Programmable Logic Controllers
5th Edition
ISBN: 9780073373843
Author: Frank D. Petruzella
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Question
Chapter 6, Problem 2P
Program Plan Intro
Break-make pushbutton switch:
- Break-before-make pushbutton is a switch whose top level section contacts are Normally Closed (NC) and bottom level section contacts are Normally Open (NO).
- The top level contacts will be opened before the bottom level contacts get closed when the pushbutton is pressed.
- An electrical symbol used to represent break-make pushbutton switch is given below.
Given:
The conventional hardwired relay circuit should perform the following circuit functions when two break-make pushbuttons are used.
- The light L1 must turn ON when pushbutton PB1 is pressed.
- The light L2 must turn ON when pushbutton PB2 is pressed.
- The pushbuttons must be interlocked electrically, such that L1 and L2 cannot be turned ON simultaneously.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Construct a basic stop/start seal-in circuit. Energize an internal relay to seal-in (latch) the circuit. write the circuit in both Ladder Logic and Function Block Diagram (FBD).
Hardware setup:
Input 1 - Normally closed stop pushbutton,
Input 2 - Normally open start pushbutton.
Output 1 - A Red light to indicate the circuit is not energized.
Output 2 - A Green light to indicate the circuit is energized.
Label all inputs and outputs in the plc program.
Write the program in both ladder and function block diagram (FBD).
build a full adder circuit with I/O switched on input wires, LEDs on output and naming input and output wires properly
Design an appropriate combinational circuit that implements a digital system with the following output functions an AC remote: ON, OFF, MODE, SHIFT, FAN, SMART, SWING, ECO using a decoder.
Chapter 6 Solutions
Programmable Logic Controllers
Ch. 6 - Prob. 1RQCh. 6 - Prob. 2RQCh. 6 - Prob. 3RQCh. 6 - Prob. 4RQCh. 6 - Prob. 5RQCh. 6 - Prob. 6RQCh. 6 - Prob. 7RQCh. 6 - Prob. 8RQCh. 6 - What do the abbreviations NO and NC represent when...Ch. 6 - Prob. 10RQ
Ch. 6 - Prob. 11RQCh. 6 - Prob. 12RQCh. 6 - Compare the operation of a photovoltaic solar cell...Ch. 6 - What are the two basic components of a...Ch. 6 - Prob. 15RQCh. 6 - Give an explanation of how a scanner and a decoder...Ch. 6 - Prob. 17RQCh. 6 - Prob. 18RQCh. 6 - Prob. 19RQCh. 6 - Prob. 20RQCh. 6 - Prob. 21RQCh. 6 - Prob. 22RQCh. 6 - Prob. 23RQCh. 6 - Prob. 24RQCh. 6 - Prob. 25RQCh. 6 - Prob. 26RQCh. 6 - Prob. 27RQCh. 6 - Prob. 28RQCh. 6 - Prob. 29RQCh. 6 - Prob. 30RQCh. 6 - Prob. 31RQCh. 6 - Prob. 32RQCh. 6 - Prob. 33RQCh. 6 - Prob. 1PCh. 6 - Prob. 2PCh. 6 - Prob. 3PCh. 6 - Prob. 4PCh. 6 - Design a PLC program and prepare a typical I/O...Ch. 6 - Prob. 6PCh. 6 - Prob. 7PCh. 6 - Prob. 8P
Knowledge Booster
Similar questions
- The input waveform shown in the figure below is applied to an inverter, which is used to operate a light on a control circuit. Draw the timing diagram of the output waveform in proper relation to the input. VIN HIGH LOW urrarrow_forwardIn a certain chemical-processing plant, a liquid chemical is used in a manufacturing process. The chemical is stored in three different tanks. A level sensor in each tank produces a HIGH voltage when the level of chemical in the tank drops below a specified point. Design a circuit that monitors the chemical level in each tank and indicates when the level in any two of the tanks drops below the specified point.arrow_forward3. Complete the timing diagram for the following circuit: ENABLE CLK IN ENABLE IN MUX_OUT For ENABLE = 0, MUX_OUT = IN CLK MUX_OUT SET D Q CLR Q U Uarrow_forward
- Stepper motor control using ULN2003 IC in 16F877 microcontroller will be carried out. In the program, stepper motor and driver IC will be connected to PORTD. to RA0 pin When the connected button is pressed, the stepper motor will turn to the left with half a step and one speed, to pin RA1. When the connected button is pressed, the motor will turn to the right at a certain speed. button connected to RA2 pin When pressed, the motor will be stopped no matter which direction it turns. During engine operation (right or left) If the button connected to the RA3 pin is pressed, the motor speed will double. Working logic Write the program described (solve with ccs)arrow_forward1. Design a combinational circuit that takes four inputs (Ē (the enable), A, B, and C), has four outputs (X, Y, Z, and EoS (the end of Sequence flag)) and meets the following specifications. 1. If ABC = 111 then, regardless of the value of E, the end of sequence flag EoS = 1 else EoS = 0. 2. If E' = 1 then XYZ = ABC. 3. If E' = 0 and ABC ‡ 111 then XYZ should be set to the code following the value of ABC in this list: 000, 100, 101, 001, 011, 010, 110, 111. For example, if ABC = 010 then XYZ = 110. This is a type of Gray code sequence (A Gray code is an encoding of numbers so that adjacent numbers have a single digit differing by 1) 4. If E' = 0 and ABC = 111, then XYZ may be set to anything (this is called a "don't care" and should be represented in the truth tables and K-maps with an X.) a. Draw a truth table (with the operands in this order E', A, B, C, X, Y, Z, EOS) for this combinational circuit's function. To get you startedarrow_forward1. Design and implement a circuit using positive edge triggered DFFs that generates a pulse (p = 1) on the 2nd, 3rd, 5th, and 7th clock cycles after initialization. The sequence should repeat every 8 clock pulses. Include an asynchronous reset signal. 1.1 Implement your design in Verilog (behavioral)arrow_forward
- 10. Consider you are interfacing a switch and two LEDS (L1 and L2) with LPC1769 MCU. • When the switch is ON (logic HIGH), LI is ON, and L2 is OFF. • When the switch is OFF (logic LOW), L1 is OFF, and L2 is ON. • Switch is interfaced with port 1- pin 2, L1 with port 1- pin 3, and L2 with port 1- pin 4. • Initially L1 is ON, and L2 is OFF. Complete the C program template for this task given below. Demonstrate all steps: Pin function configuration, mode selection, and writing/reading of pin values correctly. #include int main (void)arrow_forwardA microcontroller of PIC16F84A and a 7-segment LED are used to form an down- count counter from 9 to 0. The input devices and 7-segment LED on the operation panel are shown in Figure 3.1 while the related electronic circuit and Flowcode program are as shown in Figures 3.2 and 3.3, respectively. Answer the following questions if the counter is operated at high level input voltage those are controlled by the input devices for the data input and stop functions. Count Stop LED Counter Figure 3.1 A countdown counter using 7-segment LED Count (1) X1 U1 16 15 17 OSCICLKIN oscziCLKOUT RAD RA1 18 Stop RAZ RAS RAATOCKI 4 MCLR 4MHZ CRYSTAL C1 C2 RBOINT RB1 RB2 RB3 RB4 RBS RB6 RB7 22pF PIC16F84A SV RO Figure 3.2 Electronic cireuit for the counter -lelalarrow_forwardDesign a combinational circuit with four inputs, w, x, y, and z, and four outputs, A, B, C and D. When the binary input is 0, 1, 2, 3, 4,5,6 the binary output is two greater than the input. When the binary input is 7,8, 9, 10, 12,13,14,15 the binary output is three less than the input.arrow_forward
- Using the sim8085 write the following code: In a sensor network, three pressure sensors are connected which gives the reading of 4 psi, 8 psi and 10 psi. All the sensor readings are to be summed up and store as a single readingarrow_forward3. Design and implement a circuit using positive edge triggered DFFS that generates a pulse (p = 1) on the 2nd, 3rd, 5th, and 7th clock cycles after initialization. The sequence should repeat every 8 clock pulses. Include an asynchronous reset signal. %3!arrow_forwardIV. PROCEDURES: For the AND gate look on the data sheets, connect the circuit on Breadboard and test the gate. Using logic switches SW1 and SW2, apply the logic levels 0 and 1 to gate inputs Create a truth table and record the results Also simulate the given gate using the Circuit Wizard simulation software Obtain the corresponding circuit diagram using the simulation software of the Boolean expression F((A,B,C)= АВ* AC * ВС From the obtain circuit diagram develop the corresponding truth table From the figure below obtain the equivalent Boolean expression and develop its corresponding truth Table АП сПо- Boolean Expression: Z= (AB)(CD)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Database System ConceptsComputer ScienceISBN:9780078022159Author:Abraham Silberschatz Professor, Henry F. Korth, S. SudarshanPublisher:McGraw-Hill Education
Starting Out with Python (4th Edition)Computer ScienceISBN:9780134444321Author:Tony GaddisPublisher:PEARSON
Digital Fundamentals (11th Edition)Computer ScienceISBN:9780132737968Author:Thomas L. FloydPublisher:PEARSON
C How to Program (8th Edition)Computer ScienceISBN:9780133976892Author:Paul J. Deitel, Harvey DeitelPublisher:PEARSON
Database Systems: Design, Implementation, & Manag...Computer ScienceISBN:9781337627900Author:Carlos Coronel, Steven MorrisPublisher:Cengage Learning
Programmable Logic ControllersComputer ScienceISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Database System Concepts
Computer Science
ISBN:9780078022159
Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan
Publisher:McGraw-Hill Education
Starting Out with Python (4th Edition)
Computer Science
ISBN:9780134444321
Author:Tony Gaddis
Publisher:PEARSON
Digital Fundamentals (11th Edition)
Computer Science
ISBN:9780132737968
Author:Thomas L. Floyd
Publisher:PEARSON
C How to Program (8th Edition)
Computer Science
ISBN:9780133976892
Author:Paul J. Deitel, Harvey Deitel
Publisher:PEARSON
Database Systems: Design, Implementation, & Manag...
Computer Science
ISBN:9781337627900
Author:Carlos Coronel, Steven Morris
Publisher:Cengage Learning
Programmable Logic Controllers
Computer Science
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education