Fox and McDonald's Introduction to Fluid Mechanics
9th Edition
ISBN: 9781118912652
Author: Philip J. Pritchard, John W. Mitchell
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 4, Problem 145P
Transverse thrusters are used to make large ships fully maneuverable at low speeds without tugboat assistance. A transverse thruster consists of a propeller mounted in a duct; the unit is then mounted below the waterline in the bow or stern of the ship. The duct runs completely across the ship. Calculate the thrust developed by a 1865 kw unit (supplied to the propeller) if the duct is 2.8 m in diameter and the ship is stationary.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Air flows through a turbojet engine at the rate of 50.0 kg/s and the fuel flow rate is 1.0 kg/s. The exhaust gases leave the jet nozzle with a relative velocity of 600 m/s. Compute the velocity of the airplane, if the thrust power is 1.5 MW in the following two cases: 1. Pressure equilibrium exists ver the exit plane 2. If the pressure thrust is 8 kN
The air flow through a jet engine is 30 kg/s and the fuel flow is 1 kg/s. The exhaust gases leave with a relative velocity of 610 m/s. Pressure equilibrium exists over the exit plane. Compute the velocity of the airplane if the thrust power is 1.12 x 108 W.
Fans-2
5. The power output is 35 Hp to a centrifugal pump that is discharging 905
gpm and which operates at 1805 rpm against a head H= 125 ft, 220 V, 3
phase, 60 Hertz. If this pump is modified to operate 1205 rpm, assuming
its efficiency remains constant, determine its power input to the pump.
Chapter 4 Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Ch. 4 - An ice-cube tray containing 250 mL of freshwater...Ch. 4 - A hot air balloon with an initial volume of 2600...Ch. 4 - A fully loaded Boeing 777-200 jet transport...Ch. 4 - On the Milford Trek in New Zealand, there is a...Ch. 4 - A high school experiment consists of a block of...Ch. 4 - For a small particle of styrofoam (density = 19.2...Ch. 4 - Air at 20C and an absolute pressure of 101.3 kpa...Ch. 4 - A block of copper of mass 5 kg is heated to 90C...Ch. 4 - The average rate of heat loss from a person to the...Ch. 4 - The velocity field in the region shown is given by...
Ch. 4 - The area shown shaded is in a flow where the...Ch. 4 - Obtain an expression for the kinetic energy flux,...Ch. 4 - A 0.3 m by 0.5 m rectangular air duct carries a...Ch. 4 - Across a shock wave in a gas flow there is a great...Ch. 4 - Water flows in a pipeline composed of 75-mm and...Ch. 4 - The velocity distribution for laminar flow in a...Ch. 4 - A farmer is spraying a liquid through 10 nozzles,...Ch. 4 - A university laboratory that generates 15 m3/s of...Ch. 4 - Hydrogen is being pumped through a pipe system...Ch. 4 - Calculate the mean velocities for these...Ch. 4 - If the velocity profile in a passage of width 2R...Ch. 4 - Fluid with 1040 kg/m3 density is flowing steadily...Ch. 4 - A rice farmer needs to fill a 150 m 400 m field...Ch. 4 - In your kitchen, the sink is 60 cm by 45.7 cm. by...Ch. 4 - Fluid passes through this set of thin closely...Ch. 4 - A pipeline 0.3 m in diameter divides at a Y into...Ch. 4 - A manifold pipe of 3 in. diameter has four...Ch. 4 - You are trying to pump storm water out of your...Ch. 4 - In the incompressible flow through the device...Ch. 4 - Water enters a wide, flat channel of height 2h...Ch. 4 - Find the average efflux velocity V if the flow...Ch. 4 - Find V for this mushroom cap on a pipeline. P4.32Ch. 4 - Incompressible fluid flows steadily through a...Ch. 4 - A two-dimensional reducing bend has a linear...Ch. 4 - Water enters a two-dimensional, square channel of...Ch. 4 - Viscous liquid from a circular tank. D = 300 mm in...Ch. 4 - A rectangular tank used to supply water for a...Ch. 4 - A cylindrical tank, 0.3 m in diameter, drains...Ch. 4 - Air enters a tank through an area of 0.018 m2 with...Ch. 4 - A cylindrical tank, of diameter D = 50 mm, drains...Ch. 4 - A conical flask contains water to height H = 36.8...Ch. 4 - Water flows steadily past a porous flat plate....Ch. 4 - A tank of fixed volume contains brine with initial...Ch. 4 - A conical funnel of half-angle = 30 drains...Ch. 4 - Evaluate the net rate of flux of momentum out...Ch. 4 - Water flows steadily through a pipe of length L...Ch. 4 - Evaluate the net momentum flux through the bend of...Ch. 4 - Evaluate the net momentum flux through the channel...Ch. 4 - A conical enlargement in a vertical pipeline is 5...Ch. 4 - A 100-mm nozzle is bolted (with 6 bolts) to the...Ch. 4 - The projectile partially fills the end of the 0.3...Ch. 4 - Considering that in the fully developed region of...Ch. 4 - A jet of water issuing from a stationary nozzle at...Ch. 4 - A circular cylinder inserted across a stream of...Ch. 4 - A 6-in.-diameter horizontal pipeline bends through...Ch. 4 - The axes of the pipes are in a vertical plane. The...Ch. 4 - Water flows through a tee in a horizontal pipe...Ch. 4 - In a laboratory experiment, the water flow rate is...Ch. 4 - A gate is 1 m wide and 1.2 m tall and hinged at...Ch. 4 - Water flows steadily through a fire hose and...Ch. 4 - Two types of gasoline are blended by passing them...Ch. 4 - A circular cylinder inserted across a stream of...Ch. 4 - The pressure difference results from head loss...Ch. 4 - Obtain expressions for the rate of change in mass...Ch. 4 - Water is flowing steadily through the 180 elbow...Ch. 4 - Water flows steadily through the nozzle shown,...Ch. 4 - The pump, suction pipe, discharge pipe, and nozzle...Ch. 4 - The passage is 1.2 m wide normal to the paper....Ch. 4 - If the two-dimensional flow rate through this...Ch. 4 - Assume the bend of Problem 4.35 is a segment of a...Ch. 4 - A flat plate orifice of 50 mm diameter is located...Ch. 4 - At rated thrust, a liquid-fueled rocket motor...Ch. 4 - Flow from the end of a two-dimensional open...Ch. 4 - Calculate the magnitude and direction of the...Ch. 4 - This water jet of 50 mm diameter moving at 30 m/s...Ch. 4 - If the splitter is removed from the plate of...Ch. 4 - Consider flow through the sudden expansion shown....Ch. 4 - A conical spray head is shown. The fluid is water...Ch. 4 - A curved nozzle assembly that discharges to the...Ch. 4 - The pump maintains a pressure of 10 psi at the...Ch. 4 - A motorboat moves up a river at a speed of 9 m/s...Ch. 4 - A 30 reducing elbow is shown. The fluid is water....Ch. 4 - A monotube boiler consists of a 6 m length of...Ch. 4 - Water is discharged at a flow rate of 0.3m3/s from...Ch. 4 - A nozzle for a spray system is designed to produce...Ch. 4 - The horizontal velocity in the wake behind an...Ch. 4 - An incompressible fluid flows steadily in the...Ch. 4 - Consider the incompressible flow of fluid in a...Ch. 4 - Air at standard conditions flows along a flat...Ch. 4 - Gases leaving the propulsion nozzle of a rocket...Ch. 4 - Two large tanks containing water have small...Ch. 4 - Students are playing around with a water hose....Ch. 4 - A 2-kg disk is constrained horizontally but is...Ch. 4 - A stream of water from a 50-mm-diameter nozzle...Ch. 4 - A plane nozzle discharges vertically 1200 L/s per...Ch. 4 - In ancient Egypt, circular vessels filled with...Ch. 4 - Incompressible fluid of negligible viscosity is...Ch. 4 - The narrow gap between two closely spaced circular...Ch. 4 - Design a clepsydra (Egyptian water clock), which...Ch. 4 - Water from a stationary nozzle impinges on a...Ch. 4 - A freshwater jet boat takes in water through side...Ch. 4 - The Canadair CL-215T amphibious aircraft is...Ch. 4 - Water, in a 100-mm-diameter jet with speed of 30...Ch. 4 - Consider a series of turning vanes struck by a...Ch. 4 - A steady jet of water is used to propel a small...Ch. 4 - The cart of Problem 4.105 is accelerated by a jet...Ch. 4 - A vane/slider assembly moves under the influence...Ch. 4 - A cart is propelled by a liquid jet issuing...Ch. 4 - For the vane/slider problem of Problem 4.107, find...Ch. 4 - If the cart of Problem 4.105 is released at t = 0,...Ch. 4 - The wheeled cart shown rolls with negligible...Ch. 4 - A rocket sled is to be slowed from an initial...Ch. 4 - Starting from rest, the cart shown is propelled by...Ch. 4 - Solve Problem 4.107 if the vane and slider ride on...Ch. 4 - For the vane/slider problem of Problem 4.114, plot...Ch. 4 - A rectangular block of mass M, with vertical...Ch. 4 - A vertical jet of water impinges on a horizontal...Ch. 4 - A rocket sled traveling on a horizontal track is...Ch. 4 - A rocket sled accelerates from rest on a level...Ch. 4 - A rocket sled with initial mass of 900 kg is to be...Ch. 4 - A rocket sled with initial mass of 3 metric tons,...Ch. 4 - A home-made solid propellant rocket has an initial...Ch. 4 - Neglecting air resistance, what speed would a...Ch. 4 - The moving tank shown is to be slowed by lowering...Ch. 4 - The 90 reducing elbow of Example 4.6 discharges to...Ch. 4 - Crude oil (SG = 0:95) from a tanker dock flows...Ch. 4 - The simplified lawn sprinkler shown rotates in the...Ch. 4 - Calculate the torque about the pipes centerline in...Ch. 4 - A fire truck is equipped with a 66 ft long...Ch. 4 - Calculate the torque exerted on the flange joint...Ch. 4 - Consider the sprinkler of Problem 4.130 again....Ch. 4 - A small lawn sprinkler is shown. The sprinkler...Ch. 4 - When a garden hose is used to fill a bucket, water...Ch. 4 - A pipe branches symmetrically into two legs of...Ch. 4 - Compressed air is stored in a pressure bottle with...Ch. 4 - A turbine is supplied with 0.6 m3/s of water from...Ch. 4 - Air is drawn from the atmosphere into a...Ch. 4 - At high speeds the compressor and turbine of the...Ch. 4 - Transverse thrusters are used to make large ships...Ch. 4 - All major harbors are equipped with fire boats for...Ch. 4 - A pump draws water from a reservoir through a...Ch. 4 - Liquid flowing at high speed in a wide, horizontal...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Glycerin at 25 C flows through a straight hydraulic copper tube, 80 mm ODx2.8 mm wall, at a flow rate of 180 L/...
Applied Fluid Mechanics (7th Edition)
5.24 through 5.31 Calculate the forces in all members of the trusses shown, using the method of joints.
...
Applied Statics and Strength of Materials (6th Edition)
Which engineering field is primarily concerned with the planning, construction, and operation of facilities, su...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
In each case, the beam is subjected to the loadings shown. Draw the free-body diagram of the beam, and sketch t...
Mechanics of Materials
The cantilevered W530150 beam shown is subjected to an 8-kN force F applied by means of a welded plate at A. De...
Engineering Mechanics: Statics
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A 5-inch diameter centrifugal pump operating at 1000 RPM is geometrically similar to another 7.5 inch diameter pump when operating at 1400 RPM. The working fluid is water for both cases. Calculate the flow rate, head and brake power for the smaller pump if the flow rate, head and brake power for the largest diameter pump is 1000 gal/min, 50 ft and 15 hp respectively considering the point of operation previously described.arrow_forwardThe fluid flow rate was 1 m3 / s and the head was 10 m in the experiment performed at 2000 rpm with the 1/4 ratio model of a centrifugal pump designed to be used for oil. Calculate the power given by the pump to the fluid when the prototype pump operates at 1000 rpm. (ρsu = 1000 kg / m3, ρ oil = 800 kg / m3)arrow_forwardA Centrifugal pump discharges water with a volume flow rate of 110 liters per second. The inlet diameter D1 of the impeller is 150 mm, the blade thickness at the inlet is h-60 mm. Assume that the flow angle at the inlet of the impeller is 90 degree, calculate absolute velocity C1. • a. C1=3.93 m/s b. Cr1=10.3 m/s c. Cr1=5.93 m/s d. None of them are correct e. It is not possible to calculate C1- Because the tangential velocity of the impeller is not given.arrow_forward
- Q1// the velocity of steam at inlet to simple impulse turbine is 1000 m/s and the nozzle single is 20°. The blade speed is 400 m/s and the blades are symmetrical. Determine the blade angle, tangential force, diagrame power, axial thrust, and the diagram efficiency for frictionless blades. If the relative velocity at exit is reduced by friction to 80% of that at inlet, then recalculates the diagram power, axial thrust, and the diagram efficiency. Take mass flow rate 1 kg/s .Answer (32.5°, 1065.27 N, 426.27 kW, 0 N, 85.25 %,* 383.643 kW, 67.89 N, 76.7%)arrow_forward- A centrifugal pump with an impeller diameter of 350mm and specific speed of 19.15 and requires 15 kW to discharge 2.4 m³ /min of water, and runs at 1800 rpm. Determine the discharge, head and power required when the pump runs at 2400 rpm. The same discharge could be obtained by altering the impeller diameter without changing the rotational speed for this case find the new diameter of the impeller the head and the power required.arrow_forwardThe fluid flow rate was 1 m3 / s and the head was 10 m in the experiment performed at 2000 rev/min by water with the 1/4 ratio model of a centrifugal pump designed to be used for oil. Calculate the power given by the pump to the fluid when the prototype pump operates at 1000 rev/min (ρ water = 1000 kg / m3, ρ oil = 800 kg / m3)arrow_forward
- A centrifugal pump of 1.5 m diameter runs at 210 rpm and pumps 1800 lit/sec. The angle which the vane makes, at exit, with the tangent to the impeller is 25°. Assuming radial entry and velocity of flow throughout as 2.5 m/sec, determine the power required to drive the pump. If manometric efficiency of the pump is 65%, whirl velocity at inlet:arrow_forwardThe velocity of steam at inlet to a simple impulse turbine is 1000 m's, and the nozzle angle is 20°. The blade speed is 400 m/s and the blades are symmetrical. Determine the blade angles if the steam is to enter the blades without shock. If the friction effect s on the blade is negligible, calculate the tangential force on the blades and the diagram power for a mass flow of 0.75 kg/s. What is the axial thrust and the diagram efficiency? If the relative velocity at exit is reduced by friction to 80% of that at inlet, what is then the diagram power and the axial thrust? Calculate also the diagram efficiency in this case.arrow_forwardCalculate the power available in the wind and the rotor power when the blade length for the turbine is given 54 m and the wind speed is 6 m/s. The power coefficient of blades is 0.4, generator efficiency is 81 % while gear box efficiency is 0.9, air density is 1.225 kg/m3. Power available in the wind Power available in the rotorarrow_forward
- The system displays a hydraulic configuration. The pump draws oil whose relative density is 0.90 to a container and transmits it to the hydraulic cylinder with an internal diameter of 5" and in 15 s the piston moves 20" while exerting a force of 11,000 lb. It is estimated that there are energy losses of 11.5 lb-ft/lb and 35lb-ft/lb in the suction line and in the discharge line, respectively. Both lines are 3/8” 40 gauge steel. Determine: a) the rate of flow past the pump b) the pressure in the cylinder c) the pressure at the pump outlet d) the pressure at the pump input e) the power transmitted to the oil by the pump.arrow_forwardA 25Hp suction pump operating at 56.30% efficiency draws water from a suction line whose diameter is 205mm and discharges into air through a line whose diameter is 155mm . The velocity in the 155mm line is 4m/s . If the pressure at point A in the suction pipe is -32kpa (negative sign indicate the pressure is below the atmosphere), where A is 1.8m below B on the 155mm line, determine the maximum elevation above B to which water can be raised assuming a head loss of 2.9m due to friction.arrow_forwardCalculate the inlet blade velocity (m/s) of the Francis turbine that receives water under net head of 31 m and the speed ratio is 0.85. Assume the gravitational acceleration of 9.81m/s². Answer to 2 decimalsarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License