Automotive Technology
7th Edition
ISBN: 9781337794213
Author: ERJAVEC, Jack.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 34, Problem 5MC
How much pressure does a typical EVAP pressure tester apply to the system during testing?
a. 14 in. Hg
b. 14 psi
c. 1 in. H2O
d. 0.5 psi
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
If H=16cm, what is the pressure gauge reading?
Air
H.
4m
Water
Hg
What are two limitations for the following
test methods? (80 - 100 Words)
a. Compression test - Dry
b. Compression test - Wet
c. Leak-down test
d. Oil pressure test
e. Vacuum test
The gage pressure reading on an automobile tire is 35 psi when the temperature is 0oF. The automobile is driven to a warmer climate and the temperature increases to 120oF. Estimate the increased pressure in the tire.
a.47.97 psig
b. 54.24 psig
c.58.91 psig
d.
Chapter 34 Solutions
Automotive Technology
Ch. 34 - A rich air-fuel ratio causes HC emissions to...Ch. 34 - What will result from too little EGR flow? And...Ch. 34 - What can result from a charcoal canister that is...Ch. 34 - What happens if a PCV valve is stuck in the open...Ch. 34 - Explain why the I/M 240 and similar tests are...Ch. 34 - How do you test the efficiency of a secondary AIR...Ch. 34 - List five common causes for high HC emissions.Ch. 34 - Describe carbon monoxide (CO) emissions in...Ch. 34 - An EGR valve that does not fully close can cause...Ch. 34 - A restricted catalytic converter can cause all of...
Ch. 34 - Which of the following statements about EVAP...Ch. 34 - As a catalytic converter begins to deteriorate,...Ch. 34 - How much pressure does a typical EVAP pressure...Ch. 34 - Which of the following exhaust gases is typically...Ch. 34 - Prob. 7MCCh. 34 - While discussing the proper way to test a...Ch. 34 - Prob. 2ASRQCh. 34 - While discussing catalytic converter diagnosis:...Ch. 34 - While discussing EGR valve diagnosis: Technician A...Ch. 34 - While discussing EGR valve diagnosis: Technician A...Ch. 34 - When discussing the diagnosis of a positive back...Ch. 34 - While diagnosing a PCV problem: Technician A says...Ch. 34 - Technician A says that the AIR system should pump...Ch. 34 - While discussing PCV system diagnosis: Technician...Ch. 34 - While discussing EVAP testing: Technician A says...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- While discussing a pressure test: Technician A says that a pressure drop of more than 15 psi during a shift indicates a possible leak. Technician B says that any pressure drop between shifts indicates a problem. Who is correct? a. Technician A only b. Technician B only c. Both A and B d. Neither A nor Barrow_forwardThe gage atmospheric pressure is 1 bar Select one: True O Falsearrow_forwardTypically during a pressure test, the pressure should not drop more than_____ psi between shifts.arrow_forward
- Question 30 Not yet answered Marked out of1.00 P Flag question 5.8 bar pressure is equivalent to mm of mercury. O a. 4347.30 O b.42647.06 OC 4547949.50 O d. 4.35arrow_forward2.A. You can usually check for a leak in a vacuum system by looking at or feelingA. at the exhaust of the vacuum pump.B. at the vacuum gauge at the vacuum pump.C. for signs of dirt on the piping. 2.B. When you measure the voltage drop across a set of contacts, you'reA. checking the quality of the contact set.B. sensing how much current is flowing in the circuit.C. measuring the equivalent motor resistance. 2.C. A chain-drive system can be aligned easier than a belt-drive system since the chain-drive systemA. can have a string left on the sprockets after the alignment is complete.B. can have the chain removed while the final alignment is taking place.C. is less critical to misalignment.arrow_forwardTechnician A says that if the oil pressure shows low on the vehicle's gauge, engine oil pressure should be verified using a manual test gauge. Technician B says that if a vehicle's oil pressure gauge reads too high, engine oil pressure should be verified using a manual test gauge. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor Barrow_forward
- TRUE OR FALSE: The pressure variation from any point to another will be determined by applying Newton’s second law.arrow_forwardCoolant condition can be tested with all the following tools EXCEPT: Select one: a. Hydrometer b. Barometer c. Refractometer d. Electronic testerarrow_forwardThe following transducer is used to measure the temperature. a. Bourdon tube b. Bellows c. Thermocouple d. Strain Gaugearrow_forward
- True or False: To check the temperature leads of an electronic thermometer for low temperatures, they should be stirred in a container of crushed ice, water, and a table-spoon of salt.arrow_forwardName the three types of stress testing used to test for intermittent ignition component problems and list the procedures for conducting each type of test.arrow_forwardWhat is thermocouple gauge used for detection of leaks in vacuum systems.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningAutomotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
What is Metrology in Mechanical Engineering? | Terminologies & Measurement; Author: GaugeHow;https://www.youtube.com/watch?v=_KhMhFRehy8;License: Standard YouTube License, CC-BY