Manufacturing Engineering & Technology
7th Edition
ISBN: 9780133128741
Author: Serope Kalpakjian, Steven Schmid
Publisher: Prentice Hall
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 32, Problem 22QLP
It is common practice to tin-plate electrical terminals to facilitate soldering. Why is it used?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Give information about the reasons why the weld is preferred over other fastening methods.
What is soldering? What is solder?
What is a cold solder joint? Identify its causes, its appearance, and the means of correction.
Chapter 32 Solutions
Manufacturing Engineering & Technology
Ch. 32 - What is the difference between brazing and...Ch. 32 - Are fluxes necessary in brazing? If so, why?Ch. 32 - Why is surface preparation important in...Ch. 32 - What materials are typically used in solder?Ch. 32 - Soldering is generally applied to thinner...Ch. 32 - Explain the reasons why a variety of mechanical...Ch. 32 - List three brazing and three soldering techniques.Ch. 32 - Describe the similarities and differences between...Ch. 32 - What precautions should be taken in the...Ch. 32 - What difficulties are involved in joining...
Ch. 32 - Prob. 11RQCh. 32 - What are the principles of (a) wave soldering...Ch. 32 - What is a peel test? Why is it useful?Ch. 32 - What is a combination joint?Ch. 32 - Prob. 15RQCh. 32 - Prob. 16QLPCh. 32 - Prob. 17QLPCh. 32 - Comment on your observations concerning the...Ch. 32 - Give examples of combination joints other than...Ch. 32 - Discuss the need for fixtures for holding...Ch. 32 - Explain why adhesively bonded joints tend to be...Ch. 32 - It is common practice to tin-plate electrical...Ch. 32 - Give three applications where adhesive-bonding is...Ch. 32 - Prob. 24QLPCh. 32 - If you are designing a joint that must be strong...Ch. 32 - Prob. 26QLPCh. 32 - Rate lap, butt, and scarf joints in terms of...Ch. 32 - Prob. 28QLPCh. 32 - Prob. 29QTPCh. 32 - Prob. 30QTPCh. 32 - Prob. 31QTPCh. 32 - Figure 32.4 shows qualitatively the tensile and...Ch. 32 - When manufacturing the fuselage of a commuter...Ch. 32 - Prob. 34SDPCh. 32 - Name several products that have been assembled...Ch. 32 - Suggest methods of attaching a round bar (made of...Ch. 32 - Prob. 38SDPCh. 32 - Prob. 39SDPCh. 32 - Prob. 40SDPCh. 32 - Prob. 41SDPCh. 32 - Describe part shapes that cannot be joined by...Ch. 32 - Prob. 43SDPCh. 32 - Prob. 44SDPCh. 32 - Prob. 45SDPCh. 32 - Prob. 46SDPCh. 32 - Review Fig. 32.9a and explain the shortcoming...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Why is cost a consideration in joint design?arrow_forwardThe current required for 5mm thick steel plates to be spot welded is 10,000amps. Then the current required for 1.5mm thick aluminium plates to spot weld, will be A. (Melting point of steel = 1400°C and melting point of Al = 660°C)arrow_forward(a) With the aid a diagram, describe the principle of spot-welding process.arrow_forward
- Riveting is an example of electrical and electronical joining process. Select one: True Falsearrow_forwardA welding operation is time-studied during which an operator was pace-rated as 120%. The operator took, on an average, 8 minutes for producing the weld-joint. If a total of 10% allowances are allowed for this operation. What is the expected standard production rate of the weld-joint in units per 8 hour day?arrow_forward2) Which of the following is NOT true about friction stir welding? O It is a solid state process Fine grained structures can be obtained O It eliminates friction welding problems O It alters the chemical composition of the workpiecearrow_forward
- How do tools affect the accuracy of the finished workpiece in welding works? Is it possible to have an accurate workpiece without welding tools or instruments?arrow_forward* نقطة واحدة Stick" welding is a term sometimes" applied when referring to which one of :the following processes FCAWO GMAWO GTAW SMAW Oarrow_forwardIn Resistant Spot Welding (RSW), select TWO (2) appropriate type of electrode material when joining non-ferrous metals.arrow_forward
- Identify the conditions under which a brazed joint is likely to be “stronger” than the brazing material by itself. Describe the trends in joint fracture strength as it becomes wider/narrower or thinner/thicker.arrow_forward8) The purpose of using flux in soldering is to.... O Increase fluidity of solder metal O Feel up gaps left in a bad joint Prevent oxides forming O Wash away surplus solderarrow_forwardWhat effect does the end shape of the tungsten have on its own welding performance? Note: answer the question briefly but informative.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Metal Joining Process-Welding, Brazing and Soldering; Author: Toc H Kochi;https://www.youtube.com/watch?v=PPT5_fDSzGY;License: Standard YouTube License, CC-BY