Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 40, Problem 13RQ
Large cars with long drive shafts often use a double U-joint arrangement called a_____.
a. Spicer style U-joint
b. constant velocity U-joint
c. Cleveland style U-joint
d. none of the above
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
only use revolute joints
*
Universal joint is used for
non parallel shafts whose axes are O
coplanar.
connecting radiator hoses. O
engaging the engine with the
transmission system.
O O
checking the fuel level. O
increasing the engine torque. O
Q2.Types of Shaft Coupling.
Q3.Explain Design of Muff Coupling.
Chapter 40 Solutions
Automotive Technology: A Systems Approach (MindTap Course List)
Ch. 40 - Prob. 1RQCh. 40 - What type of axle housing resembles a banjo?Ch. 40 - What type of axle merely supports the vehicle load...Ch. 40 - What type of floating axle has one wheel bearing...Ch. 40 - How are problems normally first noticed with the...Ch. 40 - In front-wheel drivetrains, the CV joint nearer...Ch. 40 - A CV joint that is capable of in-and-out movement...Ch. 40 - The double-offset joint is typically used in...Ch. 40 - Which type of joint has a flatter design than any...Ch. 40 - Which of these is the best way to determine which...
Ch. 40 - The single Cardan/Spicer universal joint is also...Ch. 40 - The drive shaft component that provides a means of...Ch. 40 - Large cars with long drive shafts often use a...Ch. 40 - Which type of driving axle supports the weight of...Ch. 40 - Which of the following describes the double-Cardan...Ch. 40 - Technician A says that a gear tooth pattern...Ch. 40 - Technician A says that limited-slip differential...Ch. 40 - Technician A says that side-bearing preload limits...Ch. 40 - Technician A says that a hunting gearset is one in...Ch. 40 - While discussing the possible causes for a...Ch. 40 - While diagnosing the cause of a clicking noise...Ch. 40 - Prob. 7ASRQCh. 40 - Technician A says that when a car is moving...Ch. 40 - While discussing different types of ring and...Ch. 40 - While reviewing the procedure for setting...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In front-wheel drivetrains, the CV joint nearer the transaxle is the____. a. inner joint b. inboard joint c. outboard joint d. both a and barrow_forwardCan be manufactured by cast aluminum alloy only. a. Nose Section b. Power Section c. Supercharger section d. Accessory Section e. All of the above The rollers and balls used in some bearings are made of polished steel. a. True b. Falsearrow_forwardA ball and a socket joint forms aarrow_forward
- 17 - Which of the following statements about supports is false?A) Bearings can be in the form of sliding, fixed, built-in and intermediate joints. B) There is only freedom of rotation in the intermediate joint.C) There is no freedom of movement in the fixed joint.D) There is freedom of movement in the x-axis in the sliding joint and rotational freedom at the joint point. E) There is no freedom of movement in the built-in support.arrow_forward35 - Which of the following statements about supports is false?A) There is no freedom of movement in the fixed joint.B) There is no freedom of movement in the built-in support. C) There is only freedom of rotation in the intermediate joint.D) Bearings can be in the form of sliding, fixed, built-in and intermediate joints. E) There is freedom of movement in the x-axis in the sliding joint and rotational freedom at the joint point.arrow_forward1) The working face of ordinary flat key is 1 A. Side C. Bottom surface D. End face B. Upper top surface 2)When the rotating shaft works, it mainly bears_ A. Pure torque C. Torque and bending moment .B. Pure bending moment D. Friction torque 3) Section angle of V-belt in belt drive q-40°,In order to make good contact and increase friction, the pulley groove angle should be A.Slightly greater than 40° C.Equal to 40 B.Slightly less than 40" .D.Equal to 90°arrow_forward
- option e and f plzarrow_forwardWords: Cage, Centre, Changes, Drive, Flange, Inner, Joint, Race, PropellerA Löbro constant-velocity __________________, has an outer race, an inner race and a __________________ with steel balls.The outer race is bolted to the __________________ of the front propeller shaft, and the inner race is splined to the front endof the rear __________________ shaft. The joint is enclosed by a dust shield and boot. The front shaft is supported by a__________________ bearing.This type of joint is designed to allow __________________ in propeller shaft angle and also changes in propeller shaft length.Both the __________________ race and the outer race have angular grooves for the balls. The balls transfer__________________ from one race to the other but, at the same time, the inner __________________ is able to move in orout in the grooves or change its angle.arrow_forwardThe output shaft of a reducer is bearing in bearings A and B. From deep groove ball bearings, bed A is fixed and bed B is free-formed. Which of the following is true for the inner and Outer Ring of the bearing in bearing B?Please select one: a. Because the FG force acts on the shaft, there are no forces coming to the bracelets.b. the inner ring has a point, and the Outer Ring has an environmental load.c. Environmental load affects the outer ring.d. environmental load acts on the inner ring and point load acts on the outer ring.e. both environmental and point load affect the inner ring.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Power Transmission; Author: Terry Brown Mechanical Engineering;https://www.youtube.com/watch?v=YVm4LNVp1vA;License: Standard Youtube License