Fluid Mechanics
8th Edition
ISBN: 9780073398273
Author: Frank M. White
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 6, Problem 6.11P
Water at 20°C flows upward at 4 m/s in a 6-cm-diameter pipe. The pipe length between points 1 and 2 is 5 m, and point 2 is 3 m higher. A mercury manometer, connected between 1 and 2, has a reading h = 135 mm, with p1 higher. (a) What is the pressure change
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A pitot-static tube is used for measuring the air velocity, as shown in the figure below. The pitot-static tube is connected to a U-
tube manometer containing a liquid of specific gravity SG = 0.9 which indicates a difference of head of H=4 cm of the liquid.
What is the air velocity V? The density of water and air is 1000 kg/m³ and 1.2 kg/m³, respectively, and the gravitational
acceleration g is 9.81 m/s².
1. [23.51755348, 24.97224751 m/s.
V=
Air
Velocity V
Pitot-static
probe
Liquid of Specific
Gravity SG
H
9
For the traditional equal-level manometer measurement inFig. E2.3, water at 20 ° C fl ows through the plug devicefrom a to b . The manometer fl uid is mercury. If L= 12 cmand h= 24 cm, ( a ) what is the pressure drop through thedevice? ( b ) If the water fl ows through the pipe at a velocityV =18 ft/s, what is the dimensionless loss coeffi cient ofthe device, defi ned by K = ∆ p /( ρ V 2 )?
Water fl ows upward in a pipe slanted at 30 ° , as in Fig. .The mercury manometer reads h =12 cm. Both fl uidsare at 20° C. What is the pressure difference p 1 - p 2 inthe pipe?
Chapter 6 Solutions
Fluid Mechanics
Ch. 6 - Prob. 6.1PCh. 6 - The present pumping rate of crude oil through the...Ch. 6 - The Keystone Pipeline in the chapter opener photo...Ch. 6 - For flow of SAE 30 oil through a 5-cm-diameter...Ch. 6 - In flow past a body or wall, early transition to...Ch. 6 - P6.6 For flow of a uniform stream parallel to a...Ch. 6 - SAE 10W30 oil at 20°C flows from a tank into a...Ch. 6 - P6.8 When water at 20°C is in steady turbulent...Ch. 6 - A light liquid 950kg/m3 flows at an average...Ch. 6 - Water at 20°C flows through an inclined...
Ch. 6 - Water at 20°C flows upward at 4 m/s in a...Ch. 6 - Prob. 6.12PCh. 6 - Prob. 6.13PCh. 6 - Prob. 6.14PCh. 6 - Prob. 6.15PCh. 6 - Prob. 6.16PCh. 6 - P6.17 A capillary viscometer measures the time...Ch. 6 - P6.18 SAE 50W oil at 20°C flows from one tank to...Ch. 6 - Prob. 6.19PCh. 6 - The oil tanks in Tinyland are only 160 cm high,...Ch. 6 - Prob. 6.21PCh. 6 - Prob. 6.22PCh. 6 - Prob. 6.23PCh. 6 - Prob. 6.24PCh. 6 - Prob. 6.25PCh. 6 - Prob. 6.26PCh. 6 - Let us attack Prob. P6.25 in symbolic fashion,...Ch. 6 - Prob. 6.28PCh. 6 - Prob. 6.29PCh. 6 - Prob. 6.30PCh. 6 - A laminar flow element (LFE) (Meriam Instrument...Ch. 6 - SAE 30 oil at 20°C flows in the 3-cm.diametcr pipe...Ch. 6 - Prob. 6.33PCh. 6 - Prob. 6.34PCh. 6 - In the overlap layer of Fig. 6.9a, turbulent shear...Ch. 6 - Prob. 6.36PCh. 6 - Prob. 6.37PCh. 6 - Prob. 6.38PCh. 6 - Prob. 6.39PCh. 6 - Prob. 6.40PCh. 6 - P6.41 Two reservoirs, which differ in surface...Ch. 6 - Prob. 6.42PCh. 6 - Prob. 6.43PCh. 6 - P6.44 Mercury at 20°C flows through 4 m of...Ch. 6 - P6.45 Oil, SG = 0.88 and v = 4 E-5 m2/s, flows at...Ch. 6 - Prob. 6.46PCh. 6 - Prob. 6.47PCh. 6 - Prob. 6.48PCh. 6 - Prob. 6.49PCh. 6 - Prob. 6.50PCh. 6 - Prob. 6.51PCh. 6 - Prob. 6.52PCh. 6 - Water at 2OC flows by gravity through a smooth...Ch. 6 - A swimming pool W by Y by h deep is to be emptied...Ch. 6 - Prob. 6.55PCh. 6 - Prob. 6.56PCh. 6 - Prob. 6.57PCh. 6 - Prob. 6.58PCh. 6 - P6.59 The following data were obtained for flow of...Ch. 6 - Prob. 6.60PCh. 6 - Prob. 6.61PCh. 6 - Water at 20°C is to be pumped through 2000 ft of...Ch. 6 - Prob. 6.63PCh. 6 - Prob. 6.64PCh. 6 - Prob. 6.65PCh. 6 - Prob. 6.66PCh. 6 - Prob. 6.67PCh. 6 - Prob. 6.68PCh. 6 - P6.69 For Prob. P6.62 suppose the only pump...Ch. 6 - Prob. 6.70PCh. 6 - Prob. 6.71PCh. 6 - Prob. 6.72PCh. 6 - Prob. 6.73PCh. 6 - Prob. 6.74PCh. 6 - Prob. 6.75PCh. 6 - P6.76 The small turbine in Fig. P6.76 extracts 400...Ch. 6 - Prob. 6.77PCh. 6 - Prob. 6.78PCh. 6 - Prob. 6.79PCh. 6 - The head-versus-flow-rate characteristics of a...Ch. 6 - Prob. 6.81PCh. 6 - Prob. 6.82PCh. 6 - Prob. 6.83PCh. 6 - Prob. 6.84PCh. 6 - Prob. 6.85PCh. 6 - SAE 10 oil at 20°C flows at an average velocity of...Ch. 6 - A commercial steel annulus 40 ft long, with a = 1...Ch. 6 - Prob. 6.88PCh. 6 - Prob. 6.89PCh. 6 - Prob. 6.90PCh. 6 - Prob. 6.91PCh. 6 - Prob. 6.92PCh. 6 - Prob. 6.93PCh. 6 - Prob. 6.94PCh. 6 - Prob. 6.95PCh. 6 - Prob. 6.96PCh. 6 - Prob. 6.97PCh. 6 - Prob. 6.98PCh. 6 - Prob. 6.99PCh. 6 - Prob. 6.100PCh. 6 - Prob. 6.101PCh. 6 - *P6.102 A 70 percent efficient pump delivers water...Ch. 6 - Prob. 6.103PCh. 6 - Prob. 6.104PCh. 6 - Prob. 6.105PCh. 6 - Prob. 6.106PCh. 6 - Prob. 6.107PCh. 6 - P6.108 The water pump in Fig. P6.108 maintains a...Ch. 6 - In Fig. P6.109 there are 125 ft of 2-in pipe, 75...Ch. 6 - In Fig. P6.110 the pipe entrance is sharp-edged....Ch. 6 - For the parallel-pipe system of Fig. P6.111, each...Ch. 6 - Prob. 6.112PCh. 6 - Prob. 6.113PCh. 6 - Prob. 6.114PCh. 6 - Prob. 6.115PCh. 6 - Prob. 6.116PCh. 6 - Prob. 6.117PCh. 6 - Prob. 6.118PCh. 6 - Prob. 6.119PCh. 6 - Prob. 6.120PCh. 6 - Prob. 6.121PCh. 6 - Prob. 6.122PCh. 6 - Prob. 6.123PCh. 6 - Prob. 6.124PCh. 6 - Prob. 6.125PCh. 6 - Prob. 6.126PCh. 6 - Prob. 6.127PCh. 6 - In the five-pipe horizontal network of Fig....Ch. 6 - Prob. 6.129PCh. 6 - Prob. 6.130PCh. 6 - Prob. 6.131PCh. 6 - Prob. 6.132PCh. 6 - Prob. 6.133PCh. 6 - Prob. 6.134PCh. 6 - An airplane uses a pitot-static tube as a...Ch. 6 - Prob. 6.136PCh. 6 - Prob. 6.137PCh. 6 - Prob. 6.138PCh. 6 - P6.139 Professor Walter Tunnel needs to measure...Ch. 6 - Prob. 6.140PCh. 6 - Prob. 6.141PCh. 6 - Prob. 6.142PCh. 6 - Prob. 6.143PCh. 6 - Prob. 6.144PCh. 6 - Prob. 6.145PCh. 6 - Prob. 6.146PCh. 6 - Prob. 6.147PCh. 6 - Prob. 6.148PCh. 6 - Prob. 6.149PCh. 6 - Prob. 6.150PCh. 6 - Prob. 6.151PCh. 6 - Prob. 6.152PCh. 6 - Prob. 6.153PCh. 6 - Prob. 6.154PCh. 6 - Prob. 6.155PCh. 6 - Prob. 6.156PCh. 6 - Prob. 6.157PCh. 6 - Prob. 6.158PCh. 6 - Prob. 6.159PCh. 6 - Prob. 6.160PCh. 6 - Prob. 6.161PCh. 6 - Prob. 6.162PCh. 6 - Prob. 6.163PCh. 6 - Prob. 6.1WPCh. 6 - Prob. 6.2WPCh. 6 - Prob. 6.3WPCh. 6 - Prob. 6.4WPCh. 6 - Prob. 6.1FEEPCh. 6 - Prob. 6.2FEEPCh. 6 - Prob. 6.3FEEPCh. 6 - Prob. 6.4FEEPCh. 6 - Prob. 6.5FEEPCh. 6 - Prob. 6.6FEEPCh. 6 - Prob. 6.7FEEPCh. 6 - Prob. 6.8FEEPCh. 6 - Prob. 6.9FEEPCh. 6 - Prob. 6.10FEEPCh. 6 - Prob. 6.11FEEPCh. 6 - Prob. 6.12FEEPCh. 6 - Prob. 6.13FEEPCh. 6 - Prob. 6.14FEEPCh. 6 - Prob. 6.15FEEPCh. 6 - Prob. 6.1CPCh. 6 - Prob. 6.2CPCh. 6 - Prob. 6.3CPCh. 6 - Prob. 6.4CPCh. 6 - Prob. 6.5CPCh. 6 - Prob. 6.6CPCh. 6 - Prob. 6.7CPCh. 6 - Prob. 6.8CPCh. 6 - Prob. 6.9CPCh. 6 - A hydroponic garden uses the 10-m-long...Ch. 6 - It is desired to design a pump-piping system to...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A pipeline with roughness ks = 1.0mm and diameter D = 8.8cm connects two reservoirs. The reservoirs are both open to the atmosphere and differ in surface elevation by H = 40m. The two reservoirs with the connecting pipe are shown in the figure below. You can assume density of water = 1003kg/m³, dynamic viscosity of water = 0.001Pas and acceleration due to gravity 9.81m/s². Local losses must be considered; assume reasonable values as introduced in the ENGG2500 lectures. Reservoir 1 = Pipe with: D,K, m. H a) What is the friction factor of the pipe for a flow rate of Q =44L/s? Provide your answer to 3 decimal places. The friction factor f = = b) For this case, what is the length of the pipe? Provide your answer to 3 decimal places. The length is L Reservoir 2arrow_forwardWater flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 12 in. The atmospheric pressure is 14.7 Ibf/in?, the specific volume of water is 0.01604 ft/lb, and the acceleration of gravity is g = 32.0 ft/s?. Patm = 14.7 Ibr/in.? g = 32.0 ft/s² Water v = 0.01604 ft/lb Determine the difference in pressure between points a and b, in Ibf/in2?. Does the pressure increase or decrease from point a to point b? Sten 1arrow_forwardA pipe is horizontal and carries oil that has a viscosity of 0.14 Pa s. The volume flow rate of the oil is 5.3 × 10^-5 m3/s. The length of the pipe is 38 m, and its radius is 0.57 cm. At the output end of the pipe the pressure is atmospheric pressure. What is the absolute pressure at the input end?arrow_forward
- Water flows steadily downward along a pipe that is inclined at 30° below the horizontal, as shown. Pressure difference P4-PB is due partly to gravity and partly to friction. Evaluate the pressure difference if L = 1.5 m and h = 15 cm. Use p= 1000 kg/m3 and u = 1.12 x 103 Ns/m2 for the water and p= 13600 kg/m³ and u = 1.57 x 103 Ns/m? for the mercury. L Water 30°7 Mercury harrow_forwardWater flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 12 in. The atmospheric pressure is 14.7 Ibf/in?, the specific volume of water is 0.01604 ft3/lb, and the acceleration of gravity is g = 32.0 ft/s?. Patm = 14.7 Ibf/in.? g = 32.0 ft/s² Water v = 0.01604 ft³/lb Determine the difference in pressure between points a and b, in Ibf/in?. Does the pressure increase or decrease from point a to point b?arrow_forwardThe pressure drop (Ap) test is carried out using a pipe configuration as illustrated below: Manometer 1 Manometer 2 straight pipe D= 2R R= radius in pipe The pipe data and the flowing fluid are as follows: Pipe: D = 1 cm; L= 100 cm. Fluid: Water, with density (A) = 1000 kg/m"; absolute viscosity (u) = 0.001 kg/im.s); Experimental data is shown as shown in the following table: Task: Ja. Plot the graph of the pressure as a function of the average velocity (V.v). b. Based on the equation for laminar flow in the pipe as follows: Ap = 32VuL, Vavg (m/s) Ap (Pa) 0,001 0,002 0,005 0,01 0,02 0,04 0,06 0,08 0,1 0,12 0,15 0,30 0,62 1,61 3,10 6,10 12,10 20,10 26,00 32,50 38,90 47,20 D Compare the experimental results in the table with the results of calculations using the above equation. Leave a comment. Note: Ap = p1-p2. c. The coefficient of friction (f) in the pipe is formulated as follows: f- 2DAD PL(V.) plot (plot) this distribution of fas a function of the Reynolds number (Re). Re is…arrow_forward
- 1. In the benzene plant, the pressure drop at some point of a pipeline in which benzene is passing through is measured with a U-tube manometer (Rm,1) as 10 cm (1st situation). The manometer fluid is carbon tetrachloride (CC14). Then, in order to avoid CC14 poisoning, it is decided to add a layer of water to both arms of manometer (2nd situation). So, 4 cm of water is added to the left arm and 8 cm of water is added to right arm. In this new situation, what will be the height difference of manometer fluid (CC14) between the arms of the manometer (Rm,2)? Data: pbenzene=876 kg/m³, pwater=997 kg/m², pccCI4=1587 kg/m³ Benzene Flow Benzene Flow "wright=8cm Rm,1 Rm2 =4cm[ 1 st Situation: Before adding water to manometer's arms 2 nd Situation: After adding water to manometer's armsarrow_forwardQ2 (a) The differential mercury manometer of Figure 2(a) is connected to pipe X (through pi) containing kerosene (pk = 786 kg/m'), and to pipe Y (through p2) containing water (pw = 997 kg/m'). Determine the pressure difference, px-py, given that the density of mercury is 13600 kg/m. 50 cm Water p2 Kerosene 30 cm p1 40 cm Mercury to Y Figure 2(a) Differential Manometerarrow_forwardA manometer is an accurate pressure measuring device that is used to measure low pressure in the pipes. Select one: O True O False In a flow channel, the density of fluid at entry is equal to the density of fluid at exit for a compressible fluid. Select one: O True O False 10bar = 1MN/m2 Select one: O True O Falsearrow_forward
- A vertical U-tube partially filled with alcohol (SG= 0.99) is rotated at a specified rate about its left arm. Compute for the following: (a) angular velocity of the tube's rotation if the alcohol is on the brink of spilling (b) pressure at point B during the rotation of the tube Please provide explanation per line of solution. thanks 10 cm 20 cm B +12.5 cm - 12.5 cm 25 cmarrow_forwardIn the benzene plant, the pressure drop at some point of a pipeline in which benzene is passing through is measured with a U-tube manometer (Rm,1) as 10 cm (1stsituation). The manometer fluid is carbon tetrachloride(CCl4). Then, in order to avoid CCl4 poisoning, it is decided to add a layer of water to both arms of manometer (2nd situation). So, 4 cm of water is added to the left arm and 8 cm of water is added to right arm. In this newsituation, what will be the height difference of manometer fluid (CCl4) between the arms of the manometer (Rm,2)?Data: ρbenzene=876 kg/m3, ρwater=997 kg/m3, ρCCl4=1587 kg/m3arrow_forwardConsider a soap bubble of diameter 3 mm. If the surfacetension coeffi cient is 0.072 N/m and external pressureis 0 Pa gage, what is the bubble’s internal gage pressure?( a ) - 24 Pa, ( b ) + 48 Pa, ( c ) + 96 Pa, ( d ) + 192 Pa,( e ) -192 Paarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License