Automotive Technology: A Systems Approach (MindTap Course List)
Automotive Technology: A Systems Approach (MindTap Course List)
6th Edition
ISBN: 9781133612315
Author: Jack Erjavec, Rob Thompson
Publisher: Cengage Learning
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 27, Problem 1RQ

Name the three types of stress testing used to test for intermittent ignition component problems and list the procedures for conducting each type of test.

Expert Solution & Answer
Check Mark
To determine

The types of stress testing used for testing intermittent ignition problems.

Answer to Problem 1RQ

There are three types of stress testing used for conducting testing the intermittent ignition component problems. They are cold testing, heat testing, and moisture testing.

Explanation of Solution

The stress testing is of three types:

  1. Cold testing
  2. Heat testing
  3. Moisture testing

Now, the following are the methods of stress testing:

Procedure to be followed in case of cold testing:

  1. In this kind of testing, first, the ignition components are cooled by using a liquid which is later used as a cooling agent.
  2. Then, the traces of any malfunction or problem in the pattern within the dwell zone is observed and checked.
  3. Then, this same procedure is being followed and repeated again for the other components in this test. By doing this, results are compared and bad ones are observed and pointed out.

Procedure to be followed in case of heat testing:

  1. In this testing, the ignition components are heated by using the heat gun which puts hot air in the components. Doing this process, the degree should be kept in that much value so that plastic and wire does not get damaged.
  2. Then, the traces of any malfunction or problems in the pattern within the dwell zone and the area of limited flow is observed and checked.
  3. In case of malfunction found, the terminals should be cleaned and coated.

Procedure to be followed in case of moisture testing:

  1. In this testing, the ignition components are being sprayed a little with water and the raster which is connected to the scope provides the pattern of the problem which is found in it.
  2. Although, in some cases, instead of using the scope, the problems can be identified by hearing the shutter.

Conclusion:

Thus, there are three kinds of stress testing.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Complete the following statement about compression testing using the following words. Words: Accurate, All, Battery, Button, Comparison, Compression, Consistent, Cylinders, Four, Fuel,Gauges, Hole, Increase, Install, Observe, Reading, Recorded, Remote, Revolution, Screw-in, Spark,Starter, Test, Warm, Wide-open 1 Before conducting a __________ test, disable the ignition and the __________ injection system.Most manufacturers recommend that the engine be __________ when testing.2 Prop the throttle plate into a __________ position to allow an unrestricted amount of air to enterthe __________ during the test.3 Remove __________ of the engine’s __________ plugs.4 Connect a __________ starter button to the __________ system.5 Many types of compression __________ are available. The __________ type tends to be the most__________ and easiest to use.6 Carefully __________ the gauge into the spark plug __________ of the first cylinder.7 Connect a __________ charger to the car to allow the engine…
i need the answer quickly
What are the equipment/apparatus required to conduct performance test of internal combustion engine?
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Text book image
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Text book image
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Text book image
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Text book image
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Text book image
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY