Programmable Logic Controllers
5th Edition
ISBN: 9780073373843
Author: Frank D. Petruzella
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Expert Solution & Answer
Chapter 6, Problem 6RQ
Explanation of Solution
a.
Schematic diagram of AC magnetic motor starter:
The schematic diagram for an across-the-line AC magnetic motor starter is given below:
Explanation:
- The above given schematic is of a three phase magnetic motor starter as AC signals mostly prefer three phase system...
Explanation of Solution
b.
i) Function of main contact M:
- The main contact M is placed in series with the motor.
- It is used to complete the path to the motor.
- It is a part of the power circuit and is built in such a way that it could handle full load current of motor.
ii) Function of control contact M:
- The control contact M is placed parallel to the start button.
- It is provided with an address similar to that of the starter coil M.
- It is used to keep continuity in path from left end of the rail to starter coil M, even though the start button is released.
- It is more than enough to handle small amount of current that is needed to energize the coil.
iii) Function of starter coil M:
- The starter coil M is placed in series to the start button...
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Design one system with apply the electrical transducer in the
system. Explain about the concept and function of the transducer
in the system. (Student can choose any type of transducer).
1. Given ADC0804 and eight LEDS, design an ADC test circuit.
Eight LEDS are connected to eight outputs of the ADC,
respectively. The output is all 1's when the analog input is
5.1v, and all 0's when the input is Ov. Calculate and make a
table indicating analog voltage ranges which correspond to
digital number: 00H, 08H, 80H, 88H, and FFH.
Problem 5. Write the Boolean expression (in Sum of Products form) for the logic circuit
that will have a 1 output when X = 0, Y = 0, Z = 1 and X = 1, Y = 1, Z = 0, and a zero (0)
output for all other input states. Draw the logic diagram for this circuit.
Chapter 6 Solutions
Programmable Logic Controllers
Ch. 6 - Prob. 1RQCh. 6 - Prob. 2RQCh. 6 - Prob. 3RQCh. 6 - Prob. 4RQCh. 6 - Prob. 5RQCh. 6 - Prob. 6RQCh. 6 - Prob. 7RQCh. 6 - Prob. 8RQCh. 6 - What do the abbreviations NO and NC represent when...Ch. 6 - Prob. 10RQ
Ch. 6 - Prob. 11RQCh. 6 - Prob. 12RQCh. 6 - Compare the operation of a photovoltaic solar cell...Ch. 6 - What are the two basic components of a...Ch. 6 - Prob. 15RQCh. 6 - Give an explanation of how a scanner and a decoder...Ch. 6 - Prob. 17RQCh. 6 - Prob. 18RQCh. 6 - Prob. 19RQCh. 6 - Prob. 20RQCh. 6 - Prob. 21RQCh. 6 - Prob. 22RQCh. 6 - Prob. 23RQCh. 6 - Prob. 24RQCh. 6 - Prob. 25RQCh. 6 - Prob. 26RQCh. 6 - Prob. 27RQCh. 6 - Prob. 28RQCh. 6 - Prob. 29RQCh. 6 - Prob. 30RQCh. 6 - Prob. 31RQCh. 6 - Prob. 32RQCh. 6 - Prob. 33RQCh. 6 - Prob. 1PCh. 6 - Prob. 2PCh. 6 - Prob. 3PCh. 6 - Prob. 4PCh. 6 - Design a PLC program and prepare a typical I/O...Ch. 6 - Prob. 6PCh. 6 - Prob. 7PCh. 6 - Prob. 8P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.Similar questions
- A current-carrying wire has current in the downward direction. An external magnetic field is applied, with direction as shown the figure (into the screen). What will be the direction of the force experienced by the wire? Figure for Problem 2 X X X X B X X X a. Clockwise b. Counterclockwise C. To the left d. To the right e. Information is insufficient. x X X Xarrow_forwardQ2: For the circuit shown in below, use (matlab, c++, or python) and Nodal Analysis to: a) Find the voltage across the current source 11 terminals b) Find the current through the resistance R1 c) Find the real and reactive Powers delivered by the current source 11 Find the real and reactive Powers consumed by the capacitor C2 d) 11 10 A RMS 50 Hz +35 Deg Z1 AM R2 402 Z4 R4 80 m Z2 L2 15 mH 12 7A RMS 50 Hz +74 Deg Zc1 C1 150 F R3 30 www w R6 40 Z6 L3 25 mH E1 100 V RMS - 40 Deg Z5 50 Hz www R5 20 Zc2 C2 200 Farrow_forwardQ. Refer to the given figures (a) and (b). A logic analyzer is used to check the circuit in figure (a) and displays the waveforms shown in figure (b). The actual analyzer display shows all four data outputs, Q0-Q3. The analyzer's cursor is placed at position X and all four of the data output lines show a LOW level output. What is wrong, if anything, with the circuit? A. Nothing is wrong, according to the display. The outputs are in the open state and should show zero output voltage. B. The circuit is in the READ mode and the outputs, Q0-Q3, should reflect the contents of the memory at that address. The chip is defective; replace the chip. C. The circuit is in the mode and should be writing the contents of the selected address to Q0-Q3. D. The Q0-Q3 lines can be either LOW or HIGH, since the chip is in the tristate mode in which case their level is unpredictable Elert - RAM 1 AO 1 A1 O A2 O A3 1 A4 O A5 1 A6 1 A7 256 X 4 A0-A7 R/W A 255 CS QO Q1 Q2 DO-D3 O DO 1 D1 O D2 1 D3 Q0-Q3 Y W O…arrow_forward
- A silicon diode with a saturation current 12 pA in the reversedirection is used at room temperature in a circuit as shown inthe figure. If the source voltage is 4 volts and the currentthrough the circuit is 1 mA.a. Find the resistance value in the circuit ?b. Find the voltage drop across the diode?arrow_forwardDesign or Implement a Simple Digital System which includes: 1. A few brief paragraphs explaining the functionality of the system. 2. A logic gate schematic of one or more of the functional blocks. 3. A block diagram of the system. 4. A Boolean algebra expression of a part of the system or the entire system. 5. And Karnaugh map simplification of a part of the system or the entire system. 6. Implement one of your logic gates or functional blocks using an HDL such as VHDL or Verilog.arrow_forwardDraw the full pneumatic and ladder diagram of the sequence operation given below. Also, draw the positioning of your sensor in every cylinder. A+, B+, B-, C+, A-, C-arrow_forward
- Design a combinational circuit with four inputs— A, B, C, and D —and one output, F . F is to be equal to 1when A = 1, provided that B = 0, or when B = 1, provided that either C or D is also equal to 1. Otherwise,the output is to be equal to 0.1. Obtain the truth table of the circuit.2. Simplify the output function.3. Draw the logic diagram of the circuit, using NAND gates with a minimum number of ICs.4. Construct the circuit and test it for proper operation by verifying the given conditions.arrow_forwardMake a Seven-Segment electrical circuit on Proteus with outputs and inputs as follows:arrow_forwardDesign the circuit for Traffic light controller for 6 streets, and: 1-(including function, inputs/outputs, logic elements required etc), Truth table/State Table,Boolean equations, Simplification of the equations. Attach an image of the Logisim circuit 2-arrow_forward
- 4. Draw a JK Flip Flop circuit configured to automatically toggle between the outputs every 0.5 seconds. On what settings and inputs did you draw to cause this to happen? 5. Draw a graph to express function of the output Q in the previous question. Let the independent variable be time elapsed (seconds) and the dependent variable be voltage level (V). What does this graph resemble?arrow_forwardDevelop a PLC-based ladder logic program for automatic packaging system: 1.Draw and explain ladder logic diagram to run a conveyor motor using the following conditions: a.AND Logic Function b.NOR Logic Function Analyze the following conditions: a.Upgrade the ladder diagram such that the motor runs in both clockwise and anti-clockwise direction. b.Use two light indicators to indicate the direction of motor rotation. c.Use a photosensor to detect the package on the conveyor d.Add start stop logic (Use both AND logic and OR logic, where necessary use switches to control the direction)arrow_forward4. In a series circuit with 10V applied: A. The greater the total resistance, the less the total current B. The greater the total current, the greater the total resistance C. The IR voltage drops will each equal 10V D. The sum of the IR voltage drops will equal 10V 5. When an IR voltage drop exists in a series circuit : A. The polarity of the resistor is equal to positive B. The polarity of the resistor is equal to negative C. The polarity of the resistor is less than the total current on both sides D. The polarity of the resistor is positive on one end and negative on the other because of current flowing through itarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Database System ConceptsComputer ScienceISBN:9780078022159Author:Abraham Silberschatz Professor, Henry F. Korth, S. SudarshanPublisher:McGraw-Hill Education
Starting Out with Python (4th Edition)Computer ScienceISBN:9780134444321Author:Tony GaddisPublisher:PEARSON
Digital Fundamentals (11th Edition)Computer ScienceISBN:9780132737968Author:Thomas L. FloydPublisher:PEARSON
C How to Program (8th Edition)Computer ScienceISBN:9780133976892Author:Paul J. Deitel, Harvey DeitelPublisher:PEARSON
Database Systems: Design, Implementation, & Manag...Computer ScienceISBN:9781337627900Author:Carlos Coronel, Steven MorrisPublisher:Cengage Learning
Programmable Logic ControllersComputer ScienceISBN:9780073373843Author:Frank D. PetruzellaPublisher:McGraw-Hill Education
Database System Concepts
Computer Science
ISBN:9780078022159
Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan
Publisher:McGraw-Hill Education
Starting Out with Python (4th Edition)
Computer Science
ISBN:9780134444321
Author:Tony Gaddis
Publisher:PEARSON
Digital Fundamentals (11th Edition)
Computer Science
ISBN:9780132737968
Author:Thomas L. Floyd
Publisher:PEARSON
C How to Program (8th Edition)
Computer Science
ISBN:9780133976892
Author:Paul J. Deitel, Harvey Deitel
Publisher:PEARSON
Database Systems: Design, Implementation, & Manag...
Computer Science
ISBN:9781337627900
Author:Carlos Coronel, Steven Morris
Publisher:Cengage Learning
Programmable Logic Controllers
Computer Science
ISBN:9780073373843
Author:Frank D. Petruzella
Publisher:McGraw-Hill Education