Theory and Design for Mechanical Measurements
6th Edition
ISBN: 9781118881279
Author: Richard S. Figliola, Donald E. Beasley
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 4, Problem 4.17P
From 19 measurements of a pressure controller, the mean operating pressure is 4.97 kPa with a standard deviation of 0.0461 kPa. Neglecting other sources or error, state the true mean pressure at 95% confidence.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
The actual value of pressure differential for flow across a venturimeter is 60 mm WC. The measured values using a pressure sensor are; Confidence level 95% mm WC 59.8,59.2,59.7,60.2,60.3,60.1,60.5
Estimate
Bias uncertainty (1)
Precision uncertainty (2)
Total uncertainty (3)
At a fixed operating setting, the pressure in a line downstream of a reciprocating compressor has a mean value of 12.0 bar with a standard deviation of 1.0 bar based on a very large data set obtained from continuous monitoring. What is the probability that the line pressure will exceed 13.0 bar during any measurement?
A transducer's certificate of calibration (excerpt below) identifies two instrument errors with
uncertainties at 95% confidence over it range.
Resolution
Range
Linearity error
Hysteresis error
0.25 N
0 to 200 N
Within 0.2 N over
range
Within 0.3 N over
range
1. Estimate the instrument design-stage uncertainty.
2. What is the instrument standard uncertainty?
Chapter 4 Solutions
Theory and Design for Mechanical Measurements
Ch. 4 - Prob. 4.1PCh. 4 - Prob. 4.2PCh. 4 - At a fixed operating setting, the pressure in a...Ch. 4 - Consider the toss of four coins. There are 24...Ch. 4 - As a game, slide a matchbook across a table,...Ch. 4 - Prob. 4.6PCh. 4 - A student conducts a lab exercise to calculate the...Ch. 4 - From a large database, the Highway Patrol...Ch. 4 - Prob. 4.9PCh. 4 - Prob. 4.10P
Ch. 4 - Prob. 4.11PCh. 4 - Prob. 4.12PCh. 4 - Prob. 4.13PCh. 4 - Prob. 4.14PCh. 4 - Prob. 4.15PCh. 4 - From 19 measurements of a pressure controller, the...Ch. 4 - From 19 measurements of a pressure controller, the...Ch. 4 - When the parameters of a population are known, the...Ch. 4 - A professor grades students on a normal curve. For...Ch. 4 - Prob. 4.20PCh. 4 - 4.21 An automotive manufacturer removes the...Ch. 4 - Prob. 4.22PCh. 4 - Prob. 4.23PCh. 4 - A sampling of 409 motor shafts from a very large...Ch. 4 - During the course of a motor test, the motor rpm...Ch. 4 - A baich of rivets is tested for shear strength. A...Ch. 4 - Three independent sets of data are collected front...Ch. 4 - Prob. 4.28PCh. 4 - 4.29 An engineer measures the diameter of 20 tubes...Ch. 4 - Prob. 4.30PCh. 4 - For Problems 4.30 through 4.36. itwould be helpful...Ch. 4 - For Problems 4.30 through 4.36. itwould be helpful...Ch. 4 - For Problems 4.30 through 4.36. itwould be helpful...Ch. 4 - Prob. 4.34PCh. 4 - Prob. 4.35PCh. 4 - Prob. 4.36PCh. 4 - A manufacturer of general aircraft dry vacuum...Ch. 4 - Strength tests made on a batch of cold-drawn steel...Ch. 4 - 4.39 Determine the one-sided 95 th-percentile of...Ch. 4 - 4.40 The manufacturer of an electrical fuse claims...Ch. 4 - How many independent random measurements of a...Ch. 4 - Based on 51 measurements of a time-dependent...Ch. 4 - 4.43 Estimate the probability with which an...Ch. 4 - Prob. 4.44PCh. 4 - Prob. 4.45PCh. 4 - Prob. 4.46PCh. 4 - Prob. 4.47PCh. 4 - 4.48 A cantilever is loaded at its tip. Tip...Ch. 4 - Prob. 4.49PCh. 4 - Prob. 4.50PCh. 4 - A transducer is used to indicate the pressure of a...Ch. 4 - An engineer takes water samples from 15 lakes in...Ch. 4 - A random sample of 51 aircraft rivets is taken...Ch. 4 - Prob. 4.54PCh. 4 - Estimate the p-value for N = 16. t = 1.798...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A temperature measurement system has the following specifications: -128 to 781°C Range Linearity error 0.29% FSO Hysteresis error 0.12% FSO Sensitivity error 0.04% FSO Zero drift 0.32% FSO FSO stands for "Full Scale Output". Estimate the overall instrument uncertainty for this system based on the available information. Use the maximum possible output range over the FSO in your computations.arrow_forward2. An electrical firm manufactures light bulbs that have a lifetime that is approximately normally distributed with a standard deviation of 36 hours. A lifetime test of n=36 samples resulted in the sample average of 1510 hours. Assume the significance level of 0.05. (a) Test the hypothesis Ho: µ = 1000 versus H1: µ# 1000 using a p-value. (b) Test the hypothesis using critical region(s) approach. (c) Suppose that the true mean lifetime is 1510 hours. What is type Il error probability for this| two-sided test.arrow_forwardcompute the 95 confidence intervals for the inventory of a series of 12 replication of the simulation of a system, where the VERAGE INVENtory is 1000 units and sample standard deviation is 38arrow_forward
- 3. A consumer product company is formulating a new shampoo and is interested in foam height (in millimeters). Foam height is approximately normally distributed and has a standard deviation, 6, of 10 millimeters. The company wishes to test the following hypotheses using the results of n=25 samples: Ho: μ = 160, Ηi: μ < 160 The critical region to reject the null hypothesis is X < 155 %3D (a) Find the type I error probability a. (b) Find the probability of type II error if the true mean form height is 159 millimeters.arrow_forwardFor a site, if the load is 4,700,000 kWh, how many turbines is required if the specifications of the turbine is as follow: Rotor diameter = 60 m Cut in wind speed = 3 m/s Rated wind speed = 12 m/s Cut out wind speed = 20 m/s The mean wind speed = 6 m/s The standard deviation = 1.3 Also determine: the capacity factor, the availability factor, the load duration and the area required.arrow_forwardAn electrical firm manufactures light bulbs that have a lifetime that is approximately normally distributed with a standard deviation of 36 hours. A lifetime test of n=36 samples resulted in the sample average of 1510 hours. Assume the significance level of 0.05. (a) Test the hypothesis HO:µ=1500 versus H1:µ#1500using ap-value. (10pts) (b) Calculate the power of the test if the true mean lifetime is 1510. (10pts)arrow_forward
- Six standard deviations of a normally distributed process use 85% of the specification band. It is centered at the nominal dimension, located halfway between the upper and lower specification limits. Estimate C, and C₂. Interpret these ratios.arrow_forwardSectio A. The following are the weights in pounds of 10 pieces of balikbayan luggage: No. 3. 4 8. 9. 10 Wt. 124 125 125 123 124 127 125 126 121 120 Find the following measurements (two-decimal places): 4. Median: 1. Mean: 2. Sample standard deviation: 3. Range: 5. Mode:arrow_forwardQ.46 Robot Ltd. wishes to maintain enough safety stock during the lead time period between starting a new production run and its completion such that the probability of satisfying the customer demand during the lead time period is 95%. The lead time period is 5 days and daily customer demand can be assumed to follow the Gaussian (normal) distribution with mean 50 units and a standard deviation of 10 units. Using o-(0.95) = 1.64, where o represents the cumulative distribution function of the standard normal random variable, the amount of safety stock that must be maintained by Robot Ltd. to achieve this demand fulfilment probability for the lead time period is units. [Round off to two decimal places]arrow_forward
- A force measurement system (weight scale) has the following specifications as shown in Table 1: Estimate the overall instrument uncertainty for this system based on available information. FSO refers to full-scale operating range.arrow_forwardBolts installed on a production line are tightened with automatic wrenches. They are to be tightened sufficiently to yield the full cross-section in order to produce the highest possible initial tension. The limiting condition is twisting off the bolt head during assembly. The bolts have a mean twisting off torque of 20 Nm with a standard deviation of 1 Nm. The automatic wrenches have a standard deviation of 1.5Nm. What mean value of torque wrench setting would result in only 1 in 500 twisting off during assembly? Give a rough estimate only. A unit has a constant failure rate of 0.3% per 1000 hours. What is its MTBF? What are the probabilities of the unit successfully completing missions of 10000, 100000 and 1000000 hours? Give a rough estimate only.arrow_forwardA small sample (N = 7) of the static coefficient of friction (µ) between two materials is measured with the following data set: 0.0043 0.0050 0.0053 0.0047 0.0031 0.0051 0.0049 Test the data for outliers. Determine the mean value and its confidence.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
What is Metrology in Mechanical Engineering? | Terminologies & Measurement; Author: GaugeHow;https://www.youtube.com/watch?v=_KhMhFRehy8;License: Standard YouTube License, CC-BY