Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 43, Problem 2ASRQ
While discussing proper band adjustment procedures: Technician A says that on some vehicles the bands can be adjusted externally with a torque wrench. Technician B says that a calibrated inch- pound torque wrench is normally used to tighten the band adjusting bolt to a specified torque. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Technician A says that broken or worn engine and transaxle mounts can cause a transaxie to have shiftinf problems.Technician B says that poor shift boot alignment can cause a transaxle to jump out of gear.Who is correct?
a.Technician A only
b.Technician B only
c. both A and B
d. Neither A or nor B.
From the following identify a true statement regarding the adjustment of drive belt tension.
a.
Less than 8 mm should be the correct a deflection for each belt which is under tension
b.
More than 6 mm should be the correct a deflection for each belt which is under tension
c.
More than 8 mm should be the correct a deflection for each belt which is under tension.
d.
More than 6 mm and less than 8 mm should be the correct a deflection for each belt which is under tension.
when discussing shift problems, technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. technician b says that poor shift boot alignment can cause a transaxle to jump out of gear
Chapter 43 Solutions
Automotive Technology
Ch. 43 - What is the most probable cause of a low fluid...Ch. 43 - What does milky colored ATF indicate?Ch. 43 - What do varnish or gum deposits on the dipstick...Ch. 43 - Typically during a pressure test, the pressure...Ch. 43 - List five reasons for replacing a torque...Ch. 43 - Explain why oil circuit diagrams are invaluable...Ch. 43 - Explain how a plugged fluid cooler can cause a...Ch. 43 - What is checked during a stall test?Ch. 43 - Ifa transmission does not have a dipstick, how do...Ch. 43 - What should you do if a valve does not move freely...
Ch. 43 - Which of the following is the most likely cause...Ch. 43 - When should the ATF level be checked on most...Ch. 43 - Pressure readings reveal possible problems in...Ch. 43 - Which of the following is a probable cause for a...Ch. 43 - When rebuilding an automatic transmission, which...Ch. 43 - Technician A says that a prerequisite to accurate...Ch. 43 - While discussing proper band adjustment...Ch. 43 - Technician A says that if the shift for all...Ch. 43 - Technician A says that the only positive way to...Ch. 43 - Technician A says that delayed shifting can be...Ch. 43 - While checking the condition of a cars ATF:...Ch. 43 - While discussing the results of an oil pressure...Ch. 43 - While discussing a pressure test: Technician A...Ch. 43 - While checking the engine and transmission mounts...Ch. 43 - While discussing the cause of aerated fluid in a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that some small cracks in the accessory drive belt may be within tolerance. Technician B says that serpentine belts can be checked with a wear gauge. Who is correct? Select one: a. Technician A only b. Technician B only C. Both A and B d. Neither A nor Barrow_forwardWhen discussing the possible causes for a shudder during acceleration, Technician A says that a worn inner CV joint could be the cause. Technician B says that insufficient differential gear backlash could be the cause of the problem. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forwardWhich of the following is the most likely cause for a shudder during the engagement of a lock-up torque converter? a. A bad converter b. Worn or damaged CV or U-joints c. A worn front planetary gearset d. Loose flexplatearrow_forward
- Pinion gear-to-flywheel ring gear clearance is beingdiscussed: Technician A says that if there is too muchclearance, there will be a high pitch while the enginecranks. Technician B says that if there is too littleclearance, there will be a high pitch noise after theengine is started. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor Barrow_forwardWhile inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?arrow_forwardTechnician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct? a. A only b. B only c. both A and B d. neither A nor B If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches? a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct? a. A only b. B only c. both A and B d. neither A nor B Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation. a. True b. Falsearrow_forward
- Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct? a. A only b. B only c. both A and B d. neither A nor B If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches? a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct? a. A only b. B only c. both A and B d. neither A nor B Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation. a. True b. False Rusted-through brake lines are uncommon. a. True b. False A technician is diagnosing a vehicle with…arrow_forwardWhen reviewing the procedure for replacing an axle boot, Technician A says that the position of the old boot should be marked on the shaft before removing it. Technician B says that if the boot is dimpled or collapsed after the new boot is installed, a dulled screwdriver should be used to allow air to enter the boot. Who is correct? O a. A only O b. B only O c. Both A and B O d. Neither A nor Barrow_forwardWhen examining disc brakes: Technician A visually inspects the rotor and says that the rotor can be reused if it is not damaged or scored. Technician B says that it is normal for the inboard pad to be slightly more worn than the outside pad. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- Technician A says that fixed calipers use a piston oneach side of the rotor to apply the brakes. Technician Bsays that sliding calipers typically use only one pistonor pistons on one side of the rotor. Who is correct?a. Technician A onlyb. Technician B onlyc. Both A and Bd. Neither A nor Barrow_forwardA vehicle makes a loud clicking sound during a left turn; during a right turn, the clicking noise is still apparent but is less pronounced. Technician A says that the left inner CV joint may be the source of the noise. Technician B says that the left outer CV joint may be causing the noise. Who is correct? O a. A only Ob.B only O c. Both A and B O d. Neither A nor Barrow_forwardTechnician A says that side-bearing preload limits the amount the differential case is able to move laterally in the axle housing. Technician B says that adjusting backlash sets the depths of the mesh between the ring and pinion gears’ teeth. Who is correct?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Hand Tools; Author: UCI Media;https://www.youtube.com/watch?v=4o0tqF0jDdo;License: Standard Youtube License