7th Edition

ISBN: 9780133128741

Author: Serope Kalpakjian, Steven Schmid

Publisher: Prentice Hall

Concept explainers

It is the process of permanent or temporary joining of two metal pieces with the help of heat or pressure. Two metal parts are assembled by applying an energy source for the formation of a single unit. The obtained joined metals cannot be fragmented easi…

Videos

Textbook Question

Chapter 32, Problem 2RQ

Are fluxes necessary in brazing? If so, why?

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 32, Problem 1RQ

Chapter 32, Problem 3RQ

Students have asked these similar questions

What is the difference between soldering, brazing and welding?

Which of the following ways of filler metals is applied to the brazing operation; * Rod Powders Strips O All of the mentioned

a). Write the types of brazing Process and explain any one type of brazing process in detail.b). Write the applications of brazing process.

Chapter 32 Solutions

Manufacturing Engineering & Technology

Ch. 32 - What is the difference between brazing and...Ch. 32 - Are fluxes necessary in brazing? If so, why?Ch. 32 - Why is surface preparation important in...Ch. 32 - What materials are typically used in solder?Ch. 32 - Soldering is generally applied to thinner...Ch. 32 - Explain the reasons why a variety of mechanical...Ch. 32 - List three brazing and three soldering techniques.Ch. 32 - Describe the similarities and differences between...Ch. 32 - What precautions should be taken in the...Ch. 32 - What difficulties are involved in joining...

Ch. 32 - Prob. 11RQ Ch. 32 - What are the principles of (a) wave soldering...Ch. 32 - What is a peel test? Why is it useful?Ch. 32 - What is a combination joint?Ch. 32 - Prob. 15RQ Ch. 32 - Prob. 16QLP Ch. 32 - Prob. 17QLP Ch. 32 - Comment on your observations concerning the...Ch. 32 - Give examples of combination joints other than...Ch. 32 - Discuss the need for fixtures for holding...Ch. 32 - Explain why adhesively bonded joints tend to be...Ch. 32 - It is common practice to tin-plate electrical...Ch. 32 - Give three applications where adhesive-bonding is...Ch. 32 - Prob. 24QLP Ch. 32 - If you are designing a joint that must be strong...Ch. 32 - Prob. 26QLP Ch. 32 - Rate lap, butt, and scarf joints in terms of...Ch. 32 - Prob. 28QLP Ch. 32 - Prob. 29QTP Ch. 32 - Prob. 30QTP Ch. 32 - Prob. 31QTP Ch. 32 - Figure 32.4 shows qualitatively the tensile and...Ch. 32 - When manufacturing the fuselage of a commuter...Ch. 32 - Prob. 34SDP Ch. 32 - Name several products that have been assembled...Ch. 32 - Suggest methods of attaching a round bar (made of...Ch. 32 - Prob. 38SDP Ch. 32 - Prob. 39SDP Ch. 32 - Prob. 40SDP Ch. 32 - Prob. 41SDP Ch. 32 - Describe part shapes that cannot be joined by...Ch. 32 - Prob. 43SDP Ch. 32 - Prob. 44SDP Ch. 32 - Prob. 45SDP Ch. 32 - Prob. 46SDP Ch. 32 - Review Fig. 32.9a and explain the shortcoming...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Are fluxes necessary in brazing? If so, why?

Solution Summary: The author explains that brazing and soldering fluxing agents or a précised atmosphere should be used. The tenacity of the flux is to eliminate oxides on base material and to avoid oxidation in heating process

Concept explainers

Videos

Want to see the full answer?

Chapter 32 Solutions