Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 40, Problem 6ASRQ
While diagnosing the cause of a clicking noise that is heard only when the car is turning: Technician A says that the most probable cause is a worn wheel bearing. Technician B says that the most probable cause is a worn outboard CV joint. Who is correct?
a. Technician A only
b. Technician B only
c. Both A and B
d. Neither A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
When reviewing the procedure for replacing an axle boot,
Technician A says that the position of the old boot should be marked on the shaft before removing it.
Technician B says that if the boot is dimpled or collapsed after the new boot is installed, a dulled screwdriver should be used to allow air to enter the boot.
Who is correct?
O a. A only
O b. B only
O c. Both A and B
O d. Neither A nor B
When discussing the possible causes for a shudder during acceleration,
Technician A says that a worn inner CV joint could be the cause.
Technician B says that insufficient differential gear backlash could be the cause of the problem.
Who is correct?
O a. A only
O b. B only
O c. Both A and B
O d. Neither A nor B
A vehicle makes a loud clicking sound during a left turn; during a right turn, the clicking noise is still apparent but is less pronounced.
Technician A says that the left inner CV joint may be the source of the noise.
Technician B says that the left outer CV joint may be causing the noise.
Who is correct?
O a. A only
Ob.B only
O c. Both A and B
O d. Neither A nor B
Chapter 40 Solutions
Automotive Technology
Ch. 40 - Prob. 1SACh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct? a. A only b. B only c. both A and B d. neither A nor B If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches? a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct? a. A only b. B only c. both A and B d. neither A nor B Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation. a. True b. Falsearrow_forwardTechnician A says the size of the pads, shoes, drums, and rotors is based on the weight of the vehicle. Technician B says their size is based on the top speed the vehicle can achieve. Who is correct? a. A only b. B only c. both A and B d. neither A nor B If a force of 150 pounds is applied to a master cylinder with a piston area of 1 square inch, how much force is developed on a wheel cylinder that has a piston area of 2 square inches? a. 75 pounds b. 150 pounds c. 300 pounds d. 450 pounds While manually bleeding a brake system, Technician A loosens all the brake bleeder screws at the same time. Technician B uses shop air to push the fluid and air through the lines and out the bleeder screws. Who is correct? a. A only b. B only c. both A and B d. neither A nor B Brake fluid serves as a lubricant for the parts of the hydraulic system and ensures smooth and even operation. a. True b. False Rusted-through brake lines are uncommon. a. True b. False A technician is diagnosing a vehicle with…arrow_forwardwhen discussing shift problems, technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. technician b says that poor shift boot alignment can cause a transaxle to jump out of geararrow_forward
- When examining disc brakes: Technician A visually inspects the rotor and says that the rotor can be reused if it is not damaged or scored. Technician B says that it is normal for the inboard pad to be slightly more worn than the outside pad. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhen discussing shift problems, Technician A says that worn or broken engine and transaxle mounts can cause a transaxle to have shifting problems. Technician B that poor shift boot alignment can cause a transaxle to jump out of gear. says Who is correct? A. A only C. Both A and B B. B only D. Neither A nor Barrow_forwardvehicle is producing a sharp, metallic rappingsound originating in the upper portion of the engine.It is most noticeable during idle. Technician A diagnosesthe problem as piston pin knock. Technician Bsays that the problem is most likely a loose crankshaftthrust bearing. Who is correct?a. Technician Ab. Technician Bc. Both A and Bd. Neither A nor Barrow_forward
- Technician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?arrow_forwardWhen replacing brake pads on a vehicle: Tech-nician A works on one wheel before beginning work on another. Technician B uses a minimum of 52 psi of air pressure to force the piston from the caliper housing. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhile diagnosing the problems that can be caused by worn tie-rod ends: Technician A says that they can cause scalloped and scuffed tires. Technician B says that they can cause the vehicle to pull to one side. Who is correct?arrow_forward
- A discussion concerning CV joint testing is being held. Technician A says that a recommended method to check CV joints is to raise the vehícle so that the lower control arms are hanging freely; at this point the engine can be accelerated while noise checks can be performed. Technician B says that the vehicle should be road tested so that the CV joints can be checked under load. Who is correct? O a. A only O b. B only c. Both A and B d. Neither A nor Barrow_forwardWhich of the following is part of the sprung weight ofa vehicle?a. Steering linkageb. Tiresc. Engined. All of the abovearrow_forwardTechnician A says that a malfunction of the ABS causes the control module to shut off or inhibit the system. Technician B says that a loss of hydraulic fluid or power booster pressure disables the antilock brake system. Who is correct? a. Technician A only b.Technician B only c.Both A and B d.Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License