(a)
The heat flux for each radiator material.
Answer to Problem 4.11P
The heat flux for the brass radiator is
Explanation of Solution
Given:
The thickness of each radiator is
The temperature of engine fluid is
The ambient air temperature is
Formula used:
The expression heat flux of radiator is given by,
Here,
The temperature gradient is given by,
Here,
Substitute
Calculation:
The heat flux of aluminum radiator is calculated as,
Substitute
Here,
The heat flux of brass radiator is calculated as,
Substitute
Here,
Conclusion:
Therefore, the heat flux for the brass radiator is
(b)
The estimate of relative area and the relative weight of changing from brass radiator to an aluminum radiator.
Answer to Problem 4.11P
The relative area of aluminum is
Explanation of Solution
Given:
The heat transfer rate is the same for brass and aluminum.
The brass is
The density of brass is
Formula used:
The relation for rate of heat transfer in aluminum is given by,
Here,
The relation for rate of heat transfer in brass is given by,
Here,
The heat transfer rate is same for brass and aluminum.
Equate equation (IV) and (V) to obtain expression for
The expression for weight is given by,
Here,
Calculation:
The area of aluminum is calculated as,
Substitute
The wall of thickness of both the radiators is same.
Here,
The weight of brass is calculated as,
Substitute
Here,
The weight of aluminum is calculated as,
Substitute
Here,
Substitute
Divide equation (X) by (VIII).
Conclusion:
Therefore, the relative area of aluminum is
Want to see more full solutions like this?
Chapter 4 Solutions
Materials Science and Engineering Properties, SI Edition
- An aluminum pipe has a length of 68 m at a temperature of 15°C. An adjacent steel pipe at the same temperature is 10 mm longer. At what temperature will the aluminum pipe be 30 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5×106/°C and that the coefficient of thermal expansion for the steel is 12.5x10-6/°C. Answer: °℃arrow_forwardAn aluminum pipe with a length of 60 m at a temperature of 10°C rests freely on the ground. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. (a) At what temperature (degrees Celsius) will the aluminum pipe be 15 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are ca=23x10-6/°C and as=12x10-6/°C, respectively.) (b) What is the axial stress developed in the aluminum pipe when the temperature was increased? Aluminun Steel Figure No. 1 5 mmarrow_forward2. A Platinum resistance thermometer has a resistance of 100 ohms at 0°C and the value of alpha is 0.00385. In operation the resistance is 101 ohms. Calculate the temperature.arrow_forward
- An aluminum pipe has a length of 65 m at a temperature of 16°C. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. At what temperature (in degrees Celsius) will the aluminum pipe be 14 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are a, = 23 x 10-6/°C and a = 12 x 10-6/°C, respectively. Also assume that the temperature of both pipes change equally.) °Carrow_forwardQuestions: 2nd: Calculate the thermal resistance (R or R₂) of human skin with a thickness of 2 cm, per cm² of skin. ● thermal conductivity=0.627 N/(°C.s) ● • specific heat-c-3470 Nm/kg °C • density=1100 kg/m³ Rt - L KA where k is the materials conductivity [W.m³!.K-¹] L is the plane thickness [m] A is the plane area [m²]arrow_forwardWhiteware, porcelain, bricks and bio-ceramics are an example application derived from ceramic materials and undergoes thermal treatment. Briefly explain three (3) thermal treatment for ceramic materials.arrow_forward
- An aluminum calorimeter with a mass of 100 g contains 250 g of water. The calorimeter and water are in thermal equilibrium at 10.0°C. Two metallic blocks are placed into the water. One is a 50.0-g piece of copper at 80.0°C. The other has a mass of 70.0 g and is originally at a temperature of 100°C. The entire system stabilizes at a final temperature of 20.0°C. (a) Determine the specific heat of the unknown sample?arrow_forward3. A certain copper wire has a resistance of 25 ohms at 10°C. Take the temperature coefficient at 10°C to be 0.00409 deg/C. What must be the maximum operating temperature of the wire if its resistance is to increase by at most 20%?arrow_forwardAn aluminum pipe has a length of 60 m at a temperature of 10° C. An adjacent steel pipe at the same temperature is 5 mm longer than the aluminum pipe. At what temperature (degrees Celsius) will the aluminum pipe be 15 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are aAL=23x 10^-6°C and as=12x10^-6° C respectively)arrow_forward
- An aluminum pipe has a length of 75 m at a temperature of 18°C. An adjacent steel pipe at the same temperature is 0.005 m longer than the aluminum pipe. At what temperature (0C) will the aluminum pipe be 0.015 mm longer than the steel pipe? (Assume that the coefficients of thermal expansion of aluminum and steel are aa = 23 x 10–6/°C and as = 12 x 10–6/°C, respectively.)arrow_forwardAn aluminum pipe has a length of 52 m at a temperature of 6°C. An adjacent steel pipe at the same temperature is 8 mm longer. At what temperature will the aluminum pipe be 24 mm longer than the steel pipe? Assume that the coefficient of thermal expansion for the aluminum is 22.5x10-6/°C and that the coefficient of thermal expansion for the steel is 12.5×106/°C. Answer: °℃ Tf= iarrow_forwardWhich of the following is not a cause of energy loss in pipes? O Boundary friction O Changes in pipe diameter or geometry O The presence of control valves or fittings O Pipe temperaturearrow_forward
- Materials Science And Engineering PropertiesCivil EngineeringISBN:9781111988609Author:Charles GilmorePublisher:Cengage Learning