Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 43, Problem 5MC
When rebuilding an automatic transmission, which of the following is not true?
a. All pumps, valve bodies, and cases should be checked for warpage and should be flat filed to take off any high spots or burrs prior to reassembly.
b. Only use lint-free rags to wipe parts off.
c. Lubricate all thrust washers, bearings, and bush ings before installing them.
d. Soak all friction materials in clean engine oil prior to installing them.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Which of the following ensures proper timing of the intake and exhaust valve events?
The length of the tappets relative to the pushrods.
Proper pairing of the gear set joining the crankshaft to the camshaft.
The pulse timer mounted in series with the piston.
The installation of the flywheel key.
True or False? The camshaft is always locatedin the engine block.
Technician A says check balls are often used to block holes between the transmission valve body and the spacer plate. Technician B says spacer plates may be installed between the transmission valve body and case. Who is right?
Chapter 43 Solutions
Automotive Technology
Ch. 43 - What is the most probable cause of a low fluid...Ch. 43 - What does milky colored ATF indicate?Ch. 43 - What do varnish or gum deposits on the dipstick...Ch. 43 - Typically during a pressure test, the pressure...Ch. 43 - List five reasons for replacing a torque...Ch. 43 - Explain why oil circuit diagrams are invaluable...Ch. 43 - Explain how a plugged fluid cooler can cause a...Ch. 43 - What is checked during a stall test?Ch. 43 - Ifa transmission does not have a dipstick, how do...Ch. 43 - What should you do if a valve does not move freely...
Ch. 43 - Which of the following is the most likely cause...Ch. 43 - When should the ATF level be checked on most...Ch. 43 - Pressure readings reveal possible problems in...Ch. 43 - Which of the following is a probable cause for a...Ch. 43 - When rebuilding an automatic transmission, which...Ch. 43 - Technician A says that a prerequisite to accurate...Ch. 43 - While discussing proper band adjustment...Ch. 43 - Technician A says that if the shift for all...Ch. 43 - Technician A says that the only positive way to...Ch. 43 - Technician A says that delayed shifting can be...Ch. 43 - While checking the condition of a cars ATF:...Ch. 43 - While discussing the results of an oil pressure...Ch. 43 - While discussing a pressure test: Technician A...Ch. 43 - While checking the engine and transmission mounts...Ch. 43 - While discussing the cause of aerated fluid in a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- When servicing transfer cases, all of the following are correct, except_____. a. it must be supported on a transmission jack or safety stands b. the chain drive and a planetary gearset must be adjusted to specifications c. visual inspections for leaks and damage are necessary d. follow the manufacturers recommendations for lubricantsarrow_forwardTechnician A says that the proper fluid level for a manual transmission is normally to the bottom of the filler hole. Technician B says that low lubricant levels can cause a standard transmission to clash during shifting. Who is correct?arrow_forwardTrue or False? The camshaft is always located in the engine block.arrow_forward
- What is the importance of aligning the notches found on the cam-gear and crank-gear? (Select the best answer) Open and close the intake/exhaust valves Increase engine efficiency Ensure proper engine timing None of these answers are correctarrow_forwardlist five checks that should be made during the visual inspection of the parts of a transmission/transaxle.arrow_forwardWhat provisions are usually included on tractor engines to aid in the correct timing of the camshaft?arrow_forward
- 128) Technician A says slide hammer pullers are usually required to remove the front pump from the transmission housing. Technician B says a special tool is available to remove the front pump on some transmissions. Which technician is correct? O Technician A Technician B O Both technicians A and B Neither technician A nor Barrow_forwardWhy is it important to loosen the cylinder head bolts in the recommended order?arrow_forwardBefore installing the crankshaft, what should you spray onto the bearings?arrow_forward
- Technician A says that rotary oil flow is the oil flow around the circumference of the torque convertercaused by the rotation of the torque converter on its axis. Technician B says that the centrifugal lockup clutch is the type installed in most automatic transmissions. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardA vehicle has had several radiator replacements, and each time there has been pinhole leaks in the aluminum. Technician A states that the engine coolant may need to be exchanged more often. Technician B states that the engine grounds should be inspected closely since this could be the cause. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forwardWhich of the following statements about drum brakeshoes is not true?a. Web thickness varies only with changes in shoesize.b. Many shoes have indented places along the edgeof the rim.c. The shoe rim is welded to the web.d. The primary/leading shoe is typically the one thatis positioned toward the front of the vehiclearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License