Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 39, Problem 1TF
To determine
The truth of the statement.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
Technician A says that some manual transmissions use 85/90 weight gear oil or synchromesh transmission fluid.Technician B says that some manual transmissions use automatic transmission fluid.Who is correct?
While discussing valve body assemblies in late-model transmissions: Technician A says that the valve body is no longer needed in some electronically controlled transmissions. Technician B says that an EPC solenoid maintains constant fluid pressure through the valve body regardless of the vehicle’s operating condition. Who is correct?
Some CVT transaxles do not have torque converter. What is used is its place?
Chapter 39 Solutions
Automotive Technology
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2SACh. 39 - Prob. 3SACh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - What should you do to properly identify the type...Ch. 39 - List at least five items that are typically...Ch. 39 - Prob. 1TFCh. 39 - True or False? Bearing noise increases under load...
Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - Technician A says that shims may be used to adjust...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A says that all manual transmission vehicles have at least one pilot bearing or bushing for the input shaft. Technician B says that the pressure plate always rotates with the input shaft when the engine is running. ‘Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhen servicing transfer cases, all of the following are correct, except_____. a. it must be supported on a transmission jack or safety stands b. the chain drive and a planetary gearset must be adjusted to specifications c. visual inspections for leaks and damage are necessary d. follow the manufacturers recommendations for lubricantsarrow_forwardTrue or False? The vent in a transmission housing is designed to allow fluid to escape when there is excessive pressure in the system.arrow_forward
- While checking the engine and transmission mounts on a FWD car: Technician A says that any engine movement may change the effective length of the shift and throttle cables and therefore may affect the engagement of the gears. Technician B says that delayed or missed shifts are caused by hydraulic prob lems, not linkage or control problems. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardTechnician A says that the proper fluid level for a manual transmission is normally to the bottom of the filler hole. Technician B says that low lubricant levels can cause a standard transmission to clash during shifting. Who is correct?arrow_forwardmanual transmissions are being discussed. technician a says that if it requires gear oil, to always use gl-5 rated oil to protect the synchronizers. technician b says that if it requires engine oil that you should add a friction modifier to it. who is correct?arrow_forward
- 128) Technician A says slide hammer pullers are usually required to remove the front pump from the transmission housing. Technician B says a special tool is available to remove the front pump on some transmissions. Which technician is correct? O Technician A Technician B O Both technicians A and B Neither technician A nor Barrow_forwardTechnician A says that an in-line six-cylinder diesel engine is usually longer and heavier than a V8 engine of the same displacement. Technician B says that there are twice as many teeth on the crankshaft as there are on the camshaft sprocket. Who is correct? and why? Technician A Technician B Both A and B Neither A nor Barrow_forward120) Technician A says that RWD transmission valve bodies are serviceable from under the vehicle. Technician B says that most FWD transmission valve bodies are serviceable from under the hood. Which technician is correct? Technician A O Technician B Both technicians A and B O Neither technician A nor Barrow_forward
- True or False? Make sure you locate and adhere to the wet torque specs when tightening a bolt that has been lubricated with oil or any other liquid.arrow_forwardTechnician A says that changes in engine load cause changes in hydraulic pressure inside the transmission. Technician B says that engine load is monitored by throttle pedal movement or by engine vacuum. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardWhich type of transmission uses pulleys to change engine speed? Dual-dutch Manual Continuously varaible Automaticarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning