Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 39, Problem 1MC
A rough, growling noise that is heard from a transaxle while it is in neutral with the engine running, the vehicle stationary, and the clutch engaged is a likely indication that there is a problem in the
a. transaxie input shaft bearings
b. transaxie main (intermediate) shaft bearings
c. first/second synchronizer assembly
d. pinion and ring gear interaction
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
When the clutch is disengaged, the power flow stops at the.a. transmission input shaftb. driven disc hubC. pressure plate and flywheeld. torsion springs
The component used to ensure that the mainshaft (output shaft) and main (speed) gear locked to it are rotating at the same speed is known as a_____.
a. synchronizer
b. shift detent
c. shift fork
d. transfer case
QUESTION 9
Which of the following is the best choice when selecting a belt drive to transmit power at a constant angular velocity ratio?
OA. Flat belt drive
OB. V-belt drive
OC. Oval belt drive
O D. Round belt drive
O E. Timing belt drive
QUESTION
4
Chapter 39 Solutions
Automotive Technology
Ch. 39 - After draining gear oil from a transaxie, the...Ch. 39 - Prob. 2SACh. 39 - Prob. 3SACh. 39 - What tool is often required to remove gears and...Ch. 39 - When removing or installing bearings, where should...Ch. 39 - List five common sources for transmission fluid...Ch. 39 - What should you do to properly identify the type...Ch. 39 - List at least five items that are typically...Ch. 39 - Prob. 1TFCh. 39 - True or False? Bearing noise increases under load...
Ch. 39 - A rough, growling noise that is heard from a...Ch. 39 - A clicking noise during transrnission/transaxle...Ch. 39 - Worn teeth on a speed gear can cause_______. a....Ch. 39 - Using a lubricant that is thicker than the...Ch. 39 - A poorly adjusted shift linkage can cause which of...Ch. 39 - Technician A says that the transmission rear seal...Ch. 39 - A noise occurs in forward and reverse gears but...Ch. 39 - A rough, growling noise occurs when a vehicle with...Ch. 39 - A car jumps out of gear into neutral, particularly...Ch. 39 - While diagnosing a noise from a transmission:...Ch. 39 - Technician A says that broken or worn engine and...Ch. 39 - Technician A says that shims may be used to adjust...Ch. 39 - During a test drive, a noise that appears to be...Ch. 39 - While inspecting the synchronizers of a transaxle:...Ch. 39 - Technician A says that the proper fluid level for...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Which of the following is probably not the cause of avibrating clutch?a. Excessive crankshaft end playb. Out-of-balance pressure plate assemblyc. Excessive flywheel runoutd. Loose flywheel boltsarrow_forward1. Torque converter it is part of brake axle clutch Automatic transmission 2. .is the source of the power in the vehicle. dund engine clutch Automatic transmission 3. The final gear reduction in the drive train occurs in the. . assembly. drive shaft rear wheel friction disc differentialarrow_forwardTechnician A says a multiple-disc holding clutch is used to lock the input and output shafts together. Technician B says a multiple-disc driving clutch is used to lock the planetary ring gear to the transmission case. Who is correct? Technician A Technician B Both technicians A and B Neither technician A noг Вarrow_forward
- While inspecting a planetary gear-type final drive, Technician A says blackened pinion shafts indicate severe overloading. Technician B says bluish gears indicate overheating. Who is correct?arrow_forwardExplain the role of shift rails and shift forks in the operation of a transmission or transaxle.arrow_forwardTechnician A says that if the shift for all forward gears is delayed, a slipping forward clutch is normally indicated. Technician B says that a bad forward clutch is indicated when there is a slip when the transmission shifts into any forward gear. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forward
- In a typical all wheel drive automatic transaxle, what controls the transfer clutch?a. Transmission control unit operating the pressure regualtor valveb. Engine computer controlling the line pressure to the various clutches in transmissionc. Transmission control unit and the duty solenoidd. Front axle speed sensor and vehicle speed sensor.arrow_forwardInsufficient clutch pedal clearance results in_ _ _ _ _ _ _ _ _ .a. gear clashing while shifting transmissionb. a noisy front transmission bearingc. premature release bearing failured. premature pilot bearing failurearrow_forwardA clicking noise during transmission/transaxle operationmay be an indication of __ .a. worn mainshaft (input shaft) bearingsb. faulty synchronizer operationc. failed oil sealsd. worn, broken, or chipped gear teetharrow_forward
- Units 5 & 6: Closed Gear Systems If two discs are fixed by an axis, their radial velocity and acceleration is equal. Essay Questions Multiple-Choice Question A. True B. False tandem are called what? What important element must we consider when re-scaling a gear system design? A. Space between the elements Cog C. Rack B. Recommended minimal element thickness C. Removal of support material is still possible D. None of the above D. Transmission g ng gearayoo ear teeth prevent eli C. Decreaseo D. Gear svstems are easy to design and manufacture Torce Ked ihe e uDove In Spur gear systems, the tooth profile is A. inclined to the axis of rotation. B. vertical to the axis of rotation. C. parallel to the axis of rotation. D. None of thesearrow_forwardbriefly define the following: 1. airborne transmission 2. common vehicle transmission 3. contact transmissionarrow_forwardWhen replacing an accessory drive belt, all the following are important considerations EXCEPT: Select one: a. Pulley alignment b. Crankshaft to camshaft timing c. Belt dimensions d. Belt routingarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License