Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 43, Problem 8ASRQ
While discussing a pressure test: Technician A says that a pressure drop of more than 15 psi during a shift indicates a possible leak. Technician B says that any pressure drop between shifts indicates a problem. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Technician A says that if the oil pressure
shows low on the vehicle's gauge, engine
oil pressure should be verified using a
manual test gauge. Technician B says that
if a vehicle's oil pressure gauge reads too
high, engine oil pressure should be
verified using a manual test gauge. Who is
correct?
Select one:
a. Technician A
b. Technician B
c. Both A and B
d. Neither A nor B
A technician is inspecting a vehicle and finds
the upper radiator hose is collapsed, and the
cooling system pulled into a vacuum when
cold. Technician A states that a leak in the
surge tank could be the cause. Technician B
states that the radiator cap is most likely
defective. Who is correct?
Select one:
a. Technician A only
b. Technician B only
c. Both Technicians A and B
d. Neither Technician A nor B
When performing a coolant pressure test,
Technician A says to pressurize the system to
the pressure shown on the radiator cap.
Technician B says that the coolant should be
drained before performing the test. Who is
correct?
Select one:
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Chapter 43 Solutions
Automotive Technology
Ch. 43 - What is the most probable cause of a low fluid...Ch. 43 - What does milky colored ATF indicate?Ch. 43 - What do varnish or gum deposits on the dipstick...Ch. 43 - Typically during a pressure test, the pressure...Ch. 43 - List five reasons for replacing a torque...Ch. 43 - Explain why oil circuit diagrams are invaluable...Ch. 43 - Explain how a plugged fluid cooler can cause a...Ch. 43 - What is checked during a stall test?Ch. 43 - Ifa transmission does not have a dipstick, how do...Ch. 43 - What should you do if a valve does not move freely...
Ch. 43 - Which of the following is the most likely cause...Ch. 43 - When should the ATF level be checked on most...Ch. 43 - Pressure readings reveal possible problems in...Ch. 43 - Which of the following is a probable cause for a...Ch. 43 - When rebuilding an automatic transmission, which...Ch. 43 - Technician A says that a prerequisite to accurate...Ch. 43 - While discussing proper band adjustment...Ch. 43 - Technician A says that if the shift for all...Ch. 43 - Technician A says that the only positive way to...Ch. 43 - Technician A says that delayed shifting can be...Ch. 43 - While checking the condition of a cars ATF:...Ch. 43 - While discussing the results of an oil pressure...Ch. 43 - While discussing a pressure test: Technician A...Ch. 43 - While checking the engine and transmission mounts...Ch. 43 - While discussing the cause of aerated fluid in a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Typically during a pressure test, the pressure should not drop more than_____ psi between shifts.arrow_forwardTechnician A says that coolant hoses should be squeezed to check for hardening or softening. Technician B says that coolant hoses should be visually inspected for swelling and cracks. Who is correct?arrow_forwardTRUE OR FALSE: The pressure variation from any point to another will be determined by applying Newton’s second law.arrow_forward
- Two technicians are discussing a coolant drain and refill. Technician A says that draining the coolant removes all coolant from the system. Technician B says that any trapped air in the system will bleed itself out automatically. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that it takes about 1 pint of oil to raise the oil level from "add" to "full." Technician B says that it takes about 1 quart to raise it that much. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward2.A. You can usually check for a leak in a vacuum system by looking at or feelingA. at the exhaust of the vacuum pump.B. at the vacuum gauge at the vacuum pump.C. for signs of dirt on the piping. 2.B. When you measure the voltage drop across a set of contacts, you'reA. checking the quality of the contact set.B. sensing how much current is flowing in the circuit.C. measuring the equivalent motor resistance. 2.C. A chain-drive system can be aligned easier than a belt-drive system since the chain-drive systemA. can have a string left on the sprockets after the alignment is complete.B. can have the chain removed while the final alignment is taking place.C. is less critical to misalignment.arrow_forward
- 4.a. You can usually check for a leak in a vacuum system by looking at or feelingA. at the vacuum gauge at the vacuum pump.B. for signs of dirt on the piping.C. at the exhaust of the vacuum pump. 4.b. When a pneumatic solenoid fails, the failure is normally due to aB. weak pilot.C. bad spool.D. ripped seal.arrow_forwardTwo techs are discussing oil coolers. Technician A says that when inspecting oil- to-water type coolers, look for mixing of the fluids: oil in the coolant, and coolant in the oil. Technician B says that when inspecting oil-to-air type coolers, look for oil in the coolant only. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that when installing an oil filter, you should tighten it with a filter wrench to prevent it from falling off. Technician B says that oil filters should only be installed by hand. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- Coolant hoses are being discussed. Technician A states that many manufacturers recommend coolant hose replacement on a maintenance schedule. Technician B states that coolant hoses can fail prematurely due to contamination by oil. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forwardTechnician A says that the same hydrometer can be used for both ethylene glycol and propylene glycol coolants. Technician B says that some hydrometers include a thermometer to compensate the reading based on coolant temperature. Who is correct? Select one: a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardCompressed air can be used to clean the machine, is a general safety precaution while working in a workshop. Select one: True O Falsearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Pressure Vessels Introduction; Author: Engineering and Design Solutions;https://www.youtube.com/watch?v=Z1J97IpFc2k;License: Standard youtube license