Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 40, Problem 10MC
Which of the following describes the double-Cardan universal joint?
a. It is most often installed in front-engine rear- wheel-drive luxury automobiles.
b. It is classified as a constant velocity U-joint.
c. A centering ball socket is inside the coupling yoke between the two universal joints.
d. All of the above.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Large cars with long drive shafts often use a double-U-joint arrangement called a __ .a. Spicer style U-jointb. constant velocity U-jointc. Cleveland style U-jointd. none of the above
only use revolute joints
*
Universal joint is used for
non parallel shafts whose axes are O
coplanar.
connecting radiator hoses. O
engaging the engine with the
transmission system.
O O
checking the fuel level. O
increasing the engine torque. O
Chapter 40 Solutions
Automotive Technology
Ch. 40 - Prob. 1SACh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In front-wheel drivetrains, the CV joint nearer the transaxle is the____. a. inner joint b. inboard joint c. outboard joint d. both a and barrow_forwardQ2.Types of Shaft Coupling. Q3.Explain Design of Muff Coupling.arrow_forwardWhich of the following CV joint tests should be performed to determine if the CV joint needs to be serviced? a. balance test b. chassis test c. squeeze test d. spin testarrow_forward
- Define the following,Joint.Link.Joint space.Actuator space.arrow_forwardThe CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the right side of the vehicle appear to be stretched apart. Technician A says that one or more of the engine/transaxle's mounts may be broken. Technician B says that one or more of the engine/transaxle's subframe mounts may be broken. Who is correct? O a. A only O b.B only C. Both A and B O d. Neither A nor Barrow_forwardA constant velocity joint that is capable of in-and-out movement is a: Select one: a. both fixed joint and inboard joint b. inboard joint c. fixed joint d. plunge jointarrow_forward
- Which of the following is part of the sprung weight ofa vehicle?a. Steering linkageb. Tiresc. Engined. All of the abovearrow_forwardLarge cars with long drive shafts often use a double U-joint arrangement called a_____. a. Spicer style U-joint b. constant velocity U-joint c. Cleveland style U-joint d. none of the abovearrow_forwardNumber of half joints (J2)?arrow_forward
- ExaniI Which of the following is not considered as a lower pair Revolute pair Prismatic pair O Roller Slider A special case of the four bar linkage where the driven crank were made of infinite length Grashof mechanism Drag link mechanism Quick return mechanism Slider crank mechanismarrow_forwardWhich type of driving axle supports the weightof the vehicle?a. Semifloatingb. Three-quarter floatingc. Full-floatingd. None of the abovearrow_forwardWhen reviewing the service procedures for CV joints and drive axles, Technician A says that the axle can be used as a slide hammer to help remove a stubborn inboard joint from the transaxle. Technician B says that a drive axle should never be allowed to hang by its own weight during removal or installation. Who is correct? O a. A only Ob.B only O c. Both A and B O d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License