6 - Why are finishing and roughing Acme taps used?Ch. B.6 - Why are rake angles varied on taps for different...Ch. B.6 - Prob. 9STCh. B.6 - Prob. 10STCh. B.7 - What kind of tools are used to drive taps when...Ch. B.7 - What is a hand tapper?Ch. B.7 - What is a tapping attachment?Ch. B.7 - Which three factors affect the strength of a...Ch. B.7 - How deep should the usable threads be in a tapped...Ch. B.7 - When should tap drill holes be reamed?Ch. B.7 - What causes taps to break while tapping?Ch. B.7 - What causes rough and tom threads?Ch. B.7 - What causes oversized threads in a hole?Ch. B.7 - Give three methods of removing broken taps from...Ch. B.8 - What is a die?Ch. B.8 - What tool is used to drive a die?Ch. B.8 - How much adjustment is possible with a round split...Ch. B.8 - What is the purpose of the guide in a two-piece...Ch. B.8 - What are important points to watch when assembling...Ch. B.8 - Where are hexagon rethreading dies used?Ch. B.8 - Why do dies have a chamfer on the cutting end?Ch. B.8 - Why are cutting fluids used?Ch. B.8 - What diameter should a rod be before being...Ch. B.8 - Why should a rod be chamfered before being...Ch. B.9 - What is the primary function of the pedestal...Ch. B.9 - Why should a tool grinder never be used for rough...Ch. B.9 - Prob. 3STCh. B.9 - When sharpening layout tolls and other tools, what...Ch. B.9 - Prob. 5STCh. B.9 - Prob. 6STCh. B.9 - Prob. 7STCh. B.9 - What is the purpose of the wheel blotter?Ch. B.9 - Prob. 9STCh. B.9 - What does the wheel ring test do?
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- What is the pitch of a M10 x 1.25 thread?arrow_forward1) What does the specification "8.8" in the standard designation of a bolt mean? Specify values including units. 2) Name two groups of standards in addition to national, industry-wide standards and where they are valid. 3) Which three options exist for defining dimensional tolerances in a technical drawing?arrow_forwardWhat is the mechanical advantage of a 1/4" diameter screw with 20 threads per inch?arrow_forward
- -How many holes require drilling? -What is the center to center distance of the 6mm tapped holes? -What tap drill is used for holes marked Z? -How many surfaces are machine finished? -What are the dimensions of the face marked F & C? -What are the dimensions have symbols A, E &, B -In what dihedral angle is the drawing made? -What is the max and min dimensions of D -What is the tolerance of measurement D?arrow_forwardConsider a thread callout of Dia 0.375-10 UNF-2B. How far will the thread travel if it is subjected to 3 full rotations? (Assume infinite thread lengths for simplicity)? Units are in Inches please answer quicklyarrow_forwardWhy it is important to loosen one screw before tightening the opposing one by an equal amount?arrow_forward
- Thread Fits and 7. Define fit, allowance, tolerance, and limits. 8. How are external UNC threads classified? 9. Name and describe three classifications of UNC fits. 10. How are thread fits designated for the ISO threads? Classifications 11. Why was the ISO metric system of threads adopted? 12. Describe a thread designated as M 56 X 5.5. 13. Name five thread forms used in North America and state the included angle of each. 14. What are the principal differences between the American and Unified threads?arrow_forward21 The root of a thread is defined as what? Multiple Choice (select the best answer) The surface of the thread along the minor diameter. The surface of the thread along the major diameter. O The distance a screw travels axially with one rotation. O The measurement between the crest and root of a single thread. 22 The thread depth of a thread is defined as what? Multiple Choice (select the best answer) O The measurement between the crest and root of a single thread. O The number of threads which span one inch of an inch series thread. O The surface of the thread along the minor diameter. O None of the Above What operation finishes a hole to a precise size with a Multiple Cholce (select the best answer) 23 O Drilling Tapping Reaming None of the Abovearrow_forwardWrite the NC part program for the part. Holes are threaded and requires two tools; T1 is a 0.5" HSS drill bit and T2 is a 0.5" tapping bit. The rest of the features are cut using a 0.75" HSS milling tool, T3. Feed rate and spindle speed are 10 ipm and 2000 rpm. The material is low- carbon steel. Part thickness is 0.5”. Use dotted lines two show the path of tools movements. Set up proper operation conditions as discussed in the class today.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Precision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Hand Tools; Author: UCI Media;https://www.youtube.com/watch?v=4o0tqF0jDdo;License: Standard Youtube License