Programmable Logic Controllers
5th Edition
ISBN: 9780073373843
Author: Frank D. Petruzella
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 6, Problem 7P
Program Plan Intro
Programmable Logic Controller (PLC):
- PLC is a specialized computer used in industrial segments to control machines and process.
- PLC is program that consists of a set of instructions which resembles the controlling functions needed to perform specific tasks.
- The function of PLC is similar to that of a relay and hence, in an industrial segment a relay is greatly replaced by a suitable PLC.
- When compared to general Personal Computer (PC), a PLC is available in small and tiny sizes.
- The basic architecture of a PLC consists of an input-output interface module and a small Central Processing Unit (CPU) that runs by controlling
programming language.
Given:
The following motor control specifications must be satisfied by the ladder logic program.
- Three start/stop pushbutton stations are used to start and stop the motor.
- One Normally Open (NO) start pushbutton and one Normally Closed (NC) stop pushbutton will be contained by each start/stop station.
- Motor OL contacts are hardwired.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
.............Control loop is a continuous cycle of the PLC reading
Ladder Logic O
Outputs
Inputs O
Homework Problem 1
Create a PLC program, ladder logic and timing diagram for the following light output using timers.
Light Status- (*=On) (0=Off)
0-5 Seconds
5-10 Seconds
10-15 Seconds 15-20 Seconds 20- Seconds
0000
0 ** 0
• 00*
00 od
PLC programming
Draw or write a ladder plc diagr for 3 proximity
sensor. The proximity sensor is position right and
left and 1 in front.
Chapter 6 Solutions
Programmable Logic Controllers
Ch. 6 - Prob. 1RQCh. 6 - Prob. 2RQCh. 6 - Prob. 3RQCh. 6 - Prob. 4RQCh. 6 - Prob. 5RQCh. 6 - Prob. 6RQCh. 6 - Prob. 7RQCh. 6 - Prob. 8RQCh. 6 - What do the abbreviations NO and NC represent when...Ch. 6 - Prob. 10RQ
Ch. 6 - Prob. 11RQCh. 6 - Prob. 12RQCh. 6 - Compare the operation of a photovoltaic solar cell...Ch. 6 - What are the two basic components of a...Ch. 6 - Prob. 15RQCh. 6 - Give an explanation of how a scanner and a decoder...Ch. 6 - Prob. 17RQCh. 6 - Prob. 18RQCh. 6 - Prob. 19RQCh. 6 - Prob. 20RQCh. 6 - Prob. 21RQCh. 6 - Prob. 22RQCh. 6 - Prob. 23RQCh. 6 - Prob. 24RQCh. 6 - Prob. 25RQCh. 6 - Prob. 26RQCh. 6 - Prob. 27RQCh. 6 - Prob. 28RQCh. 6 - Prob. 29RQCh. 6 - Prob. 30RQCh. 6 - Prob. 31RQCh. 6 - Prob. 32RQCh. 6 - Prob. 33RQCh. 6 - Prob. 1PCh. 6 - Prob. 2PCh. 6 - Prob. 3PCh. 6 - Prob. 4PCh. 6 - Design a PLC program and prepare a typical I/O...Ch. 6 - Prob. 6PCh. 6 - Prob. 7PCh. 6 - Prob. 8P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- What is the difference between modes of operation (run,prog,rem)in plcarrow_forwardDevelop a PLC-based ladder logic program for automatic packaging system: 1.Draw and explain ladder logic diagram to run a conveyor motor using the following conditions: a.AND Logic Function b.NOR Logic Function Analyze the following conditions: a.Upgrade the ladder diagram such that the motor runs in both clockwise and anti-clockwise direction. b.Use two light indicators to indicate the direction of motor rotation. c.Use a photosensor to detect the package on the conveyor d.Add start stop logic (Use both AND logic and OR logic, where necessary use switches to control the direction)arrow_forwardDraw a plc ladder diagram for blinking lights with start and stop button. Please help me with this. Thank you in advanced.arrow_forward
- Design a PLC program and prepare a typical I/O connection diagram and ladder logic program for the airplane ( or aircraft ).arrow_forwardA PLC is used to control a single-axis robot, in which the axis is driven by a pneumatic cylinder. An output signal to the pneumatic cylinder causes it to extend (ON state). When there is no signal, the pneumatic cylinder retracts (OFF state). The gripper is an also driven by a pneumatic cylinder. The gripper open position is an OFF state and the closed position is an ON state. In order to perform a task, the following sequence of operations must be performed: TH Sequence No. Аxis Gripper OFF OFF 1 ON OFF ON ON 3 OFF ON 4 OFF OFF The process begins when the start bush button is ON and a part triggers a limit switch. For safety, an emergency switch is used to shut off the entire system. Design a PLC ladder diagram for this application.arrow_forwardDraw a ladder diagram in PLC programming for manually operated standing A+B+B-A- cylinder sequence.arrow_forward
- Create a PLC ladder logic diagram for an alarm that turns on when either A counts up to 10, or B counts down to 7.arrow_forwardCompile the PLC program Compile the PLC program using Ladder logic on Codesys or Logix Pro for the Traffic light change over as described in the Problem statement. Capture the Screenshots of the Ladder logic program as well the run sequences of the program and list it below with the explanation of the actions in line with the requirements for the Traffic light problem statementarrow_forwardStepper motor control using ULN2003 IC in 16F877 microcontroller will be carried out. In the program, stepper motor and driver IC will be connected to PORTD. to RA0 pin When the connected button is pressed, the stepper motor will turn to the left with half a step and one speed, to pin RA1. When the connected button is pressed, the motor will turn to the right at a certain speed. button connected to RA2 pin When pressed, the motor will be stopped no matter which direction it turns. During engine operation (right or left) If the button connected to the RA3 pin is pressed, the motor speed will double. Working logic Write the program described (solve with ccs)arrow_forward
- ROBLEM: Control 2 double acting cylinders using one push button for start and one push button for stop. The repetitive cycle is as follows: Extend C1, after 5 seconds extend C2, after 5 seconds retract C1, after 5 seconds retract C2 All the process stops when the cycle repeats itself 5 times (counter) in a row. (Use CTD counter) I – Conduct the experiment with Codesys PLC module or online PLC simulator. () II- Simulate the process with I/O, and evaluate the outputs. () III- Make suitable connections for the pneumatic circuit and PLC, run the simulation and get the output verified. IV-Interpret the output of the PLC program with respect to its function.arrow_forward1. Briefly describe the difference between the different types of counter modules used for PLCs. 2. Design a ladder logic program for a traffic light intersection. Use timers to control the duration of the green, yellow, and red lights for each direction.arrow_forward5 lamps are lit at intervals of 2 seconds with the start button. When all 5 lamps are lit, it waits for 5 seconds and continues to light up with 2 second intervals from the 1st lamp. If sensor 1 is active while lamp 1 is on, lamp 3 will continue to operate as above, without lamp number 2 turning on. with stop buttonlamps will be turned off at any time.draw the plc ladder diagram accordingly.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Database System ConceptsComputer ScienceISBN:9780078022159Author:Abraham Silberschatz Professor, Henry F. Korth, S. SudarshanPublisher:McGraw-Hill Education
Starting Out with Python (4th Edition)Computer ScienceISBN:9780134444321Author:Tony GaddisPublisher:PEARSON
Digital Fundamentals (11th Edition)Computer ScienceISBN:9780132737968Author:Thomas L. FloydPublisher:PEARSON
C How to Program (8th Edition)Computer ScienceISBN:9780133976892Author:Paul J. Deitel, Harvey DeitelPublisher:PEARSON
Database Systems: Design, Implementation, & Manag...Computer ScienceISBN:9781337627900Author:Carlos Coronel, Steven MorrisPublisher:Cengage Learning
Programmable Logic ControllersComputer ScienceISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Database System Concepts
Computer Science
ISBN:9780078022159
Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan
Publisher:McGraw-Hill Education
Starting Out with Python (4th Edition)
Computer Science
ISBN:9780134444321
Author:Tony Gaddis
Publisher:PEARSON
Digital Fundamentals (11th Edition)
Computer Science
ISBN:9780132737968
Author:Thomas L. Floyd
Publisher:PEARSON
C How to Program (8th Edition)
Computer Science
ISBN:9780133976892
Author:Paul J. Deitel, Harvey Deitel
Publisher:PEARSON
Database Systems: Design, Implementation, & Manag...
Computer Science
ISBN:9781337627900
Author:Carlos Coronel, Steven Morris
Publisher:Cengage Learning
Programmable Logic Controllers
Computer Science
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education